Items where Division is "Mechanical Engineering" and Year is 2014

Article

Saud, Safaa N. and Hamzah, Esah and Abubakar, T. and Refaei, Azadeh and Hosseinian, Raheleh (2014) The influence of γ-irradiation on the structure and properties of the Cu-11.5 wt. % Al-4 wt. % Ni shape memory alloys. Advanced Materials Research, 845 . pp. 128-132. ISSN 1022-6680

Lim, Hooi Peng and Ourdjini, Ali and Abu Bakar, Tuty Asma (2014) The effects of nickel underlayer and solder dipping as tin whisker mitigations in tin surface finishes. Applied Mechanics and Materials, 554 . pp. 47-51. ISSN 1660-9336

Kherbeet, A. S. and Mohammed, Hussein A. and Munisamy, K. M. and Salman, B. H. (2014) The effect of step height of microscale backward-facing step on mixed convection nanofluid flow and heat transfer characteristics. International Journal of Heat and Mass Transfer, 68 . pp. 554-566. ISSN 0017-9310

A. Rasid, Zainudin and Zahari, R. and Ayob, Amran (2014) The instability improvement of the shape memory alloy composite plates subjected to in-plane parabolic temperature distribution. Applied Mechanics and Materials, 554 . pp. 32-36. ISSN 1660-9336

A. Rasid, Zainudin and Zahari, Rizal and Ayob, Amran (2014) The instability improvement of the symmetric angle-ply and cross-ply composite plates with shape memory alloy using finite element method. Advances in Mechanical Engineering, 2014 . pp. 1-11. ISSN 1687-8132

Abas, Fatimatul Zaharah and Nasir Ani, Farid (2014) Comparing characteristics of oil palm biochar using conventional and microwave heating. Jurnal Teknologi (Sciences and Engineering), 68 (3). pp. 33-37. ISSN 2180-3722

Abas, Mohd. Azman and Wan Salim, Wan Saiful Islam and Botas Ricardo, Martinez and Rajoo, Srithar (2014) Efforts to establish Malaysian urban drive-cycle for fuel economy analysis. SAE Technical Papers, 1 .

Abd. Kader, Ab. Saman and Ahmad, Mohd. Zamani and Ahmad Fuad, Ahmad Faizal and Asmawi, A.M. (2014) Compatibility as an additional criterion for life saving performance of life jacket. Journal of Applied Science and Agriculture, 9 (18). pp. 202-208. ISSN 1816-9112

Abd. Rahim, Shayfull Zamree and Sharif, Safian and Mohd. Zain, Azlan and Mohd. Saad, Rozaimi and Fairuz, M. A. (2014) Warpage analysis with straight drilled and conformal cooling channels on front panel housing by using Taguchi method. Advanced Materials Engineering and Technology Ii, 594-59 . pp. 593-603. ISSN 1013-9826

Abdi, B. and Abu Hassan, Shukur and Wahit, Mat Uzir and Abdul Hanan, Umar (2014) Tensile and flexural properties of recycled glass fibre reinforced polyester composite. Materials Research Innovations, 18 . S6187-S6189. ISSN 1432-8917

Abdi, Behzad and Azwan, Syed and Ayob, Amran and Abdul Rahman, Roslan and Abdullah, R. A. (2014) Experimental investigation on free vibration of foam-core sandwich plate with and without circular polymer columns. Advanced Materials Research, 845 . pp. 297-301. ISSN 1022-6680

Abdolahi, Ahmad and Hamzah, Esah and Hashim, Shahrir and Ibrahim, Zaharah (2014) Synthesis and characterization of polyaniline- polypyrrole composite. Advanced Materials Research, 845 . pp. 795-798. ISSN 1022-6680

Abdolahi, Ahmad and Hamzah, Esah and Ibrahim, Zaharah and Hashim, Shahrir (2014) Application of environmentally-friendly coatings toward inhibiting the microbially influenced corrosion (MIC) of steel: a review. Polymer Reviews, 54 (4). pp. 702-745. ISSN 1558-3724

Abdolbaqi, M. Kh and Che Sidik, Nor Azwadi and Mamat, Rizalman (2014) Heat transfer augmentation in the straight channel by using nanofluids. Case Studies in Thermal Engineering, 3 . pp. 59-67. ISSN 2214-157X

Abdul Awal, Ziad and Ammoo, Mohd. Shariff (2014) A case study on the air flow characteristics of the Hirobo-FALCON 505 controllable helicopter's main rotor blade. Applied Mechanics and Materials, 527 . pp. 39-42. ISSN 1660-9336

Abdul Halim, Zulhelmi Alif and Mat Yajid, Muhamad Azizi and Mohd. Rosli, Zulkifli and Mohamad Ali, Riyaz Ahmad (2014) Aluminum-copper bilayers thin films deposited at room temperature by RF magnetron sputtering. Applied Mechanics and Materials, 606 . pp. 105-109. ISSN 1660-9336

Abdul Hamid, Mohd. Kameil and Kaulan, A. M. and Abu Bakar, Abd. Rahim and Wan Nik, W. B. (2014) Burnishing effect on disc brake corrosion and frictional performance of corroded disk. Jurnal Teknologi (Sciences and Engineering), 66 (3). pp. 59-64. ISSN 0127-9696

Abdul Hamid, Mohd. Kameil and Shasudin, N. I. and Mat Lazim, Ahmad Razimi and Abu Bakar, Abd. Rahim (2014) Effect of brake pad design on friction and wear with hard particle present. Jurnal Teknologi, 71 (2). pp. 135-138. ISSN 0127-9696

Abdul Latiff, Zulkarnain and Cheong, Weng Soon and Supriyo, Bambang and Mohd. Perang, Mohd. Rozi and Nasution, Henry and Abdul Aziz, Azhar (2014) Experimental study on the performance of in-cabin ventilation system. Advances in Applied Mechanics and Materials, 493 . pp. 251-255. ISSN 1660-9336

Abdul Malik, Adi Maimun and Ahmed Abdel Razak, Yasser Mohamed and Jaswar, Jaswar and Priyanto, Agoes and Nakisa, Mehdi and Behrouzi, Fatemeh and Ghazanfari, Seyed Alireza and Ang, Yit Sian (2014) Ship navigation effect on sedimentation in restricted waterways. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 143-147. ISSN 0127-9696

Abdul Rahim, Rabiatul Adibah and Mohd. Szali Januddi, Mohd. Al-Fatihhi and Syahrom, Ardiyansyah and Harun, Muhamad Noor and Abdullah, Jaafar and Afriwardi, Afriwardi (2014) Study the effect of fluid medium toward synthetic cancellous bone structure. Advanced Materials Research, 845 . pp. 335-339. ISSN 1022-6680

Abdul Wahid, Mazlan and Hosseini, Seyed Ehsan (2014) Enhancement of exergy efficiency in combustion systems using flameless mode. Energy Conversion and Management, 86 . pp. 1154-1163. ISSN 0196-8904

Abdul Wahid, Mazlan and Mailah, Musa and Mazalan, Nor Azizi and Malek, A. A. (2014) Review of control strategies employing neural network for main steam temperature control in thermal power plant. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 73-76. ISSN 0127-9696

Abdullah, M. Adlan and Ani, Farid Nasir and Hassan, Masjuki (2014) The effects of injection parameters on the performance of common rail light duty engine fueled with palm oil biodiesel. Applied Mechanics and Materials, 465-46 . pp. 322-326. ISSN 1660-9336

Abdullah, Mohamed Ruslan and Goharian, Amirhossein and Abdul Kadir, Mohammed Rafiq and Wahit, Mat Uzir (2014) Processing of a multi-layer polyetheretherketone composite for use in acetabular cup prosthesis. Journal of Applied Polymer Science, 131 (20). ISSN 0021-8995

Abdullah, Shariman and Mailah, Musa and Tang, Collin Howe Hing (2014) AFC motor control using low cost and mobile data acquisition system with dsPIC30 microcontroller and Lubin Kerhuel blockset for MATLAB/Simulink. 4th Mechanical and Manufacturing Engineering, PTS 1 and 2, 465-46 . pp. 806-810. ISSN 1660-9336

Abrishamkar, M. and Hussein, Mohamed and Zakaria, K. and Maleki, H. (2014) TCP/IP-based control and monitoring of manufacturing system. Advanced Materials Research, 845 . pp. 975-979. ISSN 1022-6680

Abu Bakar, Abdul Rahim and Mailah, Musa and Dehkordi, S. M. Hashemi (2014) Stability analysis of a linear friction-induced vibration model and its prevention using active force control. Advances in Mechanical Engineering . ISSN 1687-8132

Abu Bakar, Saiful Anuar and Mohd. Samin, Pakharuddin and Jamaluddin, Hishamuddin and Abdul Rahman, Roslan (2014) Ride comfort performance improvement of electric vehicle (EV) conversion using SAS-controlled active suspension system. Jurnal Teknologi, 71 (2). pp. 113-120. ISSN 0127-9696

Abubakar, Muazu and Aliyu, A. B. and Ahmad, Norhayati (2014) Characterization of Nigerian clay as porous ceramic material. Advanced Materials Research, 845 . pp. 256-260. ISSN 1022-6680

Abuelnuor, Abdeen Ali and Abdul Wahid, Mazlan and Saat, Aminuddin and Osman, Mai A. R. (2014) Characterization of a low NOx flameless combustion burner using natural gas. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 121-125. ISSN 0127-9696

Abyn, Hassan and Abdul Malik, Adi Maimun and Islam, M. Rafiqul and Magee, Allan and Jaswar, Jaswar and Bodaghi, Behnam and Pauzi, Mohamad and Sio, C. L. (2014) Effect of mesh number on accuracy of semi submersible motion prediction. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 67-72. ISSN 0127-9696

Abyn, Hassan and Abdul Malik, Adi Maimun and Jaswar, Koto and Islam, Moni Rafiqul and Siow, C. L. and Bodaghi, Behnam (2014) TLP motion effect on semisubmersible motion. Proceedings of the Annual Offshore Technology Conference, 1 . pp. 538-548. ISSN 0160-3663

Abyn, Hassan and Abdul Malik, Adi Maimun and Koto, Jaswar and Rafiqul Islam, Mohammad and Magee, Allan and Bodaghi, Behnam and Pauzi, Mohamad and Siow, C. L. and Tofa, M. Mobassher (2014) Hydrodynamic interaction of floating structure in regular waves. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 91-96. ISSN 0127-9696

Adeyemi, Ademola James and Mohd. Rohani, Jafri and Abdul Rani, Mat Rebi (2014) Back pain arising from schoolbag usage among primary schoolchildren. International Journal of Industrial Ergonomics, 44 (4). pp. 590-600. ISSN 0169-8141

Adeyemi, Ademola James and Mohd. Rohani, Jafri and Olusegun, Akanbi Gabriel and Abdul Rani, Mat Rebi (2014) Anthropometric data reduction using confirmatory factor analysis. Work-A Journal of Prevention Assessment & Rehabilitation, 47 (2). pp. 173-181. ISSN 1051-9815

Afrizal, Efi and Koto, Jaswar (2014) Ice resistance performance analysis of double acting tanker in astern condition. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 73-78. ISSN 0127-9696

Afshar, Jafar and Sadeghiamirshahidi, Narjes and Firouzi, Ali Reza and Zahraee, Seyed Mojib and Syed Hassan, Syed Ahmad Helmi (2014) Improving the inventory levels of a blood supply chain through system dynamic simulation. Jurnal Teknologi (Sciences and Engineering), 69 (6). pp. 1-4. ISSN 0127-9696

Ahdash, Abdelsalam and Hamzah, Esah and Ourdjini, Ali and Abdolahi, Ahmad (2014) Characterizations of zeolite, polyaniline and zeolite/polyaniline as antifouling materials for marine applications. Advanced Materials Research, 845 . pp. 91-95. ISSN 1022-6680

Ahmad, Mohd. Azuwan and Adnan, Faizul Amri (2014) Evaluation of service performances of Liquefied Natural Gas Carriers in actual seas. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 33-43. ISSN 0127-9696

Ahmad, Mohd. Zamani and Abd. Kader, Ab. Saman (2014) The study to propose life jacket provision index static model for the assessment of the provision of life jacket on board coastal passenger vessel. Journal of Applied Science and Agriculture, 9 (18). pp. 185-189. ISSN 1816-9112

Ahmad, Zaini and Othman, M. S. (2014) Energy absorption performance of a rain forest vehicle under frontal impact. Journal of Mechanical Engineering and Sciences, 6 . pp. 807-817. ISSN 2289-4659

Ahmed, Sameh Elsayed and Hussein, Ahmed Kadhim and Mohammed, Hussein A. and Sivasankaran, S. (2014) Boundary layer flow and heat transfer due to permeable stretching tube in the presence of heat source/sink utilizing nanofluids. Applied Mathematics and Computation, 238 . pp. 149-162. ISSN 0096-3003

Ahmed, Sameh Elsayed and Hussein, Ahmed Kadhim and Mohammed, Hussein A. and Adegun, I. K. and Zhang, Xiaohui and Kolsi, Lioua and Hasanpour, A. and Sivasankaran, S. (2014) Viscous dissipation and radiation effects on MHD natural convection in a square enclosure filled with a porous medium. Nuclear Engineering and Design, 266 . pp. 34-42. ISSN 0029-5493

Ahmed, Yasser Mohamed and Yaakob, Omar and Sun, Bong K. (2014) Design of a new low cost ROV vehicle. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 27-32. ISSN 0127-9696

Ahmed Abdel Razak, Yasser Mohamed and Abdul Malik, Adi Maimun (2014) The perspective of hydropower as renewable energy. Journal Of Ocean, Mechanical And Aerospace -Science And Engineering, 11 . pp. 1-4. ISSN 2354-7065

Ahmed Abdel Razak, Yasser Mohamed and Yaakob, Omar and Elbatran, A. H. and Mazukee, U. J. A. (2014) Wells turbine for wave energy conversion for Malaysian ocean. Journal of Ocean, Mechanical and Aerospace-Science and Engineering-, 8 . pp. 12-16. ISSN 2354-7065

Akeiber, Hussein J. and Wahid, Mazlan A. and Hussen, Hasanen M. and Mohammad, Abdulrahman Th. (2014) Review of development survey of phase change material models in building. Scientific World Journal . ISSN 1537-744X

Alexandrov, Sergei and Yusof, Mustafa and Hwang, Yeong Maw and Lyamina, Elena (2014) An accurate upper bound solution for plane strain extrusion through a wedge-shaped die. Scientific World Journal, 2014 . ISSN 2356-6140

Alexandrov, Sergei E. and Yusof, Mustafa (2014) The strain rate intensity factor in the plane strain compression of thin anisotropic metal strip. MECCANICA, 49 (12). p. 2906. ISSN 0025-6455

Ali, Arifah and Abdul Malik, Adi Maimun and Ahmed, Yasser Mohamed (2014) CFD application in resistance analysis for advanced semi-SWATH vehicle. 4th Mechanical and Manufacturing Engineering, PTS 1 and 2, 465-46 . pp. 44-49. ISSN 1660-9336

Ali, Arifah and Maimun, Adi and Mohamed Ahmed, Yasser (2014) Numerical simulation on wave interference of catamaran with fin stabilizer. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 163-167. ISSN 0127-9696

Ali, Mohammad Abdo Hashem and Mailah, Musa and Tang, Collin Howe Hing and A. Rahim, Mohamed Akmal Baharain (2014) Algorithm to detect roundabout environments for mobile robot based on laser range finder and camera. 4th Mechanical and Manufacturing Engineering, PTS 1 and 2, 465-46 . pp. 796-800. ISSN 1660-9336

Ali, Mohammad Abdo Hashem and Mailah, Musa and Tang, Howe Hing and A. Rahim, Mohd. Akmal (2014) Autonomous mobile robot platform for on-the-road navigation. Advanced Materials Research, 845 . pp. 750-754. ISSN 1022-6680

Ammoo, Mohd. Shariff and Abdul Awal, Ziad (2014) Static and dynamic balancing of helicopter tail rotor blade using two-plane balancing method. Jurnal Teknologi, 71 (2). pp. 49-55. ISSN 0127-9696

Ammoo, Mohd. Shariff and Abdul Awal, Ziad and Khairudin, Khairul Shamil (2014) Structural analysis of UTM single-seat helicopter chassis. Jurnal Teknologi, 71 (2). pp. 57-64. ISSN 0127-9696

Andwari, Amin Mahmoudzadeh and Abdul Aziz, Azhar and Muhamad Said, Mohd. Farid and Abdul Latiff, Zulkarnain (2014) Experimental investigation of the influence of internal and external EGR on the combustion characteristics of a controlled auto-ignition two-stroke cycle engine. Applied Energy, 134 . pp. 1-10. ISSN 0306-2619

Ani, Farid Nasir and Mazharul, Islam and Muhammad, Ruhul Amin (2014) Evaluation of the prospects of using solar thermal air-conditioning systems in Saudi Arabia. Applied Mechanics and Materials, 554 . pp. 271-275. ISSN 1660-9336

Ani, Farid Nasir and Salema, Arshad Adam and Hassan, Ismail (2014) Bio-oils characteristic from oil palm biomass from different fast pyrolysis techniques. Applied Mechanics and Materials, 554 . pp. 266-270. ISSN 1660-9336

Anshar, Muhammad and Abd. Kader, Ab. Saman and Ani, Farid Nasir (2014) The utilization potential of rice husk as an alternative energy source for power plants in Indonesia. Advanced Materials Research, 845 . pp. 494-498. ISSN 1022-6680

Arafat, Andril and Idris, Mohd. Hasbullah and Abdul Kadir, Mohammed Rafiq and Jafari, Hassan (2014) Characterisation of calcium phosphate coating on investment cast 316L stainless steel. Materials Research Innovations, 18 . pp. 886-891. ISSN 1432-8917

Ardhyananta, Hosta and Baiti, Risa Nurin and Afrianto, Martha Adi and Kurniawan, Denni (2014) Analysis of fiber glass/vinyl ester composite subjected to internal pressure loading for compressed natural gas tube type IV application. Applied Mechanics and Materials, 493 . pp. 645-650. ISSN 1660-9336

Ashrul Bin Ishak, Mohamad Shaiful and Mohd. Jaafar, Mohammad Nazri and Chan, Ze Dar (2014) Study of droplet size for palm bio-fuel blends. American-Eurasian Journal of Sustainable Agriculture, 8 (7 SPEC). pp. 44-48. ISSN 1995-0748

Ashrul Ishak, Mohamad Shaiful and Mohd. Jaafar, Mohammad Nazri and Wan Omar, Wan Zaidi (2014) Experimental analysis on the formation of CO-NO-HC in swirling flow combustion chamber. Jurnal Teknologi, 72 (4). pp. 21-26. ISSN 2180-3722

Ayob, Amran and Yahya, Mohd. Yazid and Abdi, Behzad and Syed Hamzah, Syed Mohd. Saiful Azwan (2014) Quasi-static indentation behaviour of glass fibre reinforced polymer. Advanced Materials Research, 970 . pp. 317-319. ISSN 1022-6680

Ayob, Amran and Yahya, Mohd. Yazid and Syed Hamzah, Syed Mohd. Saiful Azwan and Abdi, Behzad (2014) Quasi-Static flexural and indentation behaviour of polymer-metal laminate. Advanced Materials Research, 970 . pp. 88-90. ISSN 1022-6680

Azwan, S. M. S. and Yahya, Mohd. Yazid and Abdi, Behzad and Ayob, Amran (2014) Loading rate effect on flexural and indentation behaviour of foam core composite sandwich panel. Jurnal Teknologi, 71 (2). pp. 159-162. ISSN 0127-9696

Bakhsheshi Rad, Hamid Reza and Hamzah, Esah and Daroonparvar, Mohammadreza and Kasiri-Asgarani, Masoud and Medraj, Mamoun (2014) Synthesis and biodegradation evaluation of nano-Si and nano-Si/TiO2 coatings on biodegradable Mg-Ca alloy in simulated body fluid. Ceramics International, 40 (9PartA). pp. 14009-14018. ISSN 0272-8842

Bakhsheshi-Rad, Hamid Reza and Hamzah, Esah and Daroonparvar, M. and Mat Yajid, M. Azizi and Medraj, Mamoun (2014) Fabrication and corrosion behavior of Si/HA nano-composite coatings on biodegradable Mg-Zn-Mn-Ca alloy. Surface & Coatings Technology, 258 . pp. 1090-1099. ISSN 0257-8972

Bakhsheshi-Rad, Hamid Reza Bakhsheshi and Hamzah, Esah and Daroonparvar, Mohammadreza R. and Saud, Safaa Najah and Abdul Kadir, Mohammed Rafiq (2014) Bi-layer nano-TiO2/FHA composite coatings on Mg-Zn-Ce alloy prepared by combined physical vapour deposition and electrochemical deposition methods. Vacuum, 110 . pp. 127-135. ISSN 0042-207X

Balaji, Rajoo and Yaakob, Omar (2014) Ballast water management triad: administration, ship owner and the seafarer. International Journal of Environmental, Ecological, Geological and Mining Engineering, 8 (8). pp. 474-477.

Balaji, Rajoo and Yaakob, Omar and Adnan, Faizul Amri and Koh, Kho King (2014) Design verification of heat exchanger for ballast water treatment. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 61-65. ISSN 0127-9696

Behrouzi, Farshad and Mohamed Shaharoun, Awaluddin and Ma'aram, Azanizawati (2014) Applications of the balanced scorecard for strategic management and performance measurement in the health sector. Australian Health Review, 38 (2). pp. 208-217. ISSN 0159-5709

Behrouzi, Fatemeh and Abdul Malik, Adi Maimun and Nakisa, Mehdi and Ahmed, Yasser Mohamed (2014) Arm effect on performance of vertical axis current turbine using RANS simulation. Applied Mechanics and Materials, 554 . pp. 531-535. ISSN 1660-9336

Behrouzi, Fatemeh and Nor Azwadi, Che Sidik and Abdul Malek, Adi Maimun and Nakisa, Mehdi (2014) Prediction of wind flow around high-rise buildings using RANS models. Applied Mechanics and Materials, 554 . pp. 724-729. ISSN 1660-9336

Belhocine, Ali and Abu Bakar, Abd. Rahim and Abdullah, Oday Ibraheem (2014) Structural and contact analysis of disc brake assembly during single stop braking event. International Journal of Automotive Engineering and Technologies . pp. 22-31. ISSN 2146-9067

Belhocine, Ali and Abu Bakar, Abd. Rahim and Abdullah, Oday Ibraheem (2014) Structural and contact analysis of disc brake assembly during single stop braking event. Transactions of the Indian Institute of Metals, 68 (3). pp. 403-410. ISSN 0972-2815

Belhocine, Ali and Abu Bakar, Abd. Rahim and Bouchetara, Mostefa (2014) Numerical modeling of disc brake system in frictional contact. Tribology in Industry, 36 (1). pp. 49-66. ISSN 0354-8996

Belhocine, Ali and Chong, Du Cho and Nouby, Mahdy and Yun, Bo Yi and Abu Bakar, Abd. Rahim (2014) Thermal analysis of both ventilated and full disc brake rotors with frictional heat generation. Applied and Computational Mechanics, 8 (1). pp. 5-24. ISSN 1802-680X

Che Sidik, Nor Azwadi and A., Rajab and A., Sofianuddin (2014) Four-sided lid-driven cavity flow using time splitting method of Adams-Bashforth scheme. International Journal of Automotive and Mechanical Engineering, 9 (1). pp. 1501-1510. ISSN 2229-8649

Che Sidik, Nor Azwadi and Jahanshaloo, L. and Safdari, A. (2014) The effect of mixed convection on particle laden flow analysis in a cavity using a Lattice Boltzmann method. Computers and Mathematics with Applications, 67 (1). pp. 52-61. ISSN 0898-1221

Che Sidik, Nor Azwadi and Khan, Aman Ali (2014) Simulation of flow over a cavity using multi-relaxation time thermal lattice Boltzmann method. Applied Mechanics and Materials, 554 . pp. 296-300. ISSN 1660-9336

Che Sidik, Nor Azwadi and Kianpour, Ehsan (2014) The effect of blowing ratio on film cooling effectiveness using cylindrical and row trenched cooling holes with alignment angle of 90 degrees. Mathematical Problems in Engineering, 2014 . ISSN 1563-5147

Che Sidik, Nor Azwadi and Razali, Siti Aisyah (2014) Two-sided lid-driven cavity flow at different speed ratio by lattice Boltzmann method. Applied Mechanics and Materials, 554 . pp. 675-679. ISSN 1660-9336

Che Sidik, Nor Azwadi and Salehi, Mehran (2014) Eulerian-Lagrangian numerical scheme for contaminant removal from different cavity shapes. Arabian Journal For Science and Engineering, 39 (4). pp. 3181-3189. ISSN 1319-8025

Che Sidik, Nor Azwadi and Tey, Wah Yen (2014) Reynolds number-strouhal number relationship for cylindrical bluff body with variation of aspect ratio in high Reynolds number. Jurnal Teknologi (Sciences and Engineering), 69 (3). pp. 125-128. ISSN 0127-9696

Chen, Wei Kew and Chong, Cheng Tung and Ng, Jo-Han and Tee, Boon Tuan and Mohd. Jaafar, Mohamad Nazri (2014) Flame and emission characteristics of a premixed swirl-stabilised burner. Jurnal Teknologi, 71 (2). pp. 43-48. ISSN 0127-9696

Chong, Cheng Tung and Kew, Chen Wei and Ng, Jo-Han and Tee, Boon Tuan and Mohd. Jaafar, Mohamad Nazri (2014) Effect of nitrogen dilution on the lean blowout limit and emissions of premixed propane/air swirl flame. Jurnal Teknologi, 71 (2). pp. 79-84. ISSN 0127-9696

Chong, Cheng Tung and Simone, Hochgreb (2014) Spray flame structure of rapeseed biodiesel and Jet-A1 fuel. Fuel, 115 . pp. 551-558. ISSN 0016-2361

Chukwuekezie, Christian Sunday and Ihueze, Christopher Chukwutoo and Idris, Jamaliah and Eyu, Gaius Debi (2014) Hygrothermal response of plant fibre reinforced composites. ARPN Journal of Engineering and Applied Sciences, 9 (3). pp. 336-341. ISSN 1819-6608

Dargi, Ahmad and Anjomshoae, Ali and Galankashi, Masoud Rahiminezhad and Memari, Ashkan and Md. Tap, Masine (2014) Supplier selection: a fuzzy-ANP approach. Procedia Computer Science, 31 . pp. 691-700. ISSN 1877-0509

Dawood, H. K. and Mohammed, Hussein A. and Munisamy, Kannan M. (2014) Heat transfer augmentation using nanofluids in an elliptic annulus with constant heat flux boundary condition. Case Studies in Thermal Engineering, 4 . pp. 32-41. ISSN 2214-157X

Dzulkifli, Mohd. Haziq and Yahya, Mohd. Yazid and Md. Akhir, Farhana Shakira and Abd. Majid, Rohah (2014) Development of rigid biocomposite polyurethane foam for load bearing application. Jurnal Teknologi (Sciences and Engineering), 68 (3). pp. 53-56. ISSN 2180-3722

Ee, Jonathan Yong Chung and Abdul Kader, Ab. Saman and Ahmad, Mohd. Zamani and Beng, Lokekeng (2014) Univariate throughput forecasting models on container terminal equipment planning. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 163-171. ISSN 0127-9696

Fadil, Nor Akmal and Saravanan, Govindachetty and Ramesh, Gubbala V. and Matsumoto, Futoshi and Ueda, Shigenori and Tanabe, Toyokazu and Hara, Toru and Ishihara, Shinsuke and Murakami, Hideyuki and Ariga, Katsuhiko and Abe, Hideki (2014) Synthesis and electrocatalytic performance of atomically ordered nickel carbide (Ni3C) nanoparticles. Chemical Communications, 50 (49). pp. 6451-6453. ISSN 1364-548X

Farahany, Saeed and Idris, Mohd. Hasbullah and Ourdjini, Ali (2014) Evaluations of antimony and strontium interaction in an Al-Si-Cu-Zn die cast alloy. Thermochimica ACTA, 584 . pp. 72-78. ISSN 0040-6031

Firdaus, Firdaus and Koto, Jaswar and Ammoo, Mohd. Shariff and Ishak, Iskandar Shah and Nofrizal, Nofrizal (2014) Review on aerodynamic characteristics of helicopter tail rotor propeller using quasi-continuous vortex lattice method. Journal of Ocean, Mechanical and Aerospace, Science and Engineering, 7 . pp. 8-17. ISSN 2354-7065

Fitriadhy, Ahmad and Yasukawa, Hironori and Yoneda, T. and Koh, Kho King and Maimun, A. (2014) Analysis of an asymmetrical bridle towline model to stabilise towing performance of a towed ship. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 151-156. ISSN 0127-9696

Ganjehkaviri, Abdolsaeid and Mohd. Jaafar, Mohammad Nazri (2014) Energy analysis and multi-objective optimization of an internal combustion engine-based CHP system for heat recovery. Entropy, 16 (11). pp. 5633-5653. ISSN 1099-4300

Ghadim, Mohammad Abbasgholipour and Mailah, Musa and Alasti, Behzad Mohammadi and Ghadim, Mehdi Abbasgholipour (2014) Simulation of MEMS capacitive thermal sensor based on tip deflection of a functionally graded micro-beam. Advanced Materials Research, 845 . pp. 340-344. ISSN 1022-6680

Gohari, Mohammad and Abdul Rahman, Roslan and Tahmasebi, Mona (2014) Prediction head acceleration from hand and seat vibration via artificial neural network model. NOISE, VIBRATION AND COMFORT, 471 . pp. 161-166. ISSN 1660-9336

Golshokouh, Iman and Samion, Syahrullail and Ani, Farid Nasir (2014) Influence of normal load and temperature on tribological properties of jatropha oil. Jurnal Teknologi, 71 (2). pp. 145-150. ISSN 0127-9696

Hashemi, Heidar and Md. Shaharoun, Awaluddin and Sudin, Izman (2014) A case-based reasoning approach for design of machining fixture. International Journal of Advanced Manufacturing Technology, 74 (4). pp. 113-124. ISSN 0268-3768

Hassan Ali, Yasir and Abdul Rahman, Roslan and Raja Hamzah, Raja Ishak (2014) Acoustic emission signal analysis and artificial intelligence techniques in machine condition monitoring and fault diagnosis: a review. Jurnal Teknologi (Sciences and Engineering), 69 (2). pp. 121-126. ISSN 2180-3722

Hassen, Nasir Salim and Che Sidik, Nor Azwadi and Hassan, Fargham (2014) Evaluation of spatial application accuracy of sensing-spraying system for variable rate application of oil palm trees. Advances in Environmental Biology, 8 (10). pp. 579-584. ISSN 1995-0756

Hassen, Nasir Salim and Che Sidik, Nor Azwadi and Md. Sheriff, Jamaluddin (2014) Advanced techniques for reducing spray losses in agrochemical application system. Life Science Journal, 11 (3). pp. 56-66. ISSN 1097-8135

Hoe, Pang Jung and Nik Mohd., Nik Ahmad Ridhwan (2014) Numerical prediction of blended wing body aerodynamic characteristics at subsonic speed. Jurnal Teknologi, 71 (2). pp. 65-69. ISSN 0127-9696

Hosseini, Seyed Ehsan and Abdul Wahid, Mazlan (2014) The role of renewable and sustainable energy in the energy mix of Malaysia: a review. International Journal of Energy Research, 38 (14). p. 1792. ISSN 0363-907X

Hosseini, Seyed Ehsan and Abdul Wahid, Mazlan and Ramesh, Farzad and Mohajeri, Hossein and Tajbakhsh, Bahram (2014) Combustion characteristics of inedible vegetable oil biodiesel fuels. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 157-162. ISSN 0127-9696

Hosseinia, Seyed Ehsan and Bagheria, Ghobad and Abdul Wahid, Mazlan (2014) Effects of hydrogen addition on the entropy generation of biogas conventional combustion. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 97-102. ISSN 0127-9696

Hudha, Khisbullah and Abd. Kadir, Zulkiffli and Jamaluddin, Hishamuddin (2014) Simulation and experimental evaluations on the performance of pneumatically actuated active roll control suspension system for improving vehicle lateral dynamics performance. International Journal of Vehicle Design, 64 (1). pp. 72-100. ISSN 0143-3369

Hussain, Sakhawat M.Shakil and Abdul Hamid, Mohd. Kameil and Mat Lazim, Ahmad Razimi and Abu Bakar, Abd. Rahim (2014) Brake wear particle size and shape analysis of non-asbestos organic (NAO) and semi metallic brake pad. Jurnal Teknologi, 71 (2). pp. 129-134. ISSN 0127-9696

Hyun, Cho Myung and Salleh, Suhaimi and Ahmad, Norhayati and Ourdjini, Ali and Hamzah, Esah (2014) Influence of carbon content on the mechanical properties of ultra-high strength of coated steel wire. Jurnal Teknologi (Sciences and Engineering), 69 (1). pp. 89-95. ISSN 2180-3722

Ishak, Mohamad Shaiful Ashrul and Mohd. Jaafar, Mohammad Nazri (2014) Experimental study on the production of CO-NO-HC emissions in the radial swirling flow combustion system. Jurnal Teknologi (Sciences and Engineering), 69 (2). pp. 45-48. ISSN 2180-3722

Ishak, Mohamad Shaiful Ashrul and Mohd. Jaafar, Mohammad Nazri (2014) Numerical analysis on the CO-NO formation production near burner throat in swirling flow combustion system. Jurnal Teknologi (Sciences and Engineering), 69 (2). pp. 71-77. ISSN 2180-3722

Ishak, Mohd Razmi and Abu Bakar, Abd. Rahim and Shamsudin, Subki and Maskak, Muhammad Husaini and Abdul Hamid, Mohd Kameil (2014) Experimental investigation of low speed disc brake judder vibration. Noise, Vibration and Comfort, 471 . pp. 25-29. ISSN 1660-9336

Ishak, Siti Amirah and Pangestu Djuansjah, Joy Rizki and Abdul Kadir, Mohammed Rafiq and Sukmana, Irza (2014) Angiogenesis in tissue engineering: from concept to the vascularization of scaffold construct. 2014 International Conference on Manufacturing, Optimization, Industrial and Material Engineering (MOIME 2014), 58 . ISSN 1757-8981

Israr, Haris Ahmad and Hongkarnjanakul, Natthawat and Rivallant, Samuel and Bouvet, Christophe (2014) Post-impact investigation of CFRP laminated plate. Jurnal Teknologi, 71 (2). pp. 71-78. ISSN 0127-9696

Isvandzibaei, M. R. and Jamaluddin, Hishamuddin and Raja Hamzah, Raja Ishak (2014) Effects of uniform interior pressure distribution on vibration of FGM cylindrical shell with rings support based on first-order theory subjected to ten boundary conditions. ACTA Mechanica, 225 (7). pp. 2085-2109. ISSN 0001-5970

Isvandzibaei, Mohammad Reza and Jamaluddin, Hishamuddin and Raja Hamzah, Raja Ishak (2014) Analysis of the vibration behavior of FGM cylindrical shells including internal pressure and ring support effects based on Love-Kirchhoff theory with various boundary conditions. Journal of Mechanical Science and Technology, 28 (7). pp. 2759-2768. ISSN 1738-494X

Jabal, Mohammed Hassan and Farid, Nasir Ani and Syahrullail, Samion (2014) The tribological characteristic of the blends of RBD palm olein with mineral oil using four-ball tribotester. Jurnal Teknologi (Sciences and Engineering), 69 (6). pp. 11-14. ISSN 0127-9696

Jafari, Hassan and Idris, Mohd. Hasbullah and Ourdjini, Ali (2014) An alternative approach in ceramic shell investment casting of AZ91D magnesium alloy: in situ melting technique. Journal of Materials Processing Technology, 214 (4). pp. 988-997. ISSN 0924-0136

Jafri, Mohd. Rohani and Hatami, Milad and Zahraee, Seyed Mojib and Khademi, Alireza and Shahpanah, Ataollah (2014) Evaluating the effect of main factors in manufacturing production line based on simulation experiment. Applied Mechanics and Materials, 606 . pp. 199-203. ISSN 1660-9336

Jahanshaloo, Leila and Che Sidik, Nor Azwadi and Kermani, Emad (2014) Application of the lattice Boltzmann method for fluid flow around complex geometry. Applied Mechanics and Materials, 554 . pp. 230-235. ISSN 1660-9336

Jahanshaloo, Leila and Che Sidik, Nor Azwadi and Salimi, Shahin and Safdari, Arman (2014) The use of thermal lattice Boltzmann numerical scheme for particle-laden channel flow with a cavity. Numerical Heat Transfer Part A-Applications, 66 (4). pp. 433-448. ISSN 1040-7782

Jamei, Saeed and Abdul Malik, Adi Maimun and Che Sidik, Nor Azwadi and Tofa, M. Mobassher and Mansor, Suhaimi and Priyanto, Agoes (2014) Ground viscous effect on 3D flow structure of a compound wing-in-ground effect. International Journal of Automotive and Mechanical Engineering, 9 (1). pp. 1550-1563. ISSN 2229-8649

Jamei, Saeed and Abdul Malik, Adi Maimun and Che Sidik, Nor Azwadi and Tofa, Mohammad Mobassher and Mansor, Shuhaimi and Priyanto, Agoes (2014) Static stability and ground viscous effect of a compound wing configuration with respect to reynolds number. Advances in Mechanical Engineering, 2014 . ISSN 1687-8132

Jamei, Saeed and Abdul Malik, Adi Maimun and Mansor, Shuhaimi and Che Sidik, Nor Azwadi and Priyanto, Agoes (2014) Experimental aerodynamic characteristics of a compound wing in ground effect. Journal of Fluids Engineering-Transactions of the Asme, 136 (5). ISSN 0098-2202

Jamei, Saeed and Maimun, Adi and Mansor, Shuhaimi and Priyanto, Agoes and Nor Azwadi, Nor Azwadi and Tofa, M. Mobassher (2014) Aerodynamic behavior of a compound wing configuration in ground effect. Jurnal Teknologi, 66 (2). pp. 21-27. ISSN 2180–3722

Jameia, Saeed and Abdul Malik, Adi Maimun and Tofa, M. Mobassher and Nor Azwadi, Nor Azwadi and Mansor, Shuhaimi and Priyanto, Agoes (2014) Static stability of a compound wing configuration in ground effect. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 159-162. ISSN 0127-9696

Koto, Jaswar and Priyanto, Agoes and Nekooei, Mohammadjavad (2014) Review on combustion control of marine engine by fuzzy logic control concerning the air to fuel ratio. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 103-106. ISSN 0127-9696

Jaswar, Jaswar and Siow, Chee Loon and Tiau, Kiu Ung and Abyn, Hassan (2014) Stability of mobile floating harbor container crane. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 133-139. ISSN 0127-9696

Jaswar, Koto and Junaidi, Abdul Khair (2014) Analysis of vortex-induced vibration of riser using Spalart-Almaras model. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 9-15. ISSN 0127-9696

Jaswar, Koto and Prayetno, E. (2014) Feasibility study of wing-in-ground for marine rescue operation. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 53-57. ISSN 0012-79696

Jaswar, Koto and Rashidi, Mehran G. M. and Abdul Maimun, Adi Maimun (2014) Tracking of ships navigation in the Strait of Malacca using automatic identification system. Developments in Maritime Transportation and Exploitation of Sea Resources, Vol 2 . pp. 721-725.

Jaswar, Koto and Siow, C. L. and Maimun, A. and Soares, C. Guedes (2014) Estimation of electrical-wave power in Merang shore, Terengganu, Malaysia. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 9-14. ISSN 0127-9696

Junaidi, Abdul Khair and Koto, Jaswar (2014) Parameters study of deep water subsea pipeline selection. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 115-119. ISSN 0127-9696

Kanesan, Gunasegaran and Mansor, Shuhaimi and Abdul-Latif, Ainullotfi (2014) Validation of UAV wing structural model for finite element analysis. Jurnal Teknologi, 71 (2). pp. 1-5. ISSN 0127-9696

Kazi, Suhail and Bashir, Muhammad Salman and Iqbal, Muhammad Munwar and Saleem, Yasir and Qureshi, M. Rizwan Jameel and Bashir, Raza (2014) Requirement change management in agile offshore development (RCMAOD). Science International, 26 (1). pp. 131-138. ISSN 1013-5316

Khademi, Alireza and Hosseini, Seyedeh Sabereh and Mirzapour, Seyed Ali and Jeddi, Alireza Rangraz and Mohd. Yusof, Noordin and Mohd. Rohani, Jafri and Khademi, Shahab (2014) Evaluating the effect of main factors in determining speed bump location based on Taguchi design of experiments. Jurnal Teknologi (Sciences and Engineering), 69 (3). pp. 99-104. ISSN 0127-9696

Khademi, Alireza and Mirzapour, Seyed Ali and Hosseini, Seyedeh Sabereh and Mohd. Yusof, Noordin (2014) The best location for speed bump installation using Taguchi and classical design of experiments. Quality Engineering, 26 (4). pp. 392-403. ISSN 0898-2112

Khairuddin, N. M. and Abd. Ghani, Mohd. Pauzi and Koto, Jaswar (2014) Experimental analysis on the mooring lines force behaviour of semi-submersible in regular waves. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 45-51. ISSN 0127-9696

Khaleghi, Mostafa and Hosseini, Seyed Ehsan and Abdul Wahid, Mazlan (2014) Emission and combustion characteristics of hydrogen in vortex flame. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 47-51. ISSN 0127-9696

Kherbeet, A. Sh H. and Mohammed, Hussein A. and Munisamy, Kannan M. and Salman, B. H. (2014) Combined convection nanofluid flow and heat transfer over microscale forward-facing step. International Journal of Nanoparticles, 7 (1). pp. 21-5. ISSN 1753-2515

Kherbeet, A. Sh. and Mohammed, Hussein A. and Salman, B. H. and Ahmed, Hamdi E. and Alawi, Omer A. (2014) Experimental and numerical study of nanofluid flow and heat transfer over microscale backward-facing step. International Journal of Heat and Mass Transfer, 79 . pp. 858-867. ISSN 0017-9310

Khodaei, Seyed Hossein and Galankashi, Masoud Rahiminezhad and Hassan, Adnan (2014) Priority analysis on the reliability parameters of an existing model. International Journal of Industrial Engineering and Management, 5 (2). pp. 77-84. ISSN 2217-2661

Kianpour, Ehsan and Che Sidik, Nor Azwadi (2014) Computational investigation of film cooling from cylindrical and row trenched cooling holes near the combustor end wall. Applied Mechanics and Materials, 554 . pp. 225-229. ISSN 1660-9336

Kianpour, Ehsan and Che Sidik, Nor Azwadi and Golshokouh, Iman (2014) Film cooling effectiveness in a gas turbine engine: a review. Jurnal Teknologi, 71 (2). pp. 25-35. ISSN 0127-9696

Konneh, Mohamed and Sudin, Izman and Padil, Mirza Emmil Dzahi and Roszat, Rosniza (2014) Surface roughness study of milled carbon fiber reinforced polymer (CFRP) composite using 4 mm 2-flute titanium aluminum nitride (TiAlN) coated carbide end mills. Advanced Materials Research, 887-88 . pp. 1101-1106. ISSN 1022-6680

Koto, Jaswar (2014) Absorption acid gas removal in liquefied natural gas process. Journal of Ocean, Mechanical and Aerospace -Science and Engineering-, 7 . pp. 24-28. ISSN 2354-7065

Koto, Jaswar and Amin, Amirul (2014) Performance of VLCC ship with podded propulsion system and rudder. Journal of Ocean, Mechanical and Aerospace -Science and Engineering-, 3 . pp. 18-24. ISSN 2354-7065

Koto, Jaswar and Junaidi, Abdul Khair and Hashim, M. H. (2014) Local buckling in end expansion of subsea pipelines. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 79-83. ISSN 0127-9696

Koto, Jaswar and Munirah, Munirah and Arief, Dodi Sofyan (2014) Occupational safety in production of traditional fishing vessels in Indonesia. Journal of Ocean, Mechanical and Aerospace -Science and Engineering-, 4 . pp. 7-12. ISSN 2354-7065

Koto, Jaswar and Muvariz, Mufti Fathonah and Siow, C. L. (2014) Fluid flow characteristic around round-shaped FPSO. Jurnal Mekanikal, 37 . pp. 47-63. ISSN 2289-3873

Koto, Jaswar and Nakisa, Mehdi (2014) Marine education and research development in Malaysia. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 91-95. ISSN 0127-9696

Koto, Jaswar and Priyanto, Agoes and Abdul Malik, Adi Maimun and Abd. Kader, Ab. Saman and Ahmad, Mohd. Zamani (2014) Study on wave buoy legged spider power device. Journal of Ocean, Mechanical and Aerospace -Science and Engineering-, 6 . pp. 8-16. ISSN 2354-7065

Kumar, Manasvi and Tiwari, Manoj Kumar and Wong, Kuan Yew and Govindan, Kannan and Kuah, Chuen Tse (2014) Evaluating reverse supply chain efficiency: manufacturer's perspective. Mathematical Problems in Engineering . ISSN 1024-123X

Kuppusamy, Navin Raja and Mohammed, Hussein A. and Lim, Chin Wai (2014) Thermal and hydraulic characteristics of nanofluid in a triangular grooved microchannel heat sink (TGMCHS). Applied Mathematics and Computation, 246 . pp. 168-183. ISSN 0096-3003

Leong, Mohd. Salman and Abdelrhman, Ahmed M. and Hee, Limmeng and Hui, K. H. (2014) Vibration analysis of multi stages rotor for blade faults diagnosis. Advanced Materials Research, 845 . pp. 133-137. ISSN 1022-6680

Lestari, Arfena Deah and Koto, Jaswar and Kader, A. S.A. (2014) Contribution of human factors to shipping safety. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 113-119. ISSN 0127-9696

Mahmood, Salwa and Jamil, Nor Hazrina and Mat Saman, Muhamad Zameri and Noordin, Mohd. Yusof (2014) Assessing sustainability performance of polymer processing: case study of hollow fiber membrane. Advanced Materials Research, 903 . pp. 365-370. ISSN 1022-6680

Mahmud, J. O. and Mohd. Ismail, Mohd. Shuisma and Mohd. Taib, Jamaludin (2014) Improving product classification through product family segregation. ARPN Journal of Engineering and Applied Sciences, 9 (5). pp. 775-782. ISSN 1819-6608

Mailah, Musa and Rosli, Rosmazi and Priyandoko, Gigih (2014) Active suspension system for passenger vehicle using active force control with iterative learning algorithm. WSEAS Transactions on Systems and Control, 9 . pp. 120-129. ISSN 2224-2856

Mansor, Shuhaimi and Dahalan, M. N. and Lee, Z. K. and Ali, A. (2014) Flow visualization and measurement of a synthetic jet actuator performance using PIV system. Jurnal Teknologi, 71 (2). pp. 13-17. ISSN 0127-9696

Masood, Ibrahim and Hassan, Adnan (2014) Bivariate quality control using two-stage intelligent monitoring scheme. Expert Systems with Applications, 41 (16). pp. 7579-7595. ISSN 0957-4174

Mat, Shabudin and Ishak, Irny Suzila and Mat Lazim, Tholudin and Mansor, Shuhaimi and Said, Mazuriah and Abd. Rahman, Abdul Basid and Mohd. Kamaludim, Ahmad Shukeri and Brossay, Romain (2014) Development of delta wing aerodynamics research in Universiti Teknologi Malaysia low speed wind tunnel. Advances in Mechanical Engineering . ISSN 1687-8132

Mat Darus, Intan Zaurah and Ahmed Suliman, Ali H. and Katimon, Ayob and Webster, Gumindoga (2014) Semi-distributed rainfall-runoff modeling utilizing ASTER DEM in Pinang catchment of Malaysia. Sains Malaysiana, 43 (9). pp. 1379-1388. ISSN 0126-6039

Mat Darus, Intan Zaurah and Mohd. Yatim, Hanim (2014) Self-tuning active vibration controller using particle swarm optimization for flexible manipulator system. WSEAS Transactions on Systems and Control, 9 . pp. 55-66. ISSN 2224-2856

Mat Ghani, Mohd. Firdaus and Fouladinejad, Nima and Mohd. Taib, Jamaludin and Dzakaria, Afandi (2014) Applications of cubic motion curve. Applied Mechanics and Materials, 606 . pp. 293-297. ISSN 1660-9336

Mat Saman, Muhamad Zameri (2014) Assessing the application of an extended framework of ERP implementation in SMES. International Journal of Current Life Science, 4 (9). pp. 7891-7898. ISSN 2249-1465

Mat Saman, Muhamad Zameri (2014) Relevance of ERP implementation and critical success factors in SMES of developing countries. International Journal of Scientific and Engineering Research, 5 (9). pp. 11-19. ISSN 2229-5518

Mazalan, Nor A. and A. Malek, Azlan and Abdul Wahid, Mazlan and Mailah, Musa (2014) Neural network modeling for main steam temperature system. Jurnal Teknologi (Sciences and Engineering), 69 (3). pp. 93-97. ISSN 0127-9696

Mazalan, Nor Azizi and A. Malek, Alisyn and Abdul Wahid, Mazlan and Mailah, Musa (2014) Primary superheater spray control valve modeling based on Levenberg-Marquardt learning algorithm. International Review of Mechanical Engineering, 8 (1). pp. 209-213. ISSN 1970-8734

Md. Saad, Amir Putra and Harun, Muhamad Noor and Syahrom, Ardiyansyah (2014) Study of wear prediction on total ankle replacement. Advanced Materials Research, 845 . pp. 311-315. ISSN 1022-6680

Mehdi, Nakisa and Abdul Malik, Adi Maimun and Yasser Mohamed, Ahmed and Jaswar, Jaswar and Priyanto, Agoes and Behrouzi, Fatemeh (2014) Numerical analysis of hydrodynamic propeller performance of LNG carrier in open water. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 85-89. ISSN 0127-9696

Mehdi, Nakisa and Abdul Malik, Adi Maimun and Yasser Mohamed, Ahmed and Steen, Sverre N. and Behrouzi, Fatemeh and Hassanzadeh, Reza A. and Ahmad Sabki, Ahmad F. (2014) Propeller effect on 3D flow at the stern hull of a LNG carrier using finite volume method. Applied Mechanics and Materials, 554 . pp. 566-570. ISSN 1660-9336

Mirzaei, Mahdi and Abdul Malik, Adi Maimun and Priyanto, Agoes and Fitriadhy, Ahmad (2014) Mooring pattern optimization using a genetic algorithm. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 189-193. ISSN 0127-9696

Moghadam, Ali Mokhtari and Kuan, Yew Wong and Piroozfard, Hamed and Derakhshan, Ali Asl and Hutajulu, Tiurmai Shanty (2014) Solving an industrial shop scheduling problem using genetic algorithm. Advanced Materials Research, 845 . pp. 564-568. ISSN 1022-6680

Moghadam, Ali Mokhtari and Piroozfard, Hamed and Ma'aram, Azanizawati and Mirzapour, Seyed Ali (2014) Solving a capacitated p-median location allocation problem using genetic algorithm: a case study. Advanced Materials Research, 845 . pp. 569-573. ISSN 1022-6680

Mohamed Ahmed, Yasser and Elbatran, A. H. and Shabara, H. M. (2014) Study of the effect of low profile vortex generators on ship viscous resistance. Journal of Ocean, Mechanical and Aerospace-Science and Engineering-, 3 . pp. 8-14. ISSN 2354-7065

Mohammed, Hussein A. and Om, Nurirmawati (2014) Three-dimensional numerical simulation of mixed convective heat transfer in a horizontal rectangular duct utilizing nanofluids. Advanced Materials Research, 1016 . pp. 738-742. ISSN 1022-6680

Mohammed, Mohammed Jawad and Mat Darus, Intan Zaurah (2014) Active vortex induced vibration controller and Neuro identification for marine risers. Journal of Theoretical and Applied Information Technology, 70 (1). pp. 153-162. ISSN 1992-8645

Mohammed, Mohammed Jawad and Mat Darus, Intan Zaurah (2014) PID controller for NARX and ANFIS models of marine pipe cylinder undergoes vortex induced vibration. Journal of Theoretical and Applied Information Technology, 66 (1). pp. 359-367. ISSN 1992-8645

Mohd. Ahyan, Nurul Aini and Samion, Syahrullail (2014) Study of alternative lubricants for cold extrusion process of A1100 pure aluminum. Jurnal Teknologi, 71 (2). pp. 139-143. ISSN 0127-9696

Abdul Hamid, Mohd. Kameil and Abu Bakar, Abd. Rahim and Stachowiak, Gwidon W. (2014) External hard particle size effect on changes in frictional performance and grit embedment during drag and stop mode braking. Jurnal Teknologi (Sciences and Engineering), 66 (3). pp. 65-73. ISSN 0127-9696

Mohd. Noor, Alias and Che Puteh, Rosnizam and Rajoo, Srithar (2014) Waste heat recovery technologies in turbocharged automotive engine? A review. Journal of Modern Science and Technology, 2 (1). pp. 108-119. ISSN 2201-6686

Mohd. Rashidi, M. and Idris, Mohd. Hasbullah (2014) The effects of solidification on the microstructure and mechanical properties of modified ductile Ni-resist iron with a high manganese content. Materials Science and Engineering A, 597 . pp. 395-407. ISSN 0921-5093

Mohd. Taib, Jamaludin and Abdul Jalil, Mohamad Kasim and Fouladinejad, Nariman (2014) Reduction of computational cost in driving simulation subsystems using approximation techniques. Proceedings - International Conference on Industrial Automation, Information and Communications Technology, IAICT 2014 . pp. 111-117.

Mohd. Yusof, Noordin and Mat Saman, Muhamad Zameri and Jiran, Nur Syamimi and Mahmood, Salwa (2014) Review on methodology for life cycle costing of membrane system for wastewater filtration. Advanced Materials Research, 845 . pp. 713-719. ISSN 1022-6680

Moinser, Mohd. Azuwan and Ahmad, Faiz and Sharif, Safian and Woo, Tze Keong (2014) Effects of twist drill point angle on thrust force and delamination factor in hybrid fiber composites drilling. Applied Mechanics and Materials, 564 . pp. 501-506. ISSN 1660-9336

Muhamad Said, Mohd. Farid and Aroussi, Abdelwahab (2014) Utilization of pulverised coal monitoring system for cleaner electricity generation. International Journal of Automotive and Mechanical Engineering, 9 (1). pp. 1588-1598. ISSN 2229-8649

Muhammad Ridhwan, Abd. Rahman and Vernin, Gregory and Abu Bakar, Abdul Rahim (2014) Preventing drum brake squeal through lining modifications. NOISE, VIBRATION and COMFORT, 471 . pp. 20-24. ISSN 1660-9336

Mursanto, Wahyu Budi and Sumeru, Kasni and Abdul Aziz, Azhar and Nasution, Henry (2014) Energy savings on automotive air conditioner using liquid-suction heat exchanger subcooler. Applied Mechanics and Materials, 554 . pp. 256-260. ISSN 1660-9336

Musa, Nur Amalina and Mansor, Shuhaimi and Ali, Airi H. (2014) Hardware in the loop of two rotors platform. Jurnal Teknologi, 71 (2). pp. 7-11. ISSN 0127-9696

Mustafa, Ammar and Martines-Botas, Ricardo and Pesiridis, Apostolos and Chiong, Meng Soon and Rajoo, Srithar (2014) Assessment of turbocharger turbine unsteady flow modelling methodology on engine performance. ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis, ESDA 2014, 1 .

Muvariz, Mufti Fathona and Afrizal, Efi and Djatmiko, Eko Budi and Murdjito, Murdjito and Jaswar, Koto (2014) Fracture of scantling support structure of gas processing module on FPSO. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 53-59. ISSN 0127-9696

Nasution, Henry and Munan, W. G. and Azhar, Abdul Aziz and Sumeru, Kasni and Abdul Latiff, Zulkarnain (2014) Energy analysis and compressor performance of refrigerator system using programmable logic control (PLC). Applied Mechanics and Materials, 554 . pp. 469-473. ISSN 1660-9336

Nazim, Engku Mohammad and Izman, Sudin and Ourdjini, Ali and Abu Bakar, Tuty Asma and Hassan, Mas Ayu (2014) Adhesion strength of HFCVD diamond coating on WC substrate seeded with diamond and different ratios of SiC powders. Advanced Materials Research, 845 . pp. 467-471. ISSN 1022-6680

Ng, Boon Chiang and Mat Daud, Intan Zaurah and Jamaluddin, Hishamuddin and Mohamed Kamar, Haslinda (2014) Application of adaptive neural predictive control for an automotive air conditioning system. Applied Thermal Engineering, 73 (1). pp. 1244-1254. ISSN 1359-4311

Ng, D. J. T. and Teng, Y. J. and Magee, A. R. and Ahmad Zukni, N. B. and Aramanadka, S. Bhat and Abdul Malik, A. M. and Abd. Kader, A. S. and Ismail, N. and Abdul Ghani, M. P. (2014) Riser VIV suppression device test. Proceedings of the Annual Offshore Technology Conference, 3 . pp. 1741-1752. ISSN 0160-3663

Nor Azwadi, Che Sidik and A. Sahak, Ahmad Sofianuddin and Ahmat Rajab, K. Y. (2014) Transient removal of contaminants in cavity of mixed convection in a channel by constrained interpolated profile method. Applied Mechanics and Materials, 554 . pp. 312-316. ISSN 1660-9336

Nordin, Nur Azmah and Farahany, Saeed and Ourdjini, Ali and Abubakar, T. and Hamzah, Esah (2014) Evaluation of the effect of bismuth on Mg2Si particulate reinforced in Al-20%Mg2Si in-situ composite. Advanced Materials Research, 845 . pp. 22-26. ISSN 1022-6680

Nur, Rusdi and Mohd. Yusof, Noordin and Izman, Sudin and Kurniawan, Denni (2014) Power demand calculations in turning of aluminum alloy. Advanced Materials Research, 845 . pp. 786-789. ISSN 1022-6680

NurIzzuddin, NurIzzuddin and Sunarsih, Sunarsih and Priyanto, Agoes and Rahimuddin, Rahimuddin (2014) Simulation on model performance of ship's diesel engine propulsion in calm water. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 153-158. ISSN 0127-9696

Othman, M. S. and Ahmad, Zaini (2014) Dynamic energy absorption performances of rain forest vehicle (RFV) under frontal impact. Jurnal Teknologi (Sciences and Engineering), 67 (3). pp. 123-129. ISSN 2180-3722

Pang, Zhen Ann and Ismail, Norasyikin and Nasir Ani, Farid (2014) The effect of flame temperature, nozzle position and swirl gas on microwave plasma flame. Jurnal Teknologi (Sciences and Engineering), 68 (3). pp. 133-137. ISSN 2180-3722

Phuman Singh, Amrik Singh and Mat Darus, Intan Zaurah (2014) Active roll control strategy using fuzzy logic control active suspension. WSEAS Transactions on Systems and Control, 9 (1). pp. 566-573. ISSN 1991-8763

Priyanto, Agoes and Abdullah, Mohd. Fahmi and Mehdi, N. and Rahimuddin, Rahimuddin (2014) Numerical structural analysis on a composite main wing of wig craft. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 109-113. ISSN 0127-9696

Priyanto, Agoes and Adi, Maimun and Kader, A. S. A. and Ismail, Nasrudin and Abdul Ghani, Mohamad Pauzi and Nur, Izzuddin and Jaswar, Koto (2014) Probability distribution of wave run up and dynamic response on a large volume semi-submersible. Ocean Engineering, 76 . pp. 52-64. ISSN 0029-8018

R., Rosliza and Wan Nik, Wan Mohd. NorsanI and Sudin, Izman (2014) Anti-corrosive performances of environmental friendly materials on Al-Mg-Si alloy. Advanced Materials Research, 1025-1 . pp. 668-671. ISSN 1022-6680

Rahimuddin, Rahimuddin and Abdul Malik, Adi Maimun and Gani, Pauzi A. (2014) Application of fuzzy logic controller to enhance the semi-SWATH performance in following seas. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 17-25. ISSN 0127-9696

Raja Mamat, Tengku Nur Azila and Mat Saman, Muhamad Zameri and Sharif, Safian (2014) The need of end-of-life vehicles management system in Malaysia. Advanced Materials Research, 845 . pp. 505-509. ISSN 1022-6680

Rashidi, M. and Koto, Jaswar (2014) Prediction of CO2 emitted by marine transport in Batam-Singapore channel using AIS. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 121-126. ISSN 0127-9696

Rashidi, Mohd. M. and Idris, Mohd. Hasbullah and Shayfull, Z. (2014) The effect of inoculation on properties of modified ductile Ni-resist alloy. Advanced Materials Engineering and Technology II, 594-59 . pp. 98-112. ISSN 1013-9826

Rezaei, Ghasem and Ansari, Majid and Zahraee, Seyed Mojib and Mohamed Shaharoun, Awaluddin and Memari, Ashkan (2014) A huiristic method for information scaling in manufacturing organizations. Jurnal Teknologi (Sciences and Engineering), 69 (3). pp. 87-91. ISSN 0127-9696

Rezvan, Pouyan and Azadnia, Amir Hossein and Mohd. Yusof, Noordin and Seyedi, Seyed Navid (2014) Sustainability assessment methodology for concrete manufacturing process: a fuzzy inference system approach. Advanced Materials Research, 845 . pp. 814-818. ISSN 1022-6680

Rosmi, Mohamad Saufi and Yusop, Mohd. Zamri and Kalita, Golap and Yaakob, Yazid and Takahashi, Chisato and Tanemura, Masaki (2014) Visualizing copper assisted graphene growth in nanoscale. Scientific Reports, 4 . ISSN 2045-2322

Roudsari, Arousha Haghighian and Wong, Kuan Yew (2014) A bi-objective stochastic single facility location model for a supermarket. International Journal of Services and Operations Management, 17 (3). pp. 257-279. ISSN 1744-2370

Rusdi, Nur and Mohd. Yusof, Noordin and Izman, S. and Kurniawan, Denni (2014) The effect of cutting parameters on power consumption during turning nickel based alloy. Advanced Materials Research, 845 . pp. 799-802. ISSN 1022-6680

Sadeghiamirshahidi, Narjes and Afshar, Jafar and Firouzi, Ali Reza and Syed Hassan, Syed Ahmad Helmi (2014) Improving the efficiency of manufacturing supply chain using system dynamic simulation. Jurnal Teknologi (Sciences and Engineering), 69 (2). pp. 117-119. ISSN 2180-3722

Saeed, Farahany and Ali, Ourdjini and Abu Bakar, Tuty Asma and Idris, Mohd. Hasbullah (2014) Role of bismuth on solidification, microstructure and mechanical properties of a near eutectic al-si alloys. Metals and Materials International, 20 (5). pp. 929-938. ISSN 1598-9623

Saeed, Farahany and Nordin, Nur Azmah and Ourdjini, Ali and Abu Bakar, Tuty Asma and Hamzah, Esah and Idris, Mohd. Hasbullah and Hekmat-Ardakan, Alireza (2014) The sequence of intermetallic formation and solidification pathway of an Al-13Mg-7Si-2Cu in-situ composite. Materials Characterization, 98 . pp. 119-129. ISSN 1044-5803

Safari, Habib and Sharif, Safian and Izman, S. (2014) Influence of cutting conditions on surface and sub-surface quality of high speed dry end milling Ti-6Al-4V. Jurnal Teknologi (Sciences and Engineering), 67 (3). pp. 131-136. ISSN 2180-3722

Samat, Khairul Fadzli and Hussein, Mohamed and Safizadeh, M. R. (2014) Analysis of single actuator for rehabilitation device of leg weakness. Applied Mechanics and Materials, 465-46 . pp. 1021-1025. ISSN 1660-9336

Samion, Syahrullail and Azmi, Aizat M. and Sapawe, Norzahir and Khalid, Amir (2014) Wear characterization of aluminum lubricated with palm olein at different normal load. Applied Mechanics and Materials, 554 . pp. 401-405. ISSN 1660-9336

Samion, Syahrullail and Daud, M. R. and Sapawe, Norzahir and Yahya, Azli (2014) An investigation of hard-on-soft sliding contact using palm fatty acid distillate. Advanced Research in Fluid Mechanics and Thermal Sciences, 2 (1). pp. 1-7. ISSN 2289-7879

Samion, Syahrullail and Daud, Md. Razak and Yahya, Azli and Sapawe, Norzahir and Mahmud, Nazriah and Hashim, Nor Liyana Safura and Kartiko, Nugroho (2014) Machining pits on the curvature surface cup using spark process. Jurnal Teknologi (Sciences and Engineering), 69 (3). pp. 129-132. ISSN 0127-9696

Samion, Syahrullail and Izhan, M. I. and Abdul Kadir, Mohammed Rafiq (2014) Tribological investigation of RBD palm olein in different sliding speeds using pin-on-disk tribotester. Scientia Iranica, 21 (1). pp. 162-170. ISSN 1026-3098

Samion, Syahrullail and Kamitani, Shunpei and Nakanishi, Kenji (2014) The effect of lubricant viscosity in cold work forward extrusion. Applied Mechanics and Materials, 554 . pp. 291-295. ISSN 1660-9336

Samion, Syahrullail and Kamitani, Shunpei and Shakirin, A. (2014) Tribological evaluation of mineral oil and vegetable oil as a lubricant. Jurnal Teknologi (Sciences and Engineering), 66 (3). pp. 37-44. ISSN 0127-9696

Samion, Syahrullail and Mohd. Ahyan, Nurul Aini (2014) Evaluation of paraffinic mineral oil as lubricant in cold work extrusion process. Applied Mechanics and Materials, 554 . pp. 327-331. ISSN 1660-9336

Samion, Syahrullail and Noorawzi, Nuraliza (2014) Experimental study on the effect of different speed using pin on disc tribotester. 4th Mechanical and Manufacturing Engineering, PTS 1 and 2, 465-46 . pp. 562-565. ISSN 1660-9336

Samion, Syahrullail and Norhakem, H. M. and Sapawe, Norzahir and Khalid, Amir (2014) The influence of normal load in wear resistance characteristic of palm fatty acid distillate. Applied Mechanics and Materials, 554 . pp. 286-290. ISSN 1660-9336

Samion, Syahrullail and Sapawe, Norzahir and M. D., Razak and Yahya, Azli (2014) Effect of surface modification of acetabular cup with embedded micro-pits on friction properties. American Journal of Mechanical Engineering, 2 (5). pp. 125-129. ISSN 2328-4110

Samion, Syahrullail and Zulhanafi, Paiman (2014) The oxidation effect of palm oil based lubricant using four - ball tribotester. Applied Mechanics and Materials, 554 . pp. 281-285. ISSN 1660-9336

Sapawe, Norzahir and Samion, Syahrullail and M. I., Izhan (2014) Evaluation on the tribological properties of palm olein in different loads applied using pin-on-disk tribotester. Jurnal Tribologi, 3 . pp. 11-29. ISSN 2289-7232

Saud, Safaa N. and Hamzah, Esah and Abubakar, T. and Bakhsheshi-Rad, H. R. and Zamri, Mohd. and Tanemura, Masaki (2014) Effects of Mn additions on the structure, mechanical properties, and corrosion behavior of Cu-Al-Ni shape memory alloys. Journal of Materials Engineering and Performance, 23 (10). pp. 3620-3629. ISSN 1059-9495

Saud, Safaa Najah and Hamzah, Esah and Abu Bakar, Tuty Asma and Farahany, Saeed (2014) Structure-property relationship of Cu-Al-Ni-Fe shape memory alloys in different quenching media. Journal of Materials Engineering and Performance, 23 (1). pp. 255-261. ISSN 1059-9495

Seyed Ali, Mirzapour and Wong, Kuan Yew and Hosseini, Seyedeh Sabereh and Shiripour, Saber (2014) Probabilistic formulation for emergency facility location in a divided area. Advanced Materials Research, 845 . pp. 527-531. ISSN 1022-6680

Seyedi, Seyed Navid and Rezvan, Pouyan and Akbarnatajbisheh, Saeed and Syed Hassan, Syed Ahmad Helmi (2014) Evaluating ARIMA-neural network hybrid model performance in forecasting stationary timeseries. Advanced Materials Research, 845 . pp. 510-515. ISSN 1022-6680

Sharifishourabi, G. and Sharifi, S. and Ayob, Amran and Yahya, M. Y. (2014) Tensile test machine for unsymmetrical materials. Experimental Mechanics, 54 (4). pp. 689-694. ISSN 1741-2765

Shinde, Sachin M. and Kalita, Golap and Sharma, Subash and Papon, Remi and Mohd. Yusop, Mohd. Zamri and Tanemura, Masaki (2014) Synthesis of a three dimensional structure of vertically aligned carbon nanotubes and graphene from a single solid carbon source. RSC Advances, 4 (26). pp. 13355-13360. ISSN 2046-2069

Shirdar, Mostafa Rezazadeh and Golshan, Abolfazl and Sudin, Izman and Ghodsiyeh, Danial (2014) The application of surface response methodology to the pretreatment of WC substrates prior to diamond coating. Journal of Materials Engineering and Performance, 23 (1). pp. 13-24. ISSN 1059-9495

Shokri Rad, Mozafar and Prawoto, Yunan and Ahmad, Zaini (2014) Analytical solution and finite element approach to the 3D re-entrant structures of auxetic materials. Mechanics of Materials, 74 . pp. 76-87. ISSN 0167-6636

Sian, Ang Yit and Abdul Malik, Adi Maimun and Priyanto, Agoes and Ahmed, Yasser Mohamed (2014) Assessment of ship-bank interactions on LNG tanker in shallow water. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 141-144. ISSN 0127-9696

Sian, Ang Yit and Abdul Malik, Adi Maimun and Priyanto, Agoes and Ahmed, Yasser Mohamed and Nakisa, Mehdi and Rahimuddin, Rahimuddin (2014) Numerical investigation for resistance characteristics of LNG carrier. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 101-107. ISSN 0127-9696

Siow, C. L. and Jaswar, Koto and Abby, Hassan and Khairuddin, N. M. (2014) Prediction of semi-submersible's motion response by using diffraction potential theory and heave viscous damping correction. Jurnal Teknologi (Sciences and Engineering), 69 (7). pp. 127-133. ISSN 0127-9696

Somia Alfatih, M. S. and Leong, Mohd. Salman and Lim, Meng Hee (2014) Application of bispectral analysis in vibration fault detection:a review. Applied Mechanics and Materials, 575 . pp. 464-468. ISSN 1660-9336

Sow, C. L. and Koto, Jaswar and Abyn, Hassan (2014) Semi-submersible heave response study using diffraction potential theory with viscous damping correction. Journal of Ocean, Mechanical and Aerospace -Science and Engineering-, 5 . pp. 23-29. ISSN 2354-7065

Sri Wuryanti, Sri Wuryanti and Poertadji, Suhardjo and Soegijono, Bambang and Nasution, Henry (2014) Experimental investigation on the thermal insulation properties of eic-cellulose. Applied Mechanics and Materials, 554 . pp. 322-326. ISSN 1660-9336

Sudin, Izman and Alipour, R. and Tamin, Mohd Nasir (2014) Estimation of charge mass for high speed forming of circular plates using energy method. Advanced Materials Research, 845 . pp. 803-808. ISSN 1022-6680

Sudin, Izman and Salleh, Sideq (2014) Effects of friction modifier additives on HDD substrate defects and surface topography during CMP. Advanced Materials Research, 845 . pp. 894-898. ISSN 1022-6680

Sulaiman, Mohd. Hafis and Mohd. Ridzuan, Mohd. Jamir and Mohamed, Alina Rahayu and Farahana, R. N. and Samion, Syahrullail (2014) An experimental investigation of palm pressed fibre waste as lubricant in strip drawing. Jurnal Teknologi (Sciences and Engineering), 66 (3). pp. 91-98. ISSN 0127-9696

Sulaimon, Shodiya and Abdul Aziz, Azhar and Darus, Amer Nordin and Nasution, Henry (2014) Empirical correlations for sizing adiabatic capillary tube using LPG as refrigerant in split-type air-conditioner. Advances in Applied Mechanics and Materials, 493 . pp. 99-104. ISSN 1660-9336

Sulaimon, Shodiya and Nasution, Henry and Abdul Aziz, Azhar and Abdul-Rahman, Abdul-Halim and Darus, Amer N. (2014) Taguchi method for development of mass flow rate correlation using hydrocarbon refrigerant mixture in capillary tube. Journal of Engineering and Technological Sciences, 46 B (2). pp. 141-151. ISSN 2337-5779

Sultan, A. Z. and Sharif, Safian and Kurniawan, Denni (2014) Examining the effect of various vegetable oil-based cutting fluids on surface integrity in drilling steel - a review. Advanced Materials Research, 845 . pp. 809-813. ISSN 1022-6680

Sumeru, Kasni and Martin, Luga and Ani, Farid Nasir and Nasution, Henry (2014) Energy savings in air conditioning system using ejector: an overview. Applied Mechanics and Materials, 493 . pp. 93-98. ISSN 1660-9336

Sumeru, Kasni and Nasution, Henry and Ani, Farid Nasir (2014) Thermodynamic analysis of ejector as an expansion device on split-type air conditioner using R410A as working fluid. Advances in Applied Mechanics and Materials, 493 . pp. 227-232. ISSN 1660-9336

Sumiwi, Agustin Dwi and Afrizal, Efi and Jaswar, Jaswar and Handayanu, Handayanu (2014) Offshore structure response due to ship collision on jacket legs. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 29-37. ISSN 0127-9696

Suprayogi, Dedy Triawan and Yaakob, Omar and Adnan, Faizul Amri and A. Ghani, Mohamad Pauzi and Ullah Sheikh, Usman Ullah Sheikh Izzat (2014) Field measurement of fishing boats generated waves. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 183-188. ISSN 0127-9696

Supriyo, Bambang and Tawi, Kamarul Baharin and Jamaluddin, Hishamuddin and Hussein, Mohamed (2014) Experimental study of electro-mechanical dual acting pulley continuously variable transmission ratio calibration. Jurnal Teknologi, 71 (2). pp. 121-127. ISSN 0127-9696

Syed Hassan, Syed Ahmad Helmi and Shahpanah, Ataollah and Gandomi, Nouredin and Zahraee, Seyedmojib and Hashemi, Ahmad (2014) Reduction of ship waiting time at port container terminal through enhancement of the tug/pilot machine operation. Jurnal Teknologi (Sciences and Engineering), 68 (3). pp. 63-66. ISSN 2180-3722

Syed Waheed, Ul Hasan and Farid Nasir, Ani (2014) Review of limiting issues in industrialization and scale-up of microwave-assisted activated carbon production. Industrial and Engineering Chemistry Research, 53 (31). pp. 12185-12191. ISSN 0888-5885

Tabatabaeikia, Seyedsaeed Saeed and Mohammed, Hussein A. and Nik-Ghazali, Nik Nazri and Shahizare, Behzad (2014) Heat transfer enhancement by using different types of inserts. Advances in Mechanical Engineering . ISSN 1687-8132

Talib, Mohamad Helmi and Abu Husain, Nurulakmar and Fauzi, Zaidi Farouk (2014) Preprocessing and solving finite element analysis for NVH prediction. Applied Mechanics and Materials, 471 . pp. 45-51. ISSN 1660-9336

Tamin, Mohd. Nasir and Wong, King Jye and Aivaddazeh, S. and Gong, X. J. (2014) R-curve modelling of mode I delamination in multidirectional carbon/epoxy composite laminates. Applied Mechanics and Materials, 606 . pp. 159-163. ISSN 1660-9336

Teo, Chee Loong and Atta, Madiha and Bukhari, Attaullah and Taisir, Mohamad and M. Yusuf, Md. Afendi and Idris, Ani (2014) Enhancing growth and lipid production of marine microalgae for biodiesel production via the use of different LED wavelengths. Bioresource Technology, 162 . pp. 38-44. ISSN 0960-8524

Thangavelu, Saravana Kannan and Ahmed, Abu Saleh and Ani, Farid Nasir (2014) Application of ANN to predict S.I. engine performance and emission characteristics fuelled bioethanol. Applied Mechanics and Materials, 554 . pp. 454-458. ISSN 1660-9336

Thangavelu, Saravana Kannan and Ahmed, Abu Saleh and Ani, Farid Nasir (2014) Bioethanol production from sago pith waste using microwave hydrothermal hydrolysis accelerated by carbon dioxide. Applied Energy, 128 . pp. 277-283. ISSN 0306-2619

Tofa, M. Mobassher and Abdul Malik, Adi Maimun and Ahmed, Yasser Mohamed and Jamei, Saeed and Abd. Kader, Ab. Saman and Abyn, Hassan (2014) Two degree of freedom vortex induced vibration tests of a riser model using spring bars. 4th Mechnical and Manufacturing Engineering, Pts 1 and 2, 465-46 . pp. 1339-1346. ISSN 1660-9336

Tofa, M. Mobassher and Abdul Malik, Adi Maimun and Ahmed, Yasser Mohamed and Jamei, Saeed and Priyanto, Agoes and Rahimuddin, Rahimuddin (2014) Experimental investigation of a wing-in-ground effect craft. Scientific World Journal . ISSN 1537-744X

Tofa, M. Mobassher and Abdul Malik, Adi Maimun and M. Ahmed, Yasser and Jamei, Saeed and Abyn, Hassan (2014) Experimental and numerical studies of vortex induced vibration on cylinder. Jurnal Teknologi (Sciences and Engineering), 66 (2). pp. 169-175. ISSN 0127-9696

Tri Putri, Nilda and Mohd. Yusof, Sha'ri and Irianto, Dradjad (2014) The Delphi hierarchy process-based study of quality engineering in Malaysia and Indonesia automotive companies. The TQM Journal, 26 (6). pp. 566-576. ISSN 1754-2731

Wahid, Mazlan Abdul and Hosseini, Seyed Ehsan (2014) Utilization of palm solid residue as a source of renewable and sustainable energy in Malaysia. Renewable and Sustainable Energy Reviews, 40 . pp. 621-632. ISSN 1364-0321

Wan Ab. Naim, Wan Naimah and Ganesan, Poo Balan and Sun, Zhonghua and Osman, Kahar and Lim, Einly (2014) The impact of the number of tears in patient-specific stanford type B aortic dissecting aneurysm: CFD simulation. Journal of Mechanics in Medicine and Biology, 14 (2). ISSN 0219-5194

Wan Ali, Wan Khairuddin and Long, Ang Kiang and Mohd. Jaafar, Mohammad Nazri (2014) Observation on solid propellant ignition using high speed camera: the effect of hot wire position on the combustion flame contour. Jurnal Teknologi, 71 (2). pp. 37-41. ISSN 0127-9696

Wan Hussin, Wan Nazdah and Hassan, Adnan and Halim, Abdurrachim H. and Zakaria, Zalmiyah (2014) Preliminary work towards development of a dynamic job shop scheduling model. Advanced Materials Research, 845 . pp. 682-686. ISSN 1022-6680

Wei, Huang and Mohd. Samin, Pakharuddin and Tawi, Kamarul Baharin and Supriyo, Bambang (2014) Frictional dissipation and mechanical efficiency analysis of clutched train engagement. Journal of Applied Science and Agriculture, 9 (18). pp. 238-244. ISSN 1816-9112

Wibowo Ndaruhadi, Paulus Yustinus Maria and Sharif, Safian and Kurniawan, Denni (2014) Experiment investigation of hole accuracy and surface roughness in femur bone drilling using different parameters. Advanced Materials Research, 845 . pp. 720-723. ISSN 1022-6680

Wong, Kuan Yew and Khodaei, Ghazal and Tiwari, Manoj Kumar (2014) Recycler selection using fuzzy AHP by considering sustainability. Advanced Materials Research, 845 . pp. 574-578. ISSN 1022-6680

Wong, Kuan Yew and Kuah, Chuen Tse (2014) Evaluating team performance using slack based data envelopment analysis. International Conference on Advanced Communication Technology, ICACT . pp. 1152-1157. ISSN 1738-9445

Wong, Wai Peng and Wong, Kuan Yew (2014) Synergizing an ecosphere of lean for sustainable operations. Journal of Cleaner Production, 85 . pp. 51-66. ISSN 0959-6526

Woo, Tze Keong and Ahmad, Faiz and Sharif, Safian and Moinser, Mohd. Azuwan (2014) Effects of drilling generated heat on damage factor in GFRP. Key Engineering Materials, 594-59 . pp. 661-665. ISSN 1013-9826

Woo, Tze Keong and Ahmad, Faiz and Sharif, Safian and Moinser, Mohd. Azuwan (2014) Evaluate of the effects of drilling with varying spindle speed using different thickness of GFRP on the damage factor. MATEC Web of Conferences, 13 . ISSN 2261-236X

Yahya, Mohd. Yazid and Ayob, Amran and Syed Hamzah, Syed Mohd. Saiful Azwan and Abdi, Behzad (2014) Quasi-static flexural and indentation behavior of glass fiber reinforced polymer composite sandwich panel. Advanced Materials Research, 845 . pp. 320-323. ISSN 1022-6680

Yahya, Mohd. Yazid and Ayob, Amran and Syed Hamzah, Syed Mohd. Saiful Azwan and Abdi, Behzad (2014) Quasi-static flexural and tensile behavior of glass fiber reinforced polymer. Advanced Materials Research, 845 . pp. 302-305. ISSN 1022-6680

Yanagihara, Masahiro and Mohd. Yusop, Mohd. Zamri and Tanemura, Masaki and Ono, Shingo and Nagami, Tomohito and Fukuda, Kentaro and Suyama, Toshihisa and Yokota, Yuui and Yanagida, Takayuki and Yoshikawa, Akira (2014) Vacuum ultraviolet field emission lamp utilizing KMgF3 thin film phosphor. APL Materials, 2 (4). ISSN 2166-532X

Yanagihara, Masahiro and Tsuji, Takayuki and Yusop, Mohd. Zamri and Tanemura, Masaki and Ono, Shingo and Nagami, Tomohito and Fukuda, Kentaro and Suyama, Toshihisa and Yokota, Yuui and Yanagida, Takayuki and Yoshikawa, Akira (2014) Vacuum ultraviolet field emission lamp consisting of neodymium ion doped lutetium fluoride thin film as phosphor. Scientific World Journal . ISSN 1537-744X

Yong, Tze Mi and Hamzah, Esah (2014) Effects of various seeding methods on multi-layered diamond coatings deposited via hot filament chemical vapor deposition. Advanced Materials Research, 845 . pp. 36-40. ISSN 1022-6680

Zahraee, Seyed Mojib and Hashemi, Ahmad and Abdi, Ahmed Ali and Shahpanah, Ataollah and Mohd. Rohani, Jafri (2014) Lean manufacturing implementation through value stream mapping: a case study. Jurnal Teknologi (Sciences and Engineering), 68 (3). pp. 119-124. ISSN 2180-3722

Zahraee, Seyed Mojib and Hatami, Milad and Bavafa, Ali Asghar and Ghafourian, Kambiz and Mohd. Rohani, Jafri (2014) Application of statistical Taguchi method to optimize main elements in the residential buildings in Malaysia based energy consumption. Applied Mechanics and Materials, 606 . pp. 265-269. ISSN 1660-9336

Zahraee, Seyed Mojib and Rezaei, Ghasem and Shahpanah, Ataollah and Chegeni, Ali and Mohd. Rohani, Jafri (2014) Performance improvement of concrete pouring process based resource utilization using Taguchi method and computer simulation. Jurnal Teknologi (Sciences and Engineering), 69 (1). pp. 17-24. ISSN 2180-3722

Zamberi, M. M. and Ani, Farid Nasir and Ghazali, S. H. (2014) The effects of alkaline catalysts in used frying oil biodiesel on the diesel engine performances. Applied Mechanics and Materials, 554 . pp. 449-453. ISSN 1660-9336

Zolfagharian, Ali and Noshadi, Amin and Khosravani, Mohammad Reza and Md. Zain, Mohd. Zarhamdy (2014) Unwanted noise and vibration control using finite element analysis and artificial intelligence. Applied Mathematical Modelling, 38 (9-10). pp. 2435-2453. ISSN 0307-904X

Zolpakar, Nor Atiqah and Mohd. Ghazali, Normah and Ahmad, Robiah (2014) Simultaneous optimization of four parameters in the stack unit of a thermoacoustic refrigerator. International Journal of Air Conditioning and Refrigeration, 22 (2). p. 1450011. ISSN 2010-1325

Conference or Workshop Item

Yusof, Siti Zahira and Fadil, Nor Akmal and Ourdjini, Ali and Abu Bakar, Tuty Asma (2014) Effect of tin coating thickness on tin whiskers formation and growth. In: Proceeding of 8th South East Asian Technical University Consortium (SEATUC) Symposium, 4-5 March, 2014, Skudai, Johor.

Abdullah, M. Adlan and Ani, Farid Nasir and Hassan, Masjuki (2014) Fuel system response of a common rail passenger car engine fuelled with palm oil biodiesel. In: Applied Mechanics & Materials.

Abdullah, Majid Adlan and Ani, Farid Nasir and Hassan, Masjuki (2014) Performance and emission of a common rail passenger car engine fuelled with palm oil biodiesel. In: International Conference on Advances in Mechanical and Manufacturing Engineering (ICAM2E), NOV 25-28, 2013, Kuala Lumpur, Malaysia.

Abuelnuor, A. A. A. and Saat, Aminuddin and Abdul Wahid, Mazlan and Saqr, Khalid and Mohd. Sies, Mohsin (2014) Flameless combustion of propane-air mixture in a laboratory scale burner. In: The 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Abyn, Hassan and Abdul Malik, Adi Maimun and Jaswar, Koto and Islam, Moni Rafiqul and Siow, C. L. and Bodaghi, Behnam (2014) TLP motion effect on semisubmersible motion. In: Offshore Technology Conference Asia: Meeting the Challenges for Asia's Growth, OTC ASIA 2014, 25-28 Mar,2014, Kuala Lumpur, Malaysia.

Adinoyi, Ayo Samuel and Mohd. Ghazali, Normah and Mansor, Shuhaimi (2014) Impact of adjacent building on outdoor ventilation around a layout of two buildings. In: 7th International Meeting on Advances in Thermofluids (IMAT), 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Ahmad Shafie, Noor Emilia and Mohamed Kamar, Haslinda and Kamsah, Nazri (2014) A CFD simulation of indoor air contaminant on ventilation system in a bus passenger compartment. In: The 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

El-Fawal, Mawahib Hassan and Mohd. Ghazali, Normah and Yaccob, Mohd. Shafiek (2014) Effects of the optimized resonator dimensions on the performance of the standing-wave thermoacoustic refrigerator. In: 7th International Meeting on Advances in Thermofluids (IMAT), 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Fakhir, Ammar and Saat, Aminuddin and Mat Lazim, Tholudin and Kareem, Zaid Sattar (2014) Numerical investigation of rectangular twisted hole on film cooling for gas turbine blades. In: The 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Hasan, Mohd. Faizal and Kawasaki, Yuki and Yokomori, Takeshi and Ueda, Toshihisa (2014) Characterization of flat sheet pd/ag membrane using pure hydrogen. In: Applied Mechanics and Materials, 31 Aug, 2014, Switzerland.

Kamaruzaman, Natrah and Saat, Aminuddin (2014) Characterization of a short microchannel device for surface cooling. In: The 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Kamsah, Nazri and Tamin, Mohd. Nasir and Mohamed Kamar, Haslinda (2014) Vapor pressure development in a FR4-CU composite structure during solder reflow. In: The 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Mansor, Shuhaimi and Nik Mohd., Nik Ahmad Ridhwan and Chan, Wei Chung (2014) Validation of CFD modeling and simulation of a simplified automotive model. In: 5th International Graduate Conference on Engineering, Science and Humanities (IGCESH 2014), 19-21 August, 2015, Skudai, Johor.

Mohamed Kamar, Haslinda and Kamsah, Nazri and Gan, Chee Ping (2014) Analysis of air and airborne particles movements in a hospital operating theater. In: The 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Mohamed Kamar, Haslinda and Kamsah, Nazri and Wong, Keng Yinn (2014) Field measurement of airborne particulate matters concentration in a hospital's operating room. In: The 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Mohd. Ghazali, Normah and Oh, Jong Taek and Ahmad, Robiah and Zolpakar, Nor Atikah (2014) Optimal frictional pressure drop and vapor quality relationship of ammonia and R22 in two-phase flow. In: 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Mohd. Ghazali, Normah and Pamitran, Agus Sunjarianto and Oh, Jong Taek and Ahmad, Robiah (2014) Effects of two-phase flow friction factor correlations on the optimal pressure drop-martinelli parameter pair in a mini-channel. In: 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Ng, David Jinq Tyng and Yih, Jeng Teng and Allan, Magee and Aramanadka, Shankar Bhat and Ahmad Zukni, NorBahrain and Abdul Malik, Adi Maimun and Abd. Kader, Ab. Saman and Ismail, Nasrudin and Abdul Ghani, Mohamad Pauzi (2014) Tandem riser VIV suppression fairing model test. In: 33rd International Conference on Ocean, Offshore and Arctic Engineering (ASME 2014), 8-13 June, 2014, California, USA.

Om, Nur Irmawati and Mohammed, Hussein A. (2014) Three-dimensional numerical simulation of mixed convective heat transfer in a horizontal rectangular duct utilizing nanofluids. In: 5th International Conference on Mechanical and Aerospace Engineering, ICMAE 2014, 18-19 Juny, 2014, Madrid; Spain.

Pamitran, Agus Sunjarianto and Khabibah, Ulfi and Mohd. Ghazali, Normah and Ahmad, Robiah and Saito, Kiyoshi (2014) Characteristics of two-phase flow heat transfer of R-22 and R-290 in horizontal circular small tube. In: 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Pang, Chi Loog and Abu Husain, Nurulakmar and Abdullah, Mohamed Ruslan (2014) Effect of strain rate on indentation behaviour of kenaf-based fibre metal laminates. In: The 5th International Graduate Conference on Engineering, Science and Humanities, 19-21 August, 2014, Skudai, Johor.

Permatasari, Rosyida and Mat Lazim, Tholudin and Sukarnoto, Tono and Supriyadi, Supriyadi (2014) Fluidization of gas-solid in atmospheric bubbling fluidized bed combustor. In: The 7th International Meeting on Advances in Thermofluids, 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Sarip, Shamsul and Hassan, Mohamad Zaki and Abdul Raman, Norazmein and Abdul Aziz, Sa’ardin and Md. Daud, Mohd. Yusof and Zainul Abidin, Mohd. Azman (2014) Renewable energy harness to uplift the prosperity of Royal Belum Forest. In: National Conference on Royal Belum 2014, 9-10 Dec, 2014, Perak, Malaysia.

Shahariar, G. M. Hasan and Hasan, Mohammad Rashedul (2014) Design and development of vertical axis wind turbine. In: 2014 9th International Forum on Strategic Technology (IFOST), 2014, Bangladesh.

Tofa, M. Mobassher and Abdul Malek, Adi Maimun and Ahmed, Yasser Mohamed and Jamei, Saeed and Abd. Kader, Ab. Saman and Abyn, Hassan (2014) Two degree of freedom vortex induced vibration tests of a riser model using spring bars. In: 4th International Conference on Mechanical and Manufacturing Engineering, ICME 2013, 17-18 Dec, 2013, Bangi, Putrajaya, Malaysia.

Zaidan, Husain and Mohd. Ghazali, Normah and Ahmad, Robiah (2014) Multi-layer micro channels system: interpretation and developments. In: 7th International Meeting on Advances in Thermofluids (IMAT), 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Zolpakar, Nor Atiqah and Mohd. Ghazali, Normah and Ahmad, Robiah (2014) Single-objective optimization of a thermoacoustic refrigerator. In: 7th International Meeting on Advances in Thermofluids (IMAT), 26-27 Nov, 2014, Kuala Lumpur, Malaysia.

Zolpakar, Nor Atiqah and Mohd. Ghazali, Normah and Ahmad, Robiah (2014) Single-objective optimization of a thermoacoustic refrigerator. In: Applied Mechanics and Materials, 26 Nov, 2014, Kuala Lumpur, Malaysia.

Thesis

Saud, Safaa Najah (2014) Influence of alloying elements and aging treatment on the phase transformation and shape memory behavior of Cu-Al-Ni shape memory alloys. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Omran, Abdoulhdi Amhmad Borhana (2014) Damage mechanics-based failure model for sheet metals under large plastic deformation. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Ab. Halim, Farah Salwani (2014) Establishing the prevalence and incidence of musculoskeletal disorders among welders in fabrication yard. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abd. Ghafar, Mohd. Fahri (2014) Design and development of a hand massage device for blood donation process. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abd. Majid, Noor Aishah (2014) Development of flexible assembly line with limited space allocation for manufacturing company. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abdi, Ahmed Ali (2014) Application of lean and six sigma with simulation in health care centre. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abdol Rahman, Mohd. Nasrull (2014) Development of an ergonomic risk assessment tool for work postures. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abdul Gafar, Liyana (2014) Supplier selection for EPCC Company of oil and gas industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abdul Ghani, Juliana (2014) The effect of compaction pressure and addition of silica on microstructure, thermal property and mechanical strength of polyurethane-silica RHA composite. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abdul Halim, Zulhelmi Alif (2014) Nanoscale microstructural characterization of aluminum and copper bilayer thin films deposited on silicon substrate using magnetron sputtering technique. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abdul Hamid, Mohd. Aidil Johari (2014) Product design improvement through design for assembly (DFA) and theory of inventive problem solving (TRIZ) of hair clipper. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abdulridha, Mundher Fadhil (2014) Finite element (FE) model of brake insulator in reducing brake squeal noise for motorcycles. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abed Shakir, Ali (2014) The effect of aging treatment on the microstructure and thermodynamic parameters of CuA1Ni-Mn shape memory alloys (SMAs). Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abubakar, Saidu Bello (2014) Numerical prediction of laminar nanofluid flow in rectangular microchannel. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Abyn, Hassan (2014) Hydrodynamic interactions and relative motions of floating bodies in waves. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Afripin, Mohammad Amirul Affiz (2014) Investigation of rollover performance for Malaysia bus superstructure. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Afroozmehr, Mohsen (2014) Application of system dynamic in selection of distribution centers through supply chain. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Ahmad, Mohd. Azuwan (2014) Practical ship weather routeing for liquefied natural gas carriers. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Ahmad Nizar, Nurul Kharmila (2014) Dust reduction in an electronic industry through TRIZ methodology. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Ahmed, Ahmed Mohammed Abdelrhman (2014) Blade faults diagnosis in multi stage rotor system by means of wavelet analysis. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Akbarzadeh, Mojtaba (2014) Derivation of finite element models of connected carbon nanotubes with heterojunctions. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Akbarzadeh, Mojtaba (2014) Derivation of finite elements models of connected carbon nanotubes with heterojunctions. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Alwerfally, Rehab M. O (2014) Risk assessment for construction supply chain. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Amani, Yasin (2014) Finite element simulation of arrays of hollow spheres structures. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Anuar, Muhamad Fauzi (2014) Programmable logic controller training module for positioning and sorting. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Arsad, Siti Syaleiza (2014) Unified constitutive models for deformation of thin-walled structures. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

As'arry, Azizan (2014) Intelligent active force control of human hand tremor using smart actuator. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Atan, Hood (2014) Estimation of occupational accident and accident prevention cost in wood based related industries. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Azadnia, Amir Hossein (2014) An integrated model for sustainable supplier selection and multi-period multi-product lot-sizing for packaging film industry in Iran. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Bakhtvar, Farzaneh (2014) Double population MRT LBM in an enclosure using nanofluid. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Basharudin, Ilyas Tufail (2014) Product development through design for assembly (DFA) and theory of inventive problem solving (TRIZ) methodologies of electric barbeque grill. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Bayat, Sajjad (2014) Method of productivity improvement through integration of analytical hierarchy process into theory of inventive problem solving. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Budianto, Aries (2014) Microcontroller based ratio control for electromechanical dual acting pulley continuously variable transmissions. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Chai, Teck Chaw (2014) Effect of surface preparations on the adhesion and corrosion behaviour of Zn-0.5Al coating on high carbon steel. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Chan, Shi Wei (2014) Computational analysis of nanofluids in heat exchanger. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Che Man, Mohd. Hasrizam (2014) Damage in laminated composites under low velocity impact. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Dehghan, Mohammad Mahdi Pir (2014) Investigation of the mechanical properties of carbon nanotubes, under the influence of imperfections. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Deljoumanesh, Hassan (2014) Integration of operating room planning and scheduling through managing uncertainty for emergency patients in orthopedic surgery. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Engku Abu Bakar, Engku Mohammad Nazim (2014) Surface treatment on tungsten carbide substrate prior to hot filament chemical vapour deposition diamond coating. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Esmaeil Abadi, Sayyed Mohsen Hashemi (2014) Forecasting the energy demand in Malaysia using genetic algorithm. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Esrafilian, Rasoul (2014) Slipping and falling due to contamination factors on ramp among workers in industries. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Fam, Kok Yeh (2014) Effect of groove at car park extraction system. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Fazeli, Alireza (2014) Hybrid Lattice-Boltzmann simulation of convective flow in a channel with extended surfaces. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Gholamkhasi, Arash (2014) Safety key performance indicators for SMEs. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Goh, Zhen Hwee (2014) Temperature effect of impulsive motion in an air floatation nozzle. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Gol Zardian, Mohsen (2014) Intelligent modelling and active vibration control of flexible manipulator. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Golroudbary, Saeed Rahimpour (2014) A system dynamics model in closed-loop supply chain by assessing sustainability. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Hadi, Muhamad Sukri (2014) Modelling and active control of flexible plate using evolutionary methods. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Hadzri, Edi Azali (2014) The effect of stenoses and irregular flow rates in human brain ventricular systems. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Hamidi, Ehsan (2014) Numerical simulation of tangential flow flameless combustion process. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Hashemzahi, Pooria (2014) The green supplier selection and order allocation in the supply chain under stochastic conditions. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Hashim, Ghasaq Adheed (2014) Numerical study of heat transfer enhancement in asphalt collector using CuO nanofluid. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Hassan, Mohd. Fahrul (2014) A framework for the sustainability evaluation of product configuration design. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Ho, Poo Mang (2014) Prediction of force in interference fits for cylindrical components. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Ibrahim, Mustafa Khaleel (2014) The effect of milling time on aluminum-silicon carbide composite. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Iranmanesh, Soudeh (2014) Dewaxing of ABS rapid prototype pattern for ceramic invesment casting of proximal humerus. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Iranmanesh, Soudeh (2014) Dewaxing of ABS rapid prototype pattern for ceramic investment casting of proximal humerus. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Ismail, Mohd. Nasiruddin (2014) Detecting and monitoring defects and damages on a pipeline using self-develop guided lamb wave system. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Jajarm, Arash Izadi (2014) Behavior of composite sandwich panel under quasi-static indentation load. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

James, Adeyemi Ademola (2014) A holistic backpack back pain model for prepubescent primary school children. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical.

Kamar Zaman, Syahrul Nizam (2014) Simulation analysis of an improved design for temporary crash barrier using plastic recycle material. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Kamrani, Mohsen (2014) An inventory model for deteriorating items with nonlinear holding cost. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Kanesan, Gunasegaran (2014) Structural design improvement of unmanned aerial vehicle wing. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Karandish, Ali (2014) Evaluating the surface properties of HA coating on titanium-aluminum substrate. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Khademi, Shahab (2014) Mechatronic and instrumentation of automotive air conditioning test rig. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Khanafiah, Khafri Izuan (2014) Catalyst pack for hydrogen peroxide monopropellant thruster. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Kheimeh Sari, Hirbod Maleki (2014) Evaluating the surface properties of HA coating on Co-Cr based alloy substrate. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Khodori, Ahmad Faidzal (2014) The study of limitations of several vehicles handling models. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Lafmejani, Masoud Pourasghar (2014) Evaluation of damage-based material models for carbon fiber-reinforced polymer composite laminate under mixed-mode bending. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Lee, Yoke Keen (2014) Computational investigation of heat transfer of nanofluids in domestic water heat exchanger. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mat Ghani, Mohd. Firdaus (2014) Integration of cubic motion and vehicle dynamic for yaw trajectory. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Md. Noor, Noor Rashidawani (2014) Technical and cost model for slipway development. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Md. Saad, Amir Putra (2014) Development of computational wear prediction on total ankle replacement. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mihanzadeh, Hooman (2014) Capital budgeting in an investment bank : a combined QFD, AHP and preemptive goal programming approach. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Moghadam, Maryam Sadrzadeh (2014) Ideal cycle analysis of a pulse detonation engine. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mohajeri, Hossein (2014) Combined convective heat transfer of nano fluids flow over triple backward facing step having baffle on its upper wall. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mohamad, Shuhaidi (2014) Experimental analysis of machining performance based on selected cutting parameters for smart CNC turning environment. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mohamed, Mohd. Shamshemun (2014) Association between ergonomic risk factors and musculoskeletal pain among fixie bike cyclists. Masters thesis, Universiti Teknologi Malaysia, Faculty of Management.

Mohammed, Ghaith Jasim (2014) Experimental investigation of brake judder noise. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mohd. Ani, Jaafar Sidek (2014) Evaluation of mechanical properties of alluminium filled epoxy compound for rapid tooling applications. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mohd. Saleh, Nazim (2014) Nickel phosphorus coated substrate micro-defect reduction through chemical mechanical planarization process optimization. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mohd. Shidek, Zulman (2014) Construction defect analysis of insulation panels for cargo tanks on liquified natural gas carriers. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mohd. Suri, Mohd. Syafiq (2014) Lubrication effect of metal-on-metal in hip joint replacement. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Moslemi, Navid (2014) The effect of current on characteristic for welded joint between 316 and 316L stainless steel including microstructure and mechanical properties. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mostakhdemin, Mohammad (2014) Numerical analysis of fatigue life prediction of trabecular bone respect to physiological activities (normal walking). Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Mozafari, Farzin (2014) Stress concentration in compressor blades with pits. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Muhamad Yussof, Siti Nurlaily (2014) Behaviour based safety implementation and comparison in a chemical manufacturing industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Muniandy, Sumitra (2014) System identifiction of an offshore flexible plate structure due to vortex induced vibration (VIV). Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Musa Zainal Abidin, Murni Farahin (2014) Characterisation of stainless steel 316L and palm stearin based binder by using metal injection molding (MIM) process. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Namin, Mahdi Hozhabri (2014) Wind tunnel test to investigate transition to turbulence on wind turbine airfoil. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Nejadi, Farhad (2014) Future trends of quality engineering and quality management implementation and practices. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Ng, Chee Chung (2014) Fluid flow and heat transfer analysis for power law fluids in circular cylinder. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Nordin, Haris Fadilla (2014) Effectiveness of homogenization equipment on very large crude carrier vessel. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Nya, Reza Manouchehry (2014) Stress intensity factor in c-ring shape. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Ooi, Ai Loon (2014) Effect of heat treatment on the interlayer and corrosion behavior of Zn and Zn-0.5%Al coated high carbon steel for marine application. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Othman, Mohamad Syauqy Amin (2014) Crash analysis of a rainforest vehicle (RFV) under frontal impact loading. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Peirovi, Soroush (2014) Cyclic strain characteristics of steel sheets under positive load ratio. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Philman Jong, Rudiyanto (2014) Prediction model for degeneration behaviour of mitral valve. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Pourhejazy, Seyed Pourya (2014) Optimization of a multi-objective-multi period traveling salesman problem with pickup and delivery using genetic algorithm. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Rabiee, Ali (2014) Integration of Taguchi's loss function with quality control charts. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Radzakrishnan, Loganathan (2014) System identification of offshore marine riser due to vortex induced vibration (VIV). Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Rahem, Monaf Ali (2014) Develop nanocomposite material of TiO2/Al2O3 using electrophoretic deposition. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Rajan, Sargeswara (2014) Pid controller for semi-active suspension system using magneto-rheological (MR) damper. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Razali, Nurhaulia (2014) Relationship between microstructure and mechanical property of nickel-aluminum bronze alloy solidified at different cooling rate and heat treated. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Razavykia, Abbas (2014) Effect of machining parameters and bismuth addition on al-20%mg2si machinability during dry turning. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Rival, Rival (2014) Machinability study of coated and uncoated carbide tools in drilling inconel 718. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Rosli, Mohd. Aidil (2014) Effects of chemical mechanical polishing (CMP) parameters on NIP/AL substrate surface characteristics. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Rosli, Muhamad Nurizad (2014) Fabrication of ceramic nozzle made from clay-alumina mixture. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Rosli, Muhamad Shafrilnizam (2014) Energy and economic analysis using boil-off gas onboard liquefied natural gas tanker vessel. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Saad, Mohd. Sazli (2014) Evolutionary optimisation and real-time self-tuning active vibration control of a flexible beam system. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Sabri, Intan Sabariah (2014) Numerical simulations on the effects of using ventilation fan on conditions of air inside a car passenger compartment. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Sadeghiamirshahidi, Narjes (2014) Development of a system dynamic model for aggregate planning in supply chain. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Saeid Hakim, Saeid Hakim (2014) Integration of aggregate production planning and short-term financial planning models. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Safiei, Wahaizad (2014) Performance evaluation of electrical discharge machining on stainless steel 316L using copper impregnated graphite. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Saili, Roziah Rohayah (2014) Establishing an ergonomics program in hard disc industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Salim, Norasikin (2014) Business process improvement (BPI) in an enterprise company. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Salimi, Shahin (2014) Numerical analysis of film cooling effectiveness using compound cooling holes at the end of gas turbine engine combustor. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Samsuri, Sakina (2014) Development of an investment analysis model for precast industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Sarabi, Arash Mazaheri (2014) Electrical discharge machining of siliconized silicon carbide using copper electrode. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Selamat, Ubaidullah (2014) Integrated Malaysian meteorological data atmospheric dispersion software for air pollutant dispersion simulation. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Shahbazi, Ehsan (2014) Optimization process for lightweight modular automotive components. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Shahpanah, Ataollah (2014) Improvement of ship berthing operation at port container terminal via discrete event simulation. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Shariatmadari, Shahab (2014) Work-related WMSDs assessment among video display terminal users. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Soh, Kian Jin (2014) Hemodynamics analysis for cosine shaped stenoses to blood flow behavior. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Soleimanynanadegany, Amin (2014) Product allocation to cross dock and warehouse using genetic algorithm. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Song, Jia (2014) Harnessing electrical energy from vibration of marine structure. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Suharyanti, Ike (2014) Financial analysis of wing in ground effect craft using monte carlo simulation. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Sutan, Mohd. Shahriman (2014) Springback behavior and surface quality of austenitic stainless steel plate during bending process. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Syed Talib, Syed Mohamad Najmi (2014) Flow modelling around propeller for a deep drafted vessel in very shallow water. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Taghizadeh, Hamid (2014) A case study of improving the tile manufacturing procsses using Lean Six Sigma. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Tahmasebi, Mona (2014) Intelligent active torque control for vibration reduction of a sprayer boom suspension system. PhD thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Tajbakhsh, Bahram (2014) Analysis of an industrial wind turbine to harness waste energy from air-conditioning chillers. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Tan, Mee Choo (2014) Ergonomics analysis of falling among workers at workplace. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Teh, Soo Chwen (2014) Structural analysis of coreless spoiler. Masters thesis, Universiti Teknologi Malaysia.

Waheed, Muneer Naji (2014) Disc brake squeal generation during dry and wet conditions. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Wan Hassan, Wan Anuar (2014) Numerical simulation on the effect of anastomosis and stenosis upon radiocephalic arteriovenous fistula. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Wong, Kam Khuan (2014) Neuro modelling and control of an automotive air conditioning system. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Yaacob, Amirrudin (2014) Safety on navigation in the straits of Malacca using Automatic Identification System (AIS) data. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Yii, Joy Sze Li (2014) In-vitro corrosion properties of quaternary Mg-Zn-Re-xCa alloys for biomedical applications. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Yusof, Siti Zahira (2014) Effect of environmental condition and nickel underlayer on whiskers formation in tin surface finish. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Zainal Abidin, Suzilawati (2014) CFD modelling on effect of different gasifying agents on syngas production from coal. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.

Zan, Umar Imraan (2014) Tow rope length and arrangement design for a towed ship. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering.