Items where Division is "Civil Engineering" and Year is 2008
Number of items: 247. AAb. Razak, Suraya (2008) Propagation of ship induced waves on to the Tanjung Piai coastline. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ab. Wahid, Zularisam (2008) Natural organic matter removal from surface water using submerged ultrafiltration membrane unit. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abd. Rahman, Norhan and Abu Hassan, Shukur (2008) Investigation of the hydraulic characteristics for portable rubbish & sediment trap. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Abd. Rahman, Ahmad Baharuddin and Ghazali, Abdul Rahim and Abd. Hamid, Zuhairi (2008) Comparative study of monolithic and precast concrete beam-to-column connections. Malaysian Construction Research Journal, 2 (1). pp. 42-55. ISSN 1985-3807 Abd. Rahman, Azilla (2008) Unethical conduct among professionals in the construction industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abd. Samal, Roslinda and Mohd. Ali, Nasty and Marsono , Abdul Kadir (2008) The optimum location of outrigger in reducing the along-wind and across-wind responses. Malaysian Journal of Civil Engineering, 20 (2). pp. 223-241. ISSN 1823-7843 Abd. Samat, Roslida (2008) The effectiveness of various structural system in reducing tall building response due to wind. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abd. Samat, Roslida (2008) The effectiveness of various structural systems in reducing tall building response due to wind. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abdol Mulok, Norleen Fariza (2008) The use of willingness-to-pay (WTP) method to identify potential for use of solar energy. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abdul Aziz, Waznah (2008) Tahap kefahaman dan kesesuaian pemeriksaan kesihatan projek sebagai alat pemantauan di Jabatan Kerja Raya. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering . Abdul Hamid, Abdul Rahim and Abd. Majid, Muhd Zaimi and Singh, Bachan (2008) Causes of accidents at construction sites. Malaysian Journal of Civil Engineering, 20 (2). pp. 242-259. ISSN 1823-7843 Abdul Hamid, Abdul Rahim and Abd Majid, Muhd. Zaimi and Singh, Bachan (2008) An overview of construction accidents in Malaysia. In: Issues In Construction Industry. Penerbit UTM , Johor, pp. 110-123. ISBN 978-983-52-0568-2 Abdul Hassan, Norhidayah and Hainin, Mohd. Rosli and Yaacob, Haryati (2008) Performance of hot mix asphalt using fine crumber. In: Highway Materials and Construction. Penerbit UTM , Johor, pp. 93-106. ISBN 978-983-52-0574-3 Abdul Hassan, Norhidayah and Hainin, Mohd. Rosli and Yaacob, Haryati and Mashros, Nordiana (2008) Performance of hot mix asphalt using fine crumb rubber. Geotechnical & Highway Engineering . Abdul Jalal, Muhamad Fikri (2008) Awareness of noise hazard from construction site. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abdul Malek, Marlinda (2008) Rainfall data in - filling model with expectation maximization and artificial neural network. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering . Abdul Malik, Ahmad Kamel (2008) Determination of periodic pavement rehabilitation treatment using Pavement Condition Assessment (PCA). In: Highway Materials and Construction. Penerbit UTM , Johor, pp. 37-48. ISBN 978-983-52-0574-3 Abdul Rahman, Noor Azah (2008) Comparison of bulk specific gravity by saturated surface dry method and vacuum sealing method. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abdul Wahab, Aiza Norwani (2008) Aircraft noise level study at the Sultan Ismail International Airport. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abdulgader Dow, Hamed (2008) Effects of air void and porosity on moisture damage of Malaysian specialty HMA. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abdullah, Arham and Sohaili, Johan and Azman, Azizul and Kassim, Mohamad Adam (2008) A methodological analysis of demolition works in Malaysia. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Abdullah, Shakila (2008) Tertiary treatment of palm oil mill effluent (POME) using hydrogen peroxide photolysis method. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abdullah, Zafri (2008) Concrete practice and defects during construction - case study. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abu, Aminudin and Oh, Jae-Eung and Lee, Jung Youn (2008) A characteristic of crankshaft behavior at the initial firing stage. In: Advances In Materials, Manufacturing and Materials Engineering. Penerbit UTM , Johor, pp. 18-41. ISBN 978-983-52-0563-7 Abu Bakar, Aniza (2008) Local labour : Prospects and challenges in construction industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abu Bakar, Faizah (2008) Customer satisfaction towards quality of workmanship in low cost housings in Klang Valley. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abu Bakar, Mohamad Noor Ropiah (2008) Punca dan impak perubahan kerja dalam projek milik UDA Holdings Berhad (UDA). Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Abu Bakar, Suhaimi and Gan, Chiew Leng (2008) Behaviour prediction of glued laminated timber beam made of different hardwood laminations using transformed section. In: Mechanical Properties And Bending Strength Theory For Malaysian Structural Timber. Penerbit UTM , Johor, pp. 83-93. ISBN 978-983-52-0567-5 Abu Bakar, Suhaimi and Mohamed, Zainai and Saleh, Abd. Latif (2008) Idealization of structural timber as a perfectly elasto-plastic material. In: Mechanical Properties and Bending Strength Theory for Malaysian Structural Timber. Penerbit UTM , Johor, pp. 24-35. ISBN 978-983-52-0567-5 Abu Bakar, Suhaimi and Mohamed, Zainai and Saleh, Abd. Latif (2008) An improved strain incremental formulation in boundary element method applied to a timber beam at the moment of failure. In: Mechanical Properties And Bending Strength Theory For Malaysian Structural Timber. Penerbit UTM , Johor, pp. 107-119. ISBN 978-983-52-0567-5 Abu Bakar, Suhaimi and Saleh, Abd. Latif (2008) Verification of weibull's theory of brittle fracture for local timber loaded in tension parallel to grain. In: Mechanical Properties And Bending Strength Theory For Malaysian Structural Timber. Penerbit UTM, Johor, pp. 1-10. ISBN 978-983-52-0567-5 Abu Bakar, Suhaimi and Saleh, Abd. Latif and Mohamed, Zainai (2008) An improvement of tresca’s yield criterion for the analysis of timber structure. In: Mechanical Properties And Bending Strength Theory For Malaysian Structural Timber. Penerbit UTM , Johor, pp. 94-106. ISBN 978-983-52-0567-5 Abu Bakar, Zaradiah (2008) Challenges face by Malaysian contractors in international ventures. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Adnan, Azlan and Hendriyawan, Hendriyawan and Selvanayagam, B. and Marto, Aminaton (2008) Development of seismic hazard maps of East Malaysia. In: Advances in Earthquake Engineering Application. Penerbit UTM , Johor, pp. 1-18. ISBN 978-983-52-0571-2 Adnan, Azlan and Ismail, Rozaina (2008) Database system and digital earthquake evaluation of buildings. In: Advances in Earthquake Engineering Application. Penerbit UTM , Johor, pp. 127-144. ISBN 978-983-52-0571-2 Adnan, Noor Azizah (2008) Challenges for improving the quality of the construction industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ahmad, Juraidah and Abdul Rahman, Mohd. Yusof and Hosasain, Mustaque and Hainin, Mohd. Rosli (2008) Evaluation of Malaysian asphaltic concrete mixture using superpave and marshall mix design method. In: Highway Materials and Construction. Penerbit UTM , Johor, pp. 49-62. ISBN 978-983-52-0574-3 Ahmad, Kamaruddin and Kassim, Khairul Anuar and Taha, Mohd. Raihan (2008) Geotechnical behaviour of electronically treated residual soils. In: Ground Improvement & Stabilization. Penerbit UTM , Johor, pp. 71-88. ISBN 978-983-52-0573-6 Ahmad, Muhammad Fiaz (2008) Horizontal shear stress contour mapping of composite slab by photostress method. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ahmad, Nordila (2008) Characterization of convective rain in Klang Valley, Malaysia. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ahmad, Rosli (2008) Best practices in safety management for conventional civil construction industry in Malaysia. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ahmad, Yusof (2008) Behaviour of strengthened timber beams using carbon fiber reinforced polymer. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Ahmed Eldagal, Omar Elmukhtar (2008) Study on the behaviour of high strength palm oil fuel ash (POFA) concrete. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Al Hassan, Altoum Alagab Al Amin (2008) The behavior of reinforce concrete beam with construction joint near the support. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Alashwal, Mohammed Taher (2008) Safety cost in pre-cast concrete construction. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering . Albshir Budiea, Ahmed Mokhtar (2008) Study on durability of high strength palm oil fuel ash pofa a concrete. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ali, Nazri and Rees, S. W. (2008) The influence of tree-induced suctions on slope stability. In: The International Conference in Geotechnical and Highway Engineering, Geotropika 2008. Universiti Teknologi Malaysia. ISBN 978-983-42613-4-4 Ali, Ahmad Zaki (2008) Causes and steps to minimize variations in construction projects. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ali, Md. Hazrat (2008) Conveyance efficiencies for different reservoir releases with and without existing river flow. In: Modeling Techniques of Rainfall and River Flow and Groundwater Contamination. Penerbit UTM , Johor, p. 107. Ali, Nazri (2008) Ground stabilization by tree induced suction. In: Ground Improvement & Stabilization. Penerbit UTM , Johor, pp. 89-105. ISBN 978-983-52-0573-6 Alkhaly, Yulius Rief (2008) Development of lightweight concrete using hollow spheres. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ang, Ting Guan (2008) The influence of the anchorage of independent bent-up bar on its shear capacity. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ann, See Peng (2008) Extreme growth behaviour of corrosion pit in hydrocarbon pipeline (case study of ø242.1mm pipeline). Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Anuar, Aznah Nor (2008) Development of aerobic granular sludge technology for domestic wastewater treatment in hot climates. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Apriansyah, Banny (2008) Platoon dispersion factors for trafic on single-carriageway roads. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Aris, Azmi and Ooi, Boon Siew and Kon, Suh Kee and Ujang, Zaini (2008) Tertiary treatment palm oil mill effluent using fenton oxidation. Malaysian Journal of Civil Engineering, 20 (1). pp. 12-25. ISSN 1823-7843 Aris, Azmi (2008) An overview of fenton oxidation process in water and wastewater treatment. In: Advances in Water and Wastewater Treatment Technologies. Penerbit UTM , Johor, p. 80. ISBN 978-983-52-0580-4 Asan, Amran (2008) Safety and health costing by medium and small class contractors. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Asmi, Ade (2008) Knowledge areas and information technology infrastructure capabilities in relation to construction project performance. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering . Asof, Marwan and Gofar, Nurly and Rahmatullah, Rahmatullah (2008) Response of clay shale to the variation of moisture content. Geotechnical & Highway Engineering . Azmi, Azharie Effenddy (2008) The properties and flexural behaviour of self compacting concrete using palm oil fuel ash and admixture. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Azmi, Nurdiana (2008) The development of matrix measurement guideline of collaborative teamwork environment in construction industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. BBandi, Shamsul Hadi (2008) Collaborative usage of ICT DBMS in construction cost control : the post contract perspectives. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Bashir, Abdullahi Abdullatif (2008) Simulation safety management of IBS construction. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Basri, Nor Iwani (2008) Critical success factors for IBS adoption in Malaysian construction industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Bateni, Norazlina (2008) Nearshore wave analysis of Batu Pahat river estuary. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. CChai, Erwin Pak Shin (2008) Capillary barrier effect on the response of residual slope to rainfall infiltration. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Che Puan, Othman and Hainin, Mohd. Rosli (2008) Existence of dilemma zones at signalised intersections. In: Sustainable Transportation Systems and Seaport Operations. Penerbit UTM , Johor, pp. 18-31. ISBN 978-983-52-0572-9 Chelladurai, Leena (2008) Comparison of guidelines on forensic engineering practices. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Chelliapan, Shreeshivadasan and Sallis, Paul (2008) Treatment of pharmaceutical wastewater by advanced oxidation process (AOP). In: Asian Water 2008 Conference -An International Conference on Water & Waste water, 2008, Kuala Lumpur, Malaysia. Chong, Ka Fung (2008) Collaborative site monitoring system for construction site. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Chong, Meng Hui (2008) Comparison of rainfall runoff characteristics and evapotranspiration in oil palm catchmernts. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. DDamayanti, Alia and Salim, Mohd. Razman and Ujang, Zaini (2008) COD fractionation and yield coefficient determination from palm oil mill effluent for activated sludge models. In: Advances in Water and Wastewater Treatment Technologies. Penerbit UTM , Johor, pp. 148-159. ISBN 978-983-52-0580-4 De' nan, Fatimah (2008) Lateral torsional buckling behaviour of trapezoid web profile section. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil engineering. Deris, Mohd. Azwanfadzli (2008) Contractor awareness on hazard of noise the contruction site workers. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Djati Utomo, Handojo (2008) Reducing copper toxicity by drinking coffee. In: WIT Transactions on Ecology and the Environment. WIT Press, United Kingdom, 199 -207. ISBN 978-184564114-6 EEl-Fadil, Mohamed El-Byhagi and Gofar, Nurly (2008) Stability analysis of unsaturated slopes subjected to rainfall infiltration. Geotechnical & Highway Engineering . El-Jelani, Barkah Ali (2008) Water resources management in Libya. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Eldina Fatimah, Eldina Fatimah (2008) Hydraulic performance of an artificial mangrove root system. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Esarwi, Ahmed Mohamed (2008) The effect of mix design system on stripping potential of hot mix asphalt mixture. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. FFikry, Muhammad (2008) Akaka (electronic document management system for government organization). Masters thesis, Universiti Teknologi Malaysia, Faculty of Computer Science and Information System. GGofar, Nurly (2008) Geosynthetic reinforced soil structure. In: Ground Improvement & Stabilization. Penerbit UTM , Johor, pp. 106-134. ISBN 978-983-52-0573-6 Gofar, Nurly (2008) The study on the development of saturation profile in soil slope. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Gofar, Nurly and Kassim, Azman (2008) Mechanics of rainfall infiltration through soil slope. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Gofar, Nurly and Lee, Min Lee and Kassim, Azman (2008) Instrumented soil column model for rainfall infiltration study. Geotechnical & Highway Engineering . ISSN 0128-0147 Gofar, Nurly and Mohamed, Rosdi (2008) Ground improvement by preloading and vertical drain. In: Ground Improvement & Stabilization. Penerbit UTM , Johor, pp. 53-70. ISBN 978-983-52-0573-6 Goh, Kee Keong and Osman, Mohd. Hanim (2008) Performance test on simply supported composite beam with TWP steel section. In: Analysis, Design and Performance of Steel Section With Trapezoid Web. Penerbit UTM , Johor, pp. 56-67. ISBN 978-983-52-0575-0 Gunalan, G. Jaganat (2008) Transient seepage trend through zoned earthfill dam. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. HHainin, Mohd. Rosli and Yaacob, Haryati and Woodside, Alan and Woodward, David (2008) Investigation on tyre/road noise using ulster load tyre road assimilator. Geotechnical & Highway Engineering . ISSN 0128-0147 Hamzani, Norfatiha (2008) The eco-labeling on sustainable roof materials. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Haron, Zaiton and Oldham, David and Yahya, Khairulzan and Zakaria, Rozana (2008) Application of A 2D Markovian approach to the modelling of sound propagation in streets. Malaysian Journal of Civil Engineering, 20 (2). 175 -187. ISSN 1823-7843 Haron, Zaiton and Oldham, David and Yahya, Khairulzan and Zakaria, Rozana (2008) A probabilistic approach for modelling of noise from construction site for sustainable environment. Malaysian Journal of Civil Engineering, 20 (1). pp. 58-72. ISSN 1823-7843 Haron, Zaiton and Yahya, Khairulzan and Oldham, David (2008) Construction site noise modelling using stochastic techniques. In: Issues in Construction Industry. Penerbit UTM , Johor, pp. 51-67. ISBN 978-983-52-0568-2 Harun, Sobri and Masimin, Masimin (2008) Extreme rainfall frequency analyses over the Banda Aceh Region. In: Stochastic Methods in Design Storm Estimations. Penerbit UTM , Johor, pp. 61-72. ISBN 978-983-52-0576-7 Hashim, Wardati (2008) The environmental effect on the cooling rate of hot mix asphalt pavement. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. IIbrahim, Zulkiflee and Abdul Latiff, Ab. Aziz and Ab. Halim, Azrul Hanif and Abu Bakar, Norlela and Subramaniam, Sivadas (2008) Experimental studies on mixing salt wedge estuary. Malaysian Journal of Civil Engineering, 20 (2). pp. 188-199. ISSN 1823-7843 Ibrahim, Izni S. and Kim, S. Elliott and Copeland, Simon (2008) Bending capacity of precast prestressed hollow core slabs with concrete toppings. Malaysian Journal of Civil Engineering, 20 (2). pp. 260-283. ISSN 1823-7843 Ibrahim, Izni Syahrizal and Osman, Mohd. Hanim and Usman, Fathoni (2008) Buckling analysis of plate girder with trapezoid web subjected to shear loading. In: Analysis, Design and Performance of Steel Section With Trapezoid Web. Penerbit UTM , Johor, pp. 1-11. ISBN 978-983-52-0575-0 Ibrahim, Zulkiflee and Abdul Latiff, Ab. Aziz and Ab. Halim, Azrul Hanif and Abu Bakar, Norlela and Subramaniam, Sivadas (2008) Experimental studies on mixing in a salt wedge estuary. Malaysian Journal of Civil Engineering, 20 (2). pp. 188-199. ISSN 1823-7843 Ibrahim, Zulkiflee and Abdul Latiff, Ab. Aziz and Subramaniam, Sivadas and Abu Bakar, Norlela and Ab. Halim, Hanif (2008) Flow experimental studies on mixing in a Salt Wedge Estuary. In: Problem Solving Through Experimental Hydraulics. Penerbit UTM , Johor, pp. 1-17. Ibrahim, Zulkiflee and Hashim, Noor Baharim and Abdul Latiff, Abd. Aziz and Halim, Herni and Mokhtar Kamal, Nurul Hana and Haron, Nuryazmeen Farhan (2008) Experimental investigation on the behaviour of thermal effluent in free surface flow. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Ismail, Mohamed ElGelany and Ismail, Mohamed Amri and Ohtsu, M. (2008) Non-destructive evaluation of corrosion activity in reinforced concrete slab. In: Proceedings of the 4th International Structural Engineering and Construction Conference, ISEC-4 - Innovations in Structural Engineering and Construction. Taylor & Francis Ltd, England, 1135 -1141. ISBN 978-041545755-2 Ismail, Mohammad (2008) Non-destructive evaluation of corrosion activity in reinforced concrete slab. In: Proceedings of the 4th International Structural Engineering and Construction Conference (ISEC-4). (In Press) Ismail, Mohammad and Mohamad Zin, Rosli and Ismail, Mohamed A. and Mohd. Yatim, Jamaluddin and Omar, Wahid (2008) Awareness among professionals in malaysian construction industries on reinforcement corrosion prevention and protection. Malaysian Journal of Civil Engineering, 20 (1). pp. 200-210. ISSN 1823-7843 Ismail, Rozaina (2008) The application of artificial neural network in seismic evaluation of buildings. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ismail, Zulhilmi and Shiono, Koji (2008) Flow rate and sediment transport characteristics compound meandering channels with vegetated floodplain. In: Problem Solving Through Experimental Hydraulics. Penerbit UTM , Johor, p. 91. Ithnin, Noorafidah (2008) Determination of mixing and compacting temperatures for hot mix asphalt. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. KKamaluddin, Noor Azreena (2008) Evaluation of stone mastic asphalt using palm oil fuel ash as filler material. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Kasim, Fauziah (2008) Compaction parameters’ estimation for ground improvement. In: Ground Improvement & Stabilization. Penerbit UTM , Johor, pp. 1-26. ISBN 978-983-52-0573-6 Kassim, Azman and Gofar, Nurly and Lee, Min Lee (2008) Numerical simulation of infiltration through unsaturated layered soil column. Malaysian Journal of Civil Engineering, 20 (2). pp. 211-222. ISSN 1823-7843 Khalid, Norazlan (2008) The geotechnical properties of pulverised fuel ash (PFA) as road embankment construction material. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Kong, Ling Kai (2008) Performance of mechanical coupler for connection of precsast concrete wall panels. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Kumaresan, Sivakumar (2008) A process engineering approach to the standardization of eurycomanone in eurycoma longifolia water extract. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. LLaw, Kim Hing (2008) Performance of multi-propped deep excavation in Kenny Hill formation. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Lee, Min Lee (2008) Influence of rainfall pattern on suction distribution and slope stability. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil engineering. Lee, Sid Hwa (2008) Failure of roof structure due to wind load. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Liew, Daniel Yu Chuan and Abdullah, Redzuan and Bakar, Khairul Bariyah (2008) Behaviour and load bearing capacity of composite slab enhanced with shear screws. Malaysian Journal of Civil Engineering, 20 (2). pp. 284-294. ISSN 1823-7843 Liew, Ming Hui (2008) Seismic effect on precast concrete structure for beam to column connection. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Liew, Shan Chin (2008) Characterization of natural fiber polymer compodites for structural application. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Liew, Shan Chin (2008) Pencirian sifat komposit polimer bergentian semula jadi untuk aplikasi struktur. Masters thesis, Universiti Teknologi Malaysia, Faculty of Mechanical Engineering. Liew, Vui Jen (2008) Analysis of extendable IBS steel truss. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Lim, Edward Kang Huang (2008) Parametric study for seepage flow pattern of pavement layers. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Lim, Siong Kang (2008) Engineering properties of resin grout as concrete repair material. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Lim, Siong Kang and Hussin, Mohd. Warid (2008) Effect of filler on strength development of epoxy grout. Malaysian Journal of Civil Engineering, 20 (1). pp. 38-46. ISSN 1823-7843 Lim, Victor Aik Jin (2008) Lean construction : knowledge and barriers in implementing into Malaysia construction industry. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ling, Jen Hua and Abd. Rahman, Ahmad Baharuddin and Mirasa, Abdul Karim and Abd. Hamid, Zuhairi (2008) Performance of cs-sleeve under direct tensile load: part 1: failure modes. Malaysian Journal of Civil Engineering, 20 (1). pp. 89-106. ISSN 1823-7843 Ling, Jeng Hua and Abd. Rahman, Ahmad Baharudin and Mirasa, Abdul Karim and Abd. Hamid, Zuhairi (2008) Performance of cs-sleeve under direct tensile load: part II: structural performance. Malaysian Journal of Civil Engineering, 20 (1). pp. 107-127. ISSN 1823-7843 Ling, Tung Chai and Md. Nor, Hasanan and Hainin, Mohd. Rosli and Chik, Abdul Aziz (2008) Laboratory performance of crumb rubber concrete block pavement. International Journal of Pavement Engineering . ISSN 1029-8436 Ling, Tung Chai and Md. Nor, Hasanan and Ming, Fai Chow (2008) Permanent deformation of concrete block pavements under highway accelerated loading. Road Engineering Association of Asia and Australia (REAAA) Journal, 15 (1). pp. 1-8. Ling, Tung Chai and Siong, Kang Lim and Hussin, Mohd. Warid and Zakaria, Fadhadli (2008) GGBFS as potential filler in polyester grout : flexural strength and toughness. Construction and Building Materials . pp. 1-9. Ling, Tung Chai and Md. Nor, Hasanan and Hainin, Mohd. Rosli (2008) Properties of crumb rubber concrete paving blocks with SBR latex. Road Materials and Pavements Design . pp. 1-10. Ling, Tung Chai (2008) Engineering properties and structural performance of rubberized concrete paving blocks. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Liua, Zhijun and Kingerya, William L. and Huddlestonb, David H. and Hossain, Faisal and Hashim, Noor Baharim and Kieffer, Janna M. (2008) Assessment of water quality conditions in the St Louis Bay watershed. Journal Of Environmental Science And Health Part A-Toxic/Hazardous Substances & Environmental Engineering , 43 . 468 -477. ISSN 1093-4529 Loh, Hsi Yoon (2008) Development of grouted splice sleeve and its performance under axial tension. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. MMamat, Rosmawati (2008) Evaluation of marshall properties of asphalt mixtures with aggregate gradations designed using the bailey method. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mansur, Mohammad A. and Maalej, Mohamed Amine and Ismail, Mohamed Amri (2008) Study on corrosion durability of ferrocement. ACI Materials Journal, 105 (1). 28 -34. ISSN 0889-325X Mansur, Shaiful Amri and Mohamad, Mohamad Ibrahim and Mohamad Zin, Rosli and Chooi, Chee Kong (2008) Knowledge transferring process in earthwork contracting firms. Malaysian Journal of Civil Engineering, 20 (1). pp. 30-39. ISSN 1823-7843 Mar Iman, Abdul Hamid (2008) Terms of Reference for a Desktop Study on Water Demand Management for an Industrial Area in Malaysia. FKSG, UTM. (Unpublished) Mar Iman, Abdul Hamid (2008) Terms of Reference for a Desktop Study on Water Demand Management for an Industrial Area in Malaysia. Water . (Unpublished) Masimin, Masimin (2008) Rainfall variability and design storms prediction using block peak method. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Masimin, Masimin and Harun, Sobri (2008) Analysis for annual maximum precipitation series for state of selangor using probability weighted moments. In: Stochastic Methods in Design Storm Estimations. Penerbit UTM , Johor, pp. 31-60. ISBN 978-983-52-0576-7 Md. Adnan, Nurul Huda (2008) Fish habitat assessment for river rehabilitation. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Md. Noor, Norhazilan and Yahaya, Nordin and Othman, Siti Rabe'ah (2008) The effect of extreme corrosion defect on pipeline remaining life-time. Malaysian Journal of Civil Engineering, 20 (1). pp. 47-57. ISSN 1823-7843 Md. Noor, Norhazilan (2008) Corrosion resistant steel bar. In: Corrosion of Steel in Concrete. Penerbit UTM , Johor, pp. 154-176. Md. Noor, Norhazilan (2008) Electrochemical method. In: Corrosion of Steel in Concrete. Penerbit UTM , Johor, pp. 1-21. ISBN 978-983-52-0570-5. Md. Nor, Hasanan and Abd. Muti, Abd. Aziz and Che Puan, Othman and Chik, Abdul Aziz and Ismail, Che Ros and Ling, Tung Chai and Mudiyono, Rachmat (2008) Development of new technologies for interlocking concrete block pavement (ICBP). Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Md. Tahir, Mahmood and Sulaiman, Arizu (2008) Standardisation of partial strength connections of extended end-plate connections for trapezoid web profiled steel sections. Malaysian Construction Research Journal, 2 (1). pp. 14-41. ISSN 1985-3807 Md. Tahir, Mahmood and Sulaiman, Arizu (2008) Standardisation of partial strength connections of extended end–plate connections for trapezoid web profiled steel sections. Malaysian Construction Research Journal, 2 (1). pp. 30-44. ISSN 1985-3807 Md. Tahir, Mahmood and Sulaiman, Arizu and Bakri, Ahmadon and Tan , Cher Siang and Shek, Poi Ngian and Wong, Kah Leong (2008) New concept of construction method for foundations system using cold-formed steel section. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Md. Yatim, Mohd. Yazmil (2008) Finite element investigation of strength of semi - rigid steel joints. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohamad, Edy Tonnizam and Komoo, Ibrahim and Kassim, Khairul Anuar and Gofar, Nurly (2008) Influence of moisture content on the strength of weathered sandstone. Malaysian Journal of Civil Engineering, 20 (1). pp. 137-144. ISSN 1823-7843 Mohamad, Irma Noorazurah (2008) Risk in sediment-impacted detention pond analysis using monte carlo simulation at Iskandar Malaysia (Nusajaya), Johor. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohamad, Mohamad Ibrahim and Madon, Zulkifli and Zin, Rosli and Mansur, Shaiful Amri (2008) Clarity and improving level of understanding of contract documentation. Malaysian Journal of Civil Engineering, 20 (1). pp. 128-136. ISSN 1823-7843 Mohamad, Mohamad Ibrahim and Yahya, Khairulzan (2008) Applying CE to construction. In: Issues In Construction Industry. Penerbit UTM , Johor, pp. 1-16. ISBN 978-983-52-0568-2 Mohamad, Mohd. Fauzi (2008) Physical flood modelling evaluation of river meandering channel in tidal effected reach. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohamad Yatim, Jamaludin and Ho, Shu Feng and Tapsir, Siti Hamisah (2008) Effect of fibre orientations on single-lap bolted joint of pultruded GFRP plates under tensile loading. In: Advanced Composite Materials Properties and Applications. Penerbit UTM , Johor, pp. 85-99. ISBN 978-983-52-0569-9 Mohamad Yatim, Jamaludin and Mohamed, Zainai and Tapsir, Siti Hamisah (2008) Behaviour of pultuded GFRP composites under tensile and compressive loading. In: Advanced Composite Materials Properties and Applications. Penerbit UTM , Johor, pp. 40-57. ISBN 978-983-52-0569-9 Mohamad Yatim, Jamaludin and Mohamed, Zainai and Tapsir, Siti Hamisah (2008) Environmental effects on mechanical properties of GFRP Composites : an overview. In: Advanced Composite Materials Properties and Applications. Penerbit UTM , Johor, pp. 100-124. ISBN 978-983-52-0569-9 Mohamad Zin, Rosli and Tan, Caren Cai Loon (2008) A neural model for predicting the time performance of traditional general contract (TGC) project. Malaysian Journal of Civil Engineering, 20 (1). pp. 26-37. ISSN 1823-7843 Mohamad Zin, Rosli (2008) Construcability in construction. In: Issues in Construction Industry. Penerbit UTM , Johor, pp. 17-34. ISBN 978-983-52-0568-2 Mohamad Zin, Rosli and Mohamad, Mohamad Ibrahim and Mansur, Shaiful Amri and Chan Donald, Bing Tee (2008) Guidelines for the preparation and submission of work schedule for construction project. Malaysian Journal of Civil Engineering, 20 (2). pp. 145-159. ISSN 1823-7843 Mohamed, Rosdi and Zakaria, Fadhadli and Gofar, Nurly (2008) Performance of ground improvement by precompression and vertical drain. Geotechnical & Highway Engineering . Mohamed, Rosdi (2008) Performance of ground improvement by precompression and vertical drain. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohamed Balrwin, Rafeg Ali (2008) Highway interchange simulation. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohammad Ismail, Mohammad Ismail and S. Sergi, George (2008) Electrochemical chloride extraction treatment on chloride contaminated concrete. In: Corrosion of Steel in Concrete. Penerbit UTM , Johor, pp. 128-153. Mohammadpour, Atefeh (2008) Simulation modeling in construction industry for IBS implemention. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohd. Anuar, Norzana (2008) Performance of perforated piles as a wave attenuator. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohd. Fadhil, Mohd. Fadhil and Ujang, Zaini and Van Loosdrecht, Mark and Ahmad, Mohd. Azlan (2008) Polyhydroxyalkanoates (PHAs) production from saponified sunflower oil in mixed cultures under aerobic condition. Jurnal Teknologi (48F). pp. 1-19. ISSN 0127-9696 Mohd. Fuad Ngo, Juliza (2008) Risk assessment using pool fire and health index analysis at bioenergy plant. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohd. Haniffah, Mohd. Ridza (2008) Finite element formulation for free vibration of composite beams. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohd. Hashim, Mohd. Hisbany and Mohd.Sam, Abdul Rahman and Husin, Mohd.Warid and Abu Hassan, Shukur (2008) Performance of externally bonded reinforced concrete structures using carbon fibre reinforced polymer in tropical climate. In: Advanced Composite Materials Properties and Applications. Penerbit UTM , Johor, pp. 73-84. ISBN 978-983-52-0569-9 Mohd. Radzuan, Nor Amin (2008) The challenges in international construction project with regard to safety compliance and cross cultural management. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohd. Rodzi, Rodziana (2008) Faktor penghalang perlaksanaan pengurusan kualiti menyeluruh (TQM) menurut perspektif kontraktor. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering . Mohd. Said, Mohd. Ismid and Abdul Razak, Abdul Syukur and Ibrahim, Zaharah and Salim, Mohd. Razman and Anuar, Aznah Nor and Sulaiman, Suryati (2008) Application of Treated Sewage Effluent for Watering of Public Park and Landscape Garden. In: Advances in Water and Wastewater Treatment Technologies. Penerbit UTM , Johor, p. 70. ISBN 978-983-52-0580-4 Mohd. Said, Mohd. Ismid and Abdul Razak, Abdul Syukur and Ibrahim, Zaharah and Salim, Mohd. Razman and Nor Anuar, Aznah and Sulaiman, Suryati (2008) Microbial assessment of landscape garden watering using treated sewage effluent. In: Advances in water and wastewater treatment technologies. Penerbit Universiti Teknologi Malaysia, pp. 1-15. ISBN 978-983-52-0580-4 Mohd. Yusof, Mohd. Badruddin and Othman, Fadil (2008) Factors affecting municipal solid waste generation : a case study in Southern Peninsula of Malaysia. In: Waste Book. Penerbit UTM , Johor. Mohd. Zainal, Ahmad Mawardi (2008) Incorporating sustainable concept to improve architectural design. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mohd. Zin, Zainiah (2008) A stochastic approach to designing stormwater detention pond. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Mokhtar, Kasypi and Che Puan, Othman and Abd. Hamid, Saharuddin (2008) Containerisation and intermodality : a case of Malaysian Port. In: Sustainable Transportation Systems and Seaport Operations. Penerbit UTM , Johor, p. 162. ISBN 978-983-52-0572-9 Mosmin, Zairulakmar (2008) Self assessment tool for chemical health risks in the work environment. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Muhamad Ali, Mohd. Zaharifudin (2008) Evaluation of the hydrodynamic and sedimen transport model using environmetal fluid dynamic code. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Musta, Baba and Kassim, , Khairul Anuar and Salim, Mohd. Razman (2008) Engineering properties of lime stabilised mining waste from Sabah, Malaysia. In: Waste Book. Penerbit UTM , Johor. Mustaffar, Mushairry and Puan, O. C. and Ling, Tung Chai (2008) Automated pavement imaging program (APIP) for pavement cracks classification and quantification – a photogrammetric approach. In: XXIth ISPRS Congress, Society of Photogrammetry and Remote Sensing, 3th - 11th July 2008, Beijing, China. NN., Ali and S. W., Rees (2008) Preliminary analysis of tree-induced suctions on slope stability. Journal of Civil Engineering and Architecture . pp. 811-816. ISSN 1934-7359 Negrat, Walid Ayad M. (2008) Modeling of TSUNAMI propagation in Melaka Straits. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ng, Ping Chew (2008) Comparison of creep and shrinkage using different code of practice. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ng, Zee Leong and Osman, Mohd. Hanim (2008) Local flange buckling of trapezoid web profile. In: Analysis, Design and Performance of Steel Section With Trapezoid Web. Penerbit UTM, Johor, p. 121. ISBN 978-983-52-0575-0 Ni'am, Moh Faiqun and Othman, Fadil and Sohaili, Johan and Fauzia, Aulfa (2008) Electrocoagulation technique for removal of COD and turbidity to improve wastewater quality. Ultrapure Water, 25 (3). pp. 36-43. ISSN 0747-8291 Nor Anuar, Aznah (2008) Development of aerobic granular sludge technology for domestic wastewater treatment in hot climates. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. OOmar, Wahid and Makhtar, Ahmad Mahir and Tan, Pui Lai and Omar, Roslina and Ng, Ming Kwong (2008) Creep, shrinkage and elastic modulus data of Malaysian concrete. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Omar, Qistina (2008) Recovery and reuse of iron from solar fenton sludge in treating palm oil mill secondary effluent (POMSE). Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Omar, Wahid and Tan, Pui Lai and Lee, Poh Huat and Omar, Roslina (2008) Improved prediction of pre-camber of post-tensioned prestressed I-beam. The Journal of the Institution of Engineers, Malaysia, 69 (1). pp. 32-37. ISSN 0126-513X Ooi, Chow Ern (2008) Effect of lamination on rock properties under uniaxial loading. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Osman, Mohd. Hanim and Kasim, Fauziah and Saim, A. Aziz (2008) Field capacity of steel pile with corrugated web surface. In: Advanced Composite Materials Properties and Applications. Penerbit UTM , Johor, pp. 82-98. ISBN 978-983-52-0575-0 Osman, Mohd. Hanim and Kirasa, Abdul Karim and Abd. Rahman, Ahmad Baharuddin (2008) Solution to problems in structural steel design to BS 5950:Part 1: 2000. Penerbit UTM, Skudai, Johor Bahru. ISBN 978–983–52–0482–1 Osman, Mohd. Hanim and Saleh, Abd. Latif and Saim, A. Aziz and Ween, Fong Shiaw (2008) Analytical study on secondary bending moment in trapezoid web beam. In: Analysis, Design and Performance of Steel Section With Trapezoid Web. Penerbit UTM , Johor, pp. 26-42. ISBN 978-983-52-0575-0 Osman, Mohd. Hanim and Tan, Cher Siang and Salleh, Abd. Latif (2008) Buckling analysis of column with trapezoid web. In: Analysis, Design and Performance of Steel Section With Trapezoid Web. Penerbit UTM , Johor, pp. 43-55. ISBN 978-983-52-0575-0 Osman, Noor Azahar (2008) Analisis kecacatan semasa pembinaan dan kualiti bangunan di celcom. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Othman, Ahmad Mazlan (2008) A comparison between blast debris from lightweight and normal concrete structure. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Othman, Fadil (2008) Adsorption process using carbon made of oil palm agricultural waste. In: Waste Book. Penerbit UTM , Johor, n/a. ISBN n/a Othman, Fadil and Ni'am, M. Faiqun (2008) Electrocoagulation for wastewater. In: Advances in Water and Wastewater Treatment Technologies. Penerbit UTM , Johor, p. 103. ISBN 978-983-52-0580-4 Othman, Mazlina Alang (2008) Deposition of sediment in detention pond - laboratory study. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. RRadin Sumadi, Salihuddin and Lee, Yee Loon (2008) Development of blended cements for water proofing application. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Submitted) Radin Sumadi, Salihuddin and Ramli, Mahyuddin (2008) Development of lightweight ferrocement sandwich panels for modular housing and industralized building system. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Ramali, Khairun Nadwah (2008) The impact of road construction on water quality at Kg. Sengkang, Mukim Gerisek, Muar. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Ramli, Mohd. Zamri and Adnan, Azlan (2008) Analysis of prestress concrete highway bridges with and without rubber bearing. In: Advances in Earthquake Engineering Application. Penerbit UTM , Johor, pp. 93-110. ISBN 978-983-52-0571-2 Ramli, Mohd. Zamri and Tay, Tzer Yong (2008) Buildings classification using applied technology council (ATC – 21). In: Advances in Earthquake Engineering Application. Penerbit UTM , Johor, pp. 49-60. ISBN 978-983-52-0571-2 Razman, Mohd. and Hadiwinot, Dewi Dwirianti and Ujang, Zaini (2008) Identification of sulphate reducing bacteria in membrane bioreactor treating high-sulphate wastewater. In: Advances in Water and Wastewater Treatment Technologies. Penerbit UTM , Johor, p. 146. ISBN 978-983-52-0580-4 Romali, Noor Suraya (2008) Evaluation and performance of gross pollutant traps (GPTs) for open channel flow. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. SSaad, Rosli and Mohd. Noordin, Mohd. Nawawi and Mohamad, Edy Tonnizam (2008) Subsidence prediction along the karak highway by 2-d electrical imaging geophysical method. Geotechnical & Highway Engineering . Saleh, Ahmed Moftah (2008) Comparison between the rolling thin film oven test and the pressure aging vessel aging simulation tests. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Saleh @ Aman, Shiadri (2008) Causes of poor participation of local workers in Malaysia construction industry and strategies for improvement. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Salim, Mohd. Razman and Ab. Wahid, Zularisam and Ismail, Ahmad Fauzi (2008) Effects of membrane cleaning techniques on NOM fouling and flux recovery. In: Advances in Water and Wastewater Treatment Technologies. Penerbit UTM , Johor, p. 42. ISBN 978-983-52-0580-4 Salim, Mohd. Razman and Ujang, Zaini and Anuar, Aznah Nor (2008) Development of laboratory scale Cyclic Activated Sludge Bioreactor (CASBio) to enhance aerobic sludge granulation (AGS) and Polyhydroxyalkanoates (PHA) recovery. Project Report. Faculty of Civil Engineering, Skudai, Johor. (Unpublished) Salim, Mohd. Razman and Ujang, Zaini and Salmiati, Salmiati (2008) Horizontal Subsurface Constructed Wetlands (HSFCW). In: Waste Book. Penerbit UTM , Johor. Salmiati, Salmiati (2008) Intracellular biopolymer production from fermented palm oil mill effluent using mixed microbial cultures. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil engineering. Sardi, Arshad (2008) The impact of the submerged geotube breakwater as a coastal protection at Tanjung Piai, Pontian, Johor. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Setiani, Yulia (2008) Construction site security management and control. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Shamsuddin, Shuhana and Ujang, Norsidah (2008) Making places: the role of attachment in creating the sense of place for traditional streets in Malaysia. Habitat International, 32 (3). 399 -409. ISSN 0197-3975 Shukor, Muhamad Fuad (2008) Low electric energy for colour removal of dye solution. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Suif, Zuliziana (2008) Risk based analysis for detention pond overflow at Iskandar Malaysia (Nusajaya), Johor. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Sumiri, Samsulkamal (2008) Public participation on sustainable development - investigation of the level of sustainable environmental development understanding and awareness. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Sunaryati, Jati (2008) Behaviour of steel structures with base isolator under low intensity earthquake effect. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Sutejo, Yulindasari and Asof, Marwan and Gofar, Nurly (2008) Prediction of settlement of road construction on peat. Geotechnical & Highway Engineering . TTan, Hean Seong (2008) Behaviour of cold formed steel under axial compression force. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Tee, Lian Yong (2008) Performance of concrete containing engine oil. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Teow, Ching Ching (2008) Seismic vulnerability study of guillemard railway bridge. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Thong, Jia Wen (2008) Reengineering of ISO 9001:2000 document management system compliance with construction inspection process. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Tiong, Hwa Nguong (2008) Short-term ageing effects on asphalt binders. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Tiong, Mee Ling (2008) Integration of chemical-biological oxidation processes in treating synthetic dyeing wastewater. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Trang Nhat, Tran (2008) The relationship of bitumen content, aggregate surface area, and extraction time using asphalt ignition furnace. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. UUsman, Fathoni (2008) Neural network model development for service life prediction of building components. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil engineering. Utomo, Handojo Djati and Hunter , Keith A. (2008) Adsorption of lead ions from aqueous solution by various. In: Waste Book. Penerbit UTM , Johor, n/a. ISBN n/a WWahi, Noraziah (2008) Minimising construction disputes. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Wan Hassan, Wan Najihah Farhanah (2008) The application of monte carlo simulation in structure reliability assessment (case study of offshore pipelines). Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Wiyono, Sugeng and Che Puan, Othman and Hainin, Mohd. Rosli (2008) Crack progression models for flexible pavements. In: Highway Materials and Construction. Penerbit UTM , Johor, pp. 63-71. ISBN 978-983-52-0574-3 Wong, Wai Seng (2008) Treatment of flocculation disturbance and algae - laden water for potable use. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering . YYaacob, Haryati and Hainin, Mohd. Rosli and Woodward, David and Woodside, Alan (2008) Changes of surface dressing texture as related to time and chipping size. Malaysian Journal of Civil Engineering, 20 (1). pp. 1-11. ISSN 1823-7843 Yahya, Khairulzan and Boussabaine, A. Halim (2008) Developing a framework for assessing eco-costs of construction site activities. In: The Walking Talk on Sustainable Development Issues Policies, Strategies And Techniques. Penerbit UTM , Johor, pp. 59-77. ISBN 978-983-52-0566-8 Yahya, Khairulzan and Boussabaine, A. Halim and Haron, Zaiton and Zakaria, Rozana (2008) Eco-costs of sustainable construction waste management in Malaysia. In: Issues in Construction Industry. Penerbit UTM , Johor, pp. 35-50. ISBN 978-983-52-0568-2 Yang, Eik Hien (2008) Effects of prefabricated vertical drain on the performance of embankment on soft ground. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Yero, Arafat Suleiman (2008) The determination of the texture depth, skidding resistance and roughness index of various bituminous road surfaces. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Yusop, Zulkifli and Chong, Meng Hui and Garusu, Geoffery James and Ayob, Katimon (2008) Estimation of evapotranspiration in oil palm catchments by short-time period water-budget method. Malaysian Journal of Civil Engineering, 20 (2). pp. 160-174. ISSN 1823-7843 ZZainal Abidin, Mohd. Kamarul Izwan (2008) The causes and impact of poor construction documentation in construction organizations. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Zainuddin, Ahmad Sayufei (2008) Maintenance consideration in slope design. Masters thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. Zaly, Mohammad and Che Puan, Othman (2008) Multivariate regression model between land uses and road density. Geotechnical & Highway Engineering . Zulfa Fauzia, Zulfa Fauzia (2008) The application of magnetic fields for landfill leachate treatment. PhD thesis, Universiti Teknologi Malaysia, Faculty of Civil Engineering. |