Browse by Faculty

Jamaludin, Khairur Rijal and Muhamad, Norhamidi (2010) Rheological investigation of water atomized metal injection molding (MIM) feedstock for processibility prediction. Advanced Materials Research, 83-86 (http://dx.doi.org/10.4028/www.scientific.net/AMR.83-86.945). pp. 945-952. ISSN 1022-6680

Saqr, Khalid M. and Musa, Md. Nor (2009) Critical review of thermoelectrics in modern power generation applications. Thermal Science, 13 (3). 165 -174. ISSN 0354-9836

Jamaludin, Khairur Rijal and Muhamad, Norhamidi (2009) An influence of a binder system to the rheological behavior of the SS16l metal injection molding (MIM) feedstock. In: The International Conference on Advances in Materials and Processing Technologies, 26-28 October 2009, Kuala Lumpur, Malaysia.

Jamaludin, Khairur Rijal and Norhamidi, Norhamidi and Ab. Rahman, Mohd Nizam (2009) Orthogonal array technique for optimizing the sintering parameter of the metal injection molding (MIM) compact: best flexure strength. In: The International Conference on Advances in Materials and Processing Technologies, 26-28 Oktober 2009, Kuala Lumpur, Malaysia.

Ibrahim, Mohd Halim Irwan and Muhamad, N. and Jamaludin, Khairur Rijal (2009) Rheological characterization of water atomised stainless steel powder for micro metal injection molding. In: The International Conference on Advances in Materials and Processing Technologies, 26-28 October 2009, Kuala Lumpur, Malaysia.

Mohamad Nor, N. H. and Muhamad, Norhamidi and Jamaludin, Khairur Rijal and Ahmad, Sufizar (2009) Characterisation of titanium alloy feedstock for metal injection moulding using palm stearin binder system. In: The International Conference on Advances in Materials and Processing Technologies, 26-28 October 2009, Kuala Lumpur, Malaysia.

Jamaludin, Khairur Rijal and Ahmad, Sufizar (2009) Taguchi method for the determination of optimised sintering parameters of titanium alloy foams. In: The International Conference on Advances in Materials and Processing Technologies, 26-28 October 2009, Kuala Lumpur, Malaysia.

Jamaludin, Khairur Rijal (2009) Sintering parameter optimization with quality engineering technique : best flexure strength. In: 3rd Powder Metallurgy Symposium & Exhibition 2009, 12-13 August 2009, Kuala Lumpur, Malaysia. (Unpublished)

Jamaludin, Khairur Rijal and N., Muhamad (2009) Taguchi Method for Optimising the Sintering Parameter of the Metal Injection Moulding (MIM) Compacts. In: International Conference on Flexible Automation and Intelligent Manufacturing, 6-8 July 2009, University of Teeside, Middlesbrough, United Kingdom.

Harun, Mohd Ruzi and Muhamad, Norhamidi and Jamaludin, Khairur Rijal (2009) A review of workability of wrought magnesium alloys. In: Advanced Manufacturing Research Group Seminar, July 2009, Kajang, Selangor.

Jamaludin, Khairur Rijal and Mohamad Nor, Nor Hafiez (2009) Feedstock characterisation of titanium alloy mix with palm stearin binder system for metal injection moulding. In: Advanced Manufacturing Research Group Seminar, 2009, Kajang, Selangor.

Salim, M. A. and Md. Zain, M. Z. and Abu-Bakar, A. R. and Noordin, A. (2009) Simulation of an input shaping scheme technique to investigate unwanted noise and vibration in wiper blade. Journal of Mechanical Engineering and Technology, 1 (1). pp. 1-13. ISSN 2180-1053

Ali, Mohamed Assnousi (2009) Corrosion behaviour of ductile cast iron. Masters thesis, Universiti Teknologi Malaysia.

Koloor Saeid Rahimian, Seyed (2009) Damage mechanics of composite laminates subjected to cyclic flexual load. Masters thesis, Universiti Teknologi Malaysia.

Annamalai Gurunathan, Balamurugan (2009) Energy absorption of impact damper. Masters thesis, Universiti Teknologi Malaysia.

Poobalan, Prakash (2009) Equipment and process performance improvement using automated monitoring system. Masters thesis, Universiti Teknologi Malaysia.

Baharudin, Bakhtiar Ariff (2009) Further validations of the hydrodynamic force coefficients for a laterally drifting ship in waves. Masters thesis, Universiti Teknologi Malaysia.

Che Wan Othman, Che Wan Mohd. Noor (2009) Manoeuvring prediction of offshore supply vessel. Masters thesis, Universiti Teknologi Malaysia.

Chew, Li Ling (2009) Process improvement using six sigma methodology. Masters thesis, Universiti Teknologi Malaysia.

Sharmugham, Thinesh Kumar (2009) Refined numerical simulation of the mechanical behaviour of hollow sphere structures. Masters thesis, Universiti Teknologi Malaysia.

Priyandoko, Gigih and Mailah, Musa and Jamaluddin, H (2009) Vehicle active suspension system using skyhook adaptive neuro active force control. Mechanical System and Signal Proceessing, 23 (3). pp. 855-868. (In Press)

Ahmad, S. and Muchtar, A. and Muhamad, N. and Sahari, J. and Jamaludin, K. R. and Ibrahim, M. H. I. (2009) Optimising of processing parameters of Titanium alloy foams using Taguchi method for improved electrical conductivity. In: Proceedings of the Graduate Publication Workshop 2009, 30-31 Mac 2009, The Residence Hotel, UNITEN.

Jamaludin, K. R. and Muhamad, Norhamidi and Ab. Rahman, M. N. and Amin, S. Y. M. and Ahmad, S. and Ibrahim, M. H. I. (2009) Sintering parameter optimisation of the SS316L metal injection molding (MIM) compacts for final density using Taguchi method. In: The 3rd South East Asian Technical University Consortium (SEATUC) Symposium, 25 - 26 Feb 2009 , Johor Bahru, Johor, Malaysia.

Abd. Wahid, Mazlan (2009) Biofuel Pulse Combustion Characteristics. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Wong, Kuan Yew and See, Phen Chiak (2009) A new minimum pheromone threshold strategy (MPTS) for max–min ant system. Applied Soft Computing, 9 (3). pp. 882-888. ISSN 1568-4946

Izman, S. and Tamin, Mohd. Nasir and Venkatesh, V. C. and Mon, T. T. (2009) Evaluation of a material flow stress model adopted in finite element modeling of metal cutting. International Journal for Manufacturing Science and Technolog, 9 (2). pp. 67-73. ISSN 1524-1548

Chong, C.W. and Chong, S.C. and Wong, Kuan Yew (2009) Is the Malaysian telecommunication industry ready for knowledge management implementation? Journal of Knowledge Management, 13 (1). pp. 69-87. ISSN 1367-3270

Jamaludin, Khairur Rijal (2009) Kesan saiz dan bentuk partikel serbuk SS316l terhadap parameter pengacuanan suntikan logam menggunakan rekabentuk eksperimen. PhD thesis, Universiti Kebangsaan Malaysia.

Jamaludin, Khairur Rijal and Muhamad, Norhamidi and Ab. Rahman, Mohd Nizam and M. Amin, Sri Yulis and Ahmad, Sufizar and Ibrahim, Mohd Halim Irwan and Murtadhahadi, I and Mohamad Nor, Nor Hafiez (2008) Densification of SS316L Gas-Atomized and Water-Atomized Powder Compact. In: of Seminar 2ndAMREG 08, 17 Nov 2008, Port Dickson, Malaysia, 17 & 18 December 2008, Port Dickson, Negeri Sembilan, Malaysia.

Ibrahim , M.H.I and Muhamad, N. and Sulong, A.B. and Murtadhahadi, I and Jamaludin, K.R. and Ahmad, S. and Nor, N.H.M (2008) Rheological Characteristic of Water Atomised Stainless Steel Powder for Micro Metal Injection Molding. In: Second Advanced Manufacturing Researach Group Seminar , 17 & 18 December 2008, Port Dickson, Negeri Sembilan.

Muhamad, Norhamidi and Murtadhahadi, I. and Sulong, Abu Bakar and Che Harun, Che Hassan and Jamaludin, Khairur Rijal and Ibrahim, Mohd Halim Irwan (2008) Kesan Parameter Percampuran Dan Pembutiran Ke Atas Penyediaan Bahan Suapan Yang Optimum Bagi Proses Pengacuan Suntikan Logam. In: Malaysian Metalurgical Conference 2008, 3 & 4 December 2008, Bangi, Selangor.

Ibrahim , M.H.I and Muhamad, N. and Sulong, A.B. and Murtadhahadi, I and Jamaludin, K.R. and Ahmad, S. and Nor, N.H.M (2008) Water Atomised Stainless Steel Powder for Micro Metal Injection Molding: Optimization of Rheological Properties. In: Malaysian Mettallurgical Conference 2008, 3-4 December 2008, Bangi, Selangor.

Islam, M. Rafiqul and Ibn Awal, Zobair (2008) A study on ship capsizing due to collision. Jurnal Mekanikal (26). pp. 22-36. ISSN 0127-3396

Md. Zain, M. Z. and Mailah, Musa and Priyandoko, G. (2008) Active force control with input shaping technique for a suspension system. Jurnal Mekanikal (27). pp. 91-104. ISSN 0127-3396

Lazim, Azrina (2008) An optimization of tin plating process using design of experiment. Masters thesis, Universiti Teknologi Malaysia.

Abd. Karim, Mohd. Fauzi (2008) Corrosion behavior of deformed steel for automobile parts in various environments. Masters thesis, Universiti Teknologi Malaysia.

Baharin, Nor Hatini (2008) Effect of accelerometer mass on thin plate vibration. Masters thesis, Universiti Teknologi Malaysia.

Tan, Ming Jiun (2008) Effect of alumina-formers addition on the isothermal oxidation of TI-AL based intermetallics. Masters thesis, Universiti Teknologi Malaysia.

Eldrainy, Yehia A. and Mohd. Jaafar, Mohammad Nazri and Mat Lazim, Tholudin (2008) Numerical investigation of the flow inside primary zone of tubular combustor model. Jurnal Mekanikal (26). pp. 162-176. ISSN 0127-3396

Sawarimuthu, Soosai and Mohd. Jaafar, Mohammad Nazri (2008) Performance of various biofuel blends on burner system. Jurnal Mekanikal (27). pp. 69-77. ISSN 0127-3396

Ibrahim, Ahmad Azlan Shah and Mohd. Jaafar, Mohammad Nazri (2008) Power estimation for four seater helicopter. Jurnal Mekanikal (27). pp. 78-90. ISSN 0127-3396

Abdul Ghani, Mohamad Pauzi and Julait, J. (2008) Prediction of added resistance of ship due to regular head waves. Jurnal Mekanikal (26). pp. 1-8. ISSN 0127-3396

Ho, Fu Haw (2008) Production scheduling system for job shop enterprise using ANT colony optimization approach. Masters thesis, Universiti Teknologi Malaysia.

Mohd. Samin, Pakharuddin and Jamaluddin, Hishamuddin and Abd. Rahman, Roslan and Abu Bakar, Saiful Anuar and Hudha, Khisbullah (2008) Semi-active suspension for ride improvement using stability augmentation system control algorithm. Jurnal Mekanikal (26). pp. 86-95. ISSN 0127-3396

Che Sidik, Nor Azwadi and Rosdzimin, A. R. M. (2008) Simulation of natural convention heat transfer in an enclosure using lattice boltzmann method. Jurnal Mekanikal (27). pp. 42-50. ISSN 0127-3396

Abd. Rahman, Roslan and Tamin, Mohd. Nasir and Kurdi, Ojo (2008) Stress analysis of heavy duty truck chasis as a preliminary data for its fatigue life prediction using FEM. Jurnal Mekanikal (26). pp. 76-85. ISSN 0127-3396

Priyanto, Agoes and Erwandi, Erwandi and Samudro, Samudro (2008) Surge forces of a FPSO at lee side of submerged plate in regular waves. Jurnal Mekanikal (26). pp. 63-75. ISSN 0127-3396

Mat Saman, Muhamad Zameri and Blount, Gordon (2008) The DFEL value methodology: a tool for design-for-environment in automotive industry. Jurnal Mekanikal (27). pp. 23-41. ISSN 0127-3396

Afrinaldi, Feri and Mat Saman, Muhamad Zameri and Shaharoun, A. M. (2008) The evaluation methods of disassemblability for automotive components – review and agenda for future research. Jurnal Mekanikal (26). pp. 49-62. ISSN 0127-3396

Ishak, Mohmad Shaiful Ashrul and Mohd. Jaafar, Mohammad Nazri (2008) The influence of orifice insertionin radial swirling flow for low emissions combustion. Jurnal Mekanikal (26). pp. 96-106. ISSN 0127-3396

Abdul Latiff, Zulkarnain and Abdul Aziz, Azhar and Suptiyano, Bambang and Said, Mazlan (2008) Viability study of ethylene (C2H4) as an alternative fuel for gasoline engine. Jurnal Mekanikal (26). pp. 151-161. ISSN 0127-3396

Jamaludin, K. R. and Muhamad, N. and Ab. Rahman, M. N. and Amin, S. Y. M. and Ahmad, S. and Ibrahim, M. H. I. and Murtadhahadi, I. and Nor, N. H. M. (2008) An Influence of SS316L’s Particle Shape to the Injection Molding of Composite Binder Feedstock. In: Confederation of ASEAN Engineers Organization Conference 2008 , 26-29 November 2008, Bangkok, Thailand.

M. Amin, Sri Yulis and Muhamad, Norhamidi and Abdullah, Shahrir and Jamaludin, Khairur Rijal (2008) Application of RSM Technique to Optimize the Solvent Debinding Process for MIM Compacts. In: Brunei International Conference of Engineering & Technology (BICET) 2008, 3 and 4th November 2008, Brunei Darulsallam.

Ahmad, S. and Muhamad, N. and Muchtar, A. and Sahari, J. and Jamaludin, Khairur Rijal and Ibrahim, M. H. I. and Mohamad Nor, N. H. and Murtadhahadi, I. (2008) Producing of titanium foam using titanium alloy (Al3Ti) by slurry method. In: Brunei International Conference of Engineering and Technology (BICET) 2008, 3 and 4th November 2008, Brunei Darulssalam.

Jamaludin, Khairur Rijal and Muhamad, N. and Ab. Rahman, M. N. and Murtadhahadi, I and Amin, S. Y. M. and Ahmad, S. and Ibrahim, M. H. I. and Nor, N. H. M. (2008) Rheological investigation of water atomised Metal Injection Molding (MIM) feedstock for processbility prediction. In: Advances in Materials and Processing Technologies (AMPT) conference 2008, 2-5 November 2008, Manama, Kingdom of Bahrain.

Yahya, M. Yazid and Cantwell, W. J. and Langdon, G. S. and Nurick, G. N. (2008) The blast behaviour of fiber reinforced thermoplastic laminates. Journal of Composite Materials, 42 (21). pp. 2275-2297. ISSN 1530-793X

Alias, Juliawati (2008) Biotribocorrosion performance of titanium alloy Ti-6AI-4V and stainless steel 316l under simulated body environment. Masters thesis, Universiti Teknologi Malaysia.

Rashiddy Wong, Freddawati (2008) Effect of drill geometry of uncoated tool when drilling titanium alloy, Ti-6Al-4V. Masters thesis, Universiti Teknologi Malaysia.

Ramlee, Norlaila (2008) Effect of pH, temperature and chloride concentrations on the corrosion behaviour of welded 316L stainless steel. Masters thesis, Universiti Teknologi Malaysia.

Ali, Md. Liakat (2008) Impact on bus superstructure due to rollover. Masters thesis, Universiti Teknologi Malaysia.

Oshaghi, Safoura (2008) Study of interfacial reactions between lead-free solders and immersion silver finish. Masters thesis, Universiti Teknologi Malaysia.

Mohammed, Akmal Nizam (2008) Swirl flow in combustion chambers. Masters thesis, Universiti Teknologi Malaysia.

Mahat, Mohamad Mazwan (2008) The effect of stents structural parameters to flow in stented aneurysms. Masters thesis, Universiti Teknologi Malaysia.

Ahmad, Robiah and Jamaluddin, Hishamuddin and Hussain, Mohd. Azlan (2008) Application of memetic algorithm in modelling discrete-time multivariable dynamics systems. Mechanical Systems and Signal Processing, 22 (7). pp. 1595-1609. ISSN 0888-3270

Ahmad, Robiah and Jamaluddin, Hishamuddin and Hussain, Mohd. Azlan (2008) Application of memetic algorithm in modelling discrete-time multivariable dynamics systems. Mechanical Systems and Signal Processing, 22 (7). pp. 1595-1609. ISSN 0888-3270

Ali, M. and Hamzah, E. and Abbas, T. and Mohd Toff, M.R.H. and Qazi, I.A. (2008) Macrodroplet reduction and growth mechanisms in cathodic arc physical vapor deposition of TiN films. Surface Review and Letters , 15 (5). pp. 653-659. ISSN 0218625X

Rajoo, Srithar and Botas, Ricardo Martinez (2008) Variable geometry mixed flow turbine for turbochargers: an experimental study. International Journal of Fluid Machinery and Systems, 1 (1). pp. 155-168. ISSN 1882-9554 online

Che Sidik, Nor Azwadi and Takahiko, Tanahashi (2008) Simplified Finite Difference Thermal Lattice Boltzman Method. International Journal of Modern Physics B, 22 . 3865 -3876. ISSN 0217-9792

Abu Bakar, Abd Rahim and Ouyang, Huajiang (2008) Recent studies of car disc brake squeal. In: New Research on Acoustics. Nova Science Publishers, Inc, New York, pp. 159-196. ISBN 978-1-60456-403-7

Zakuan, N.M. and Yusof, S.M. and Laosirihongthong, T. (2008) Reflective review of relationship between Total Quality Management and organizational performance. In: Proceedings of the 4th IEEE International Conference on Management of Innovation and Technology, ICMIT, 21-24 Sept. 2008 , Bangkok, Thailand.

Saqr, Khalid M. and ElDrainy, Yehia A. and Musa, Md. Nor (2008) 3-D numerical study of the effect of fin discontinuity on heat transfer augmentation in pipes having internal longitudinal fins for turbulent compressible flow. Proceedings of the 1st International Meeting on Advances in Thermofluids . pp. 195-206. ISSN ISBN 978-983-9805-62-8

Saqr, Khalid M. and Musa, Md. Nor (2008) On the deployment of thermoelectric waste heat recovery in the Malaysian road transport sector. Proceedings of the 1st International Meeting on Advances in Thermofluids . pp. 234-241.

Mubarak, A. and Akhter, Parvez and Hamzah, Esah and Mohd Toff, Mohd Radzi and A.Qazi, Ishtiaq (2008) Effect of Coating Thickness on the Properties of TiN Coatings Deposited on Tool Steels using Cathodic ARC PVD Techique. Surface Review and Letters, 15 (4). pp. 401-410. ISSN 0218-625X

Mubarak, Ali and Akhter , Parvez and Hamzah, Esah and Mohd Toff, Mohd Radzi and A. Qazi, Ishtiaq (2008) Effect of coating thickness on the properties of TiN coatings deposited on tool steels using cathodic arc PVD technique. Surface Review and Letters, 15 (4). pp. 401-410. ISSN 0218-625X

Rajoo, Srithar and Martinez-Botas, Ricardo (2008) Mixed flow turbine research: A review. Journal of Turbomachinery, 130 (4). 044001-044012. ISSN 0889-504X

Basaran, C. and S., Li and Abdul Hamid, M. F. (2008) Thermomigration induced degradation in solder alloys. American Institute of Physics, 103 (12). pp. 1-9. ISSN 1070-664X

Jamaludin, Khairur Rijal and Muhamad, Norhamidi and Ab. Rahman, Mohd Nizam and M. Amin, Sri Yulis and Ahmad, Sufizar and Ibrahim, Mohd Halim Irwan and Ibrahim, Murtadhahadi and Mohamad Nor, Nor Hafiez (2008) Analisis taburan saiz partikel serbuk SS316L bagi kegunaan proses penyuntikan acuan logam. In: Seminar I - AMReG 08, 12th June 2008, Seremban, Malaysia.

M. Amin, Sri Yulis and Muhamad, Norhamidi and Abdullah, Shahrir and Jamaludin, Khairur Rijal (2008) Kajian pengoptimuman penyahikatan larutan menggunakan kaedah permukaan sambutan. In: Seminar I - AMReG 08, 12 Jun 2008, Seremban, Malaysia.

Jamaludin, Khairur Rijal and Muhamad, Norhamidi and Ab. Rahman, Mohd Nizam and M. Amin, Sri Yulis and Ahmad, Sufizar and Ibrahim, Mohd Halim Irwan and Ibrahim, Murtadhahadi and Mohamad Nor, Nor Hafiez (2008) Kajian prestasi penyahikatan larutan dengan menggunakan kaedah taguchi. In: Seminar I - AMReG 08, 12 Jun 2008, Seremban, Malaysia.

Muhamad, Norhamidi and Ibrahim, Murtadhahadi and Che Haron, Che Hassan and Sulong, Abu Bakar and Jamaludin, Khairur Rijal and Ahmad, Sufizar and Ibrahim, Mohd Halim Irwan and Mohamad Nor, Nor Hafiez (2008) Kesan suhu penyuntikan yang tidak optimum terhadap kecacatan jasad anum pada proses penyuntikan logam (MIM). In: Seminar AMREG 08, 12 Jun 2008, Seremban, Malaysia.

Ahmad, Sufizar and Muhamad, Norhamidi and Muchtar, Andanastuti and Sahari, Jaafar and Jamaludin, Khairur Rijal and Ibrahim, Mohd Halim Irwan and Mohamad Nor, Nor Hafiez and Ibrahim, Murtadhahadi (2008) Pembangunan dan penghasilan titanium berbusa. In: Seminar I - AMReG 08, 12 Jun 2008, Seremban, Malaysia.

Muhamad, Norhamidi and Ibrahim, Murtadhahadi and Che Harun, Che Hassan and Sulong, Abu Bakar and Jamaludin, Khairur Rijal and Ahmad, Sufizar and Ibrahim, Mohd Halim Irwan and Mohamad Nor, Nor Hafiez (2008) Pembebanan serbuk yang optimum bagi bahan suapan daripada SS 316 L, PEG, PMMA dan AS bagi proses pengacuanan suntikan logam (MIM). In: Seminar I - AMReG 08, 12 June 2008, Seremban, Malaysia.

Mohamad Nor, Nor Hafiez and Muhamad, Norhamidi and M. Amin, Sri Yulis and Ahmad, Sufizar and Ibrahim, Mohd Halim Irwan and Ibrahim, Murtadhahadi and Jamaludin, Khairur Rijal (2008) Pengacuan suntikan logam (MIM) bagi serbuk titanium dengan sistem bahan pengikat stearin sawit. In: Seminar I - AMReG 08, 12 Jun 2008, Seremban, Malaysia.

Jamaludin, Khairur Rijal and Muhamad, Norhamidi and Ab. Rahman, Mohd Nizam and M. Amin, Sri Yulis and Ahmad, Sufizar and Ibrahim, Mohd Halim Irwan and Ibrahim, Murtadhahadi and Mohamad Nor, Nor Hafiez (2008) Pengaruh tekanan penyuntikan, suhu penyuntikan dan beban serbuk terhadap ketumpatan jasad anum: analisis varian. In: Seminar I - AMReG 08, 12 June 2008, Seremban, Malaysia.

Ibrahim, Mohd Halim Irwan and Muhamad, Norhamidi and Jamaludin, Khairur Rijal and Ahmad, Sufizar and Mohamed Nor, Norhafiez and Ibrahim, Murtadhahadi (2008) Pengoptimuman parameter dalam pengacuan suntikan logam mikro (µMIM). In: Seminar AMREG 08, 12 Jun 2008, Seremban, Malaysia.

Jamaludin, K. R. and Muhamad, N. and Ab. Rahman, M. and Amin, S. Y. M. and Murtadhahadi, - and Ismail, M. H. (2008) Injection molding parameter optimization using the taguchi method for highest green strength for bimodal powder mixture with SS316L in PEG and PMMA. In: World Congress on Powder Metallurgy & Particulate Materials, 8-12 June 2008, Washington D. C..

Abu Bakar, A. R. and Ouyang, Huajiang (2008) Wear prediction of friction material and brake squeal using the finite element method. Wear, 264 (11-12). pp. 1069-1076. ISSN 0043-1648

Hamzah, Esah and Sudin, Izman and Khoo, C. Y. (2008) A review on the rotary ultrasonic machining of advanced ceramics. Jurnal Mekanikal (25). pp. 9-23. ISSN 0127-3396

Mailah, Musa and Lim, Boon Han (2008) Biometric signature verification using pen position, time, velocity and pressure parameters. Jurnal Teknologi, 48 (A). pp. 35-54. ISSN 0127-9696

Mailah, Musa and Lim, Boon Han (2008) Biometric signature verification using pen position, time, velocity and pressure parameters. Jurnal Teknologi, A (48). pp. 35-54. ISSN 0127-9696

M., Khamis Mansour, and Musa, M. N. and Wan Hassan, M. N. (2008) Development of novel control strategy for multiple circuit, roof top bus air conditioning system in hot humid countries. Energy Conversion and Management, 49 . pp. 1455-1468. ISSN 0196-8904

Cha Sidik, Nor Azwadi and Osman, Kahar and Khudzairi, Ahmad Zahran and Ngali, Zamani (2008) Numerical investigation of lid-driven cavity flow based ontwo different methods: lattice boltzmann and splitting method. Jurnal Mekanikal (25). pp. 1-8. ISSN 0127-3396

Yeo, Eng Soon and Mohd. Ghazali, Normah (2008) Numerical simulation of a microchip cooling wth microjet array. Jurnal Mekanikal (25). pp. 39-49. ISSN 0127-3396

Muhamad , Norhamidi and Jamaludin, Khairur Rijal and M. Amin, Sri Yulis and Ab. Rahman, Mohd. Nizam (2008) Pemilihan bahan suapan bagi proses pengacuan suntikan logam berdasarkan kepada kajian sifat reologi. Jurnal Teknologi Siri A, 48(A) ( ). pp. 19-34. ISSN 0127-9696

Jamaludin, Khairur Rijal and Muhamad, Norhamidi and M. Amin, Sri Yulis and Ab. Rahman, Mohd Nizam and Ibrahim, Murtadhahadi (2008) Pengoptimuman parameter pengacuan bagi mengurangkan kecacatan jasad anum proses pengacuan suntikan logam (MIM). Journal - The Institution of Engineers, Malaysia, 69 (2). pp. 40-46. ISSN 0126-513X

Eldrainy, Yehia A. and Muhamad Ridzwan, Johann Jeffrie and Mohd. Jaafar, Mohammad Nazri (2008) Prediction of the flow inside a micro gas turbine combustor. Jurnal Mekanikal (25). pp. 50-63. ISSN 0127-3396

Jamaludin, Khairur Rijal and Muhamad, Norhamidi and Ab. Rahman, Mohd Nizam and M. Amin, Sri Yulis and Hadi, Murtadhahadi (2008) Analysis of variance on the metal injection molding parameters using a bimodal particle size distribution feedstock. In: International Conference on Mechanical & Manufacturing Engineering (ICME2008), 21– 23 May 2008, Johor Bahru.

Abdul Raman, Norazmein and Jamaludin, Khairur Rijal (2008) Implementation of Toyota Production System (TPS) in the production line of a local automotive parts manufacturer. In: International Conference on Mechanical & Manufacturing Engineering (ICME2008), 21– 23 May 2008, Johor Bahru.

Abdul Talib, Hayati @ Habibah and Mohd Ali, Khairul Anuar and Jamaludin, Khairur Rijal (2008) Quality assurance in halal food manufacturing in Malaysia: a preliminary study. In: International Conference on Mechanical & Manufacturing Engineering (ICME2008), 21– 23 May 2008, Johor Bahru.

Habeed Mohd. Abd Settar, Nurudin (2008) Thermal performance of a thermoacoustic stack. Masters thesis, Universiti Teknologi Malaysia.

Jamaludin, Khairur Rijal and Muhamad, Norhamidi and Ab. Rahman, Mohd Nizam and M. Amin, Sri Yulis and Ismail, Muhammad Hussain and Ibrahim, Murtadhahadi (2008) Particle size and injection temperature effect on the injection molding of SS316l powder. Journal of Mechanical Engineering , 5 (1). pp. 59-71. ISSN 1823-5514

Saqr, Khalid M. and Mansour, M. Khamis and Musa, Md. Nor (2008) Thermal design of automobile exhaust based thermoelectric generators : objectives and challenges. International journal of automotive technology, 9 (2). pp. 155-160. ISSN 1229-9138

Saqr, K. M. and Mansour, M. K. and Musa, M. N. (2008) Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges. International journal of automotive technology, 9 (2). pp. 155-160. ISSN 1229-9138

Ramli, Nabilah (2008) Identification of ground vehicle’s aerodynamic derivatives using neural network. Masters thesis, Universiti Teknologi Malaysia .

S. , Kamitani and K. , Nakanisi and S., Syahrullail (2008) Improvement of surface roughness of aluminum products by the micro-grooves on tool surface in cold extrusion. Keikinzoku/Journal of Japan Institute of Light Metals, 58 . pp. 111-116. ISSN 0451-5994

Mansour, M. Khamis and Musa, Md. Nor and Wan Hassan, Mat Nawi and Saqr, Khalid M. (2008) Development of novel control strategy for multiple circuit, roof top bus air conditioning system in hot humid countries. Energy conversion and management, 49 (6). pp. 1455-1468. ISSN 0196-8904 (In Press)

Mubarak, A. and Hamzah, E. and M.R.M., Toff (2008) Study of Macrodroplet and Growth Mechanisms with and without Ion Etchings on the Properties of TiN Coatings Deposited on HSS using Cathodic Arc Physical Vapour Deposition Technique. Materials Science and Engineering: A, 474 (1-2). pp. 236-242. ISSN 09215093

Vesenjak, M. and Ren, Z. and Ochsner, Andreas (2008) Behaviour of cellular materials under impact loading. Materials Science and Engineering Technology, 39 (2). pp. 125-132. ISSN 0933-5137

Oliveira, B. F. and Cunda, L. A. B. and Ochsner, Andreas and Creus, G. J. (2008) Comparison between RVE and full mesh approaches for the simulation of compression tests on cellular metals. Materials Science and Engineering Technology, 39 (2). pp. 133-142. ISSN 0933-5137

Fiedler, T. and Ochsner, Andreas (2008) Experimental analysis of the flexural properties of sandwich panels with cellular core materials. Materials Science and Engineering Technology, 39 (2). pp. 121-124. ISSN 0933-5137

Abdul Wahid, Mazlan and Ujir, Mohd Hafis and B, Azwan (2008) Effect of inlet section on pulse combustor performance. Jurnal Teknos-2K, 8 (1). pp. 9-14. ISSN 1411-4151

Saqr, Khalid M. and Musa, Md. Nor (2008) Simulation of a novel hot-side heat exchanger for automobile exhaust based thermoelectric generators using EFDlab. Jurnal Teknos-2K, 8 (1). pp. 17-26. ISSN 1411-4151

Wong, Kuan Yew and Okfalisa, Okfalisa and Salim, Naomie (2008) A knowledge diagnostic system for product defects. International Conference on Innovative Production Machines and Systems . pp. 244-249.

Ochsner, Andreas and Mishuris, Gennady (2008) A new finite element formulation for thin non-homogenous heat-conducting adhesive layers. Journal of Adhesion Science and Technology, 22 (13). pp. 1365-1378. ISSN 0169-4243

Abu Bakar, A. R. and Ouyang, H. (2008) A Prediction Methodology of Disk Brake Squeal using Complex Eigenvalue Analysis. Int. J. Vehicle Design, 46 (4). pp. 416-435. ISSN 0143-3369

Abu Bakar, Abd Rahim and Ouyang , Huajiang (2008) A prediction methodology of disk brake squeal using complex eigenvalue analysis. International Journal of Vehicle Design 2008, 46 (4). pp. 416-435.

Nilda Tri, Putri and Yusof, Sha'ri Mohd (2008) A review of quality engineering tools and techniques practices in Malaysia's and Indonesia's automotive industries and an agenda for future research. In: Proceedings of the 4th IEEE International Conference on Management of Innovation and Technology, ICMIT , 21-24 Sept. 2008.

Wong, Wai Peng and Wong, Kuan Yew (2008) A review on benchmarking of supply chain performance measures. Benchmarking, 15 (1). pp. 25-51. ISSN 1463-5771

Ibn Awal, Zobair and Islam, M. Rafiqul (2008) A study on ship capsizing due to collision. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Perumal, Kannan and Mansor, Shuhaimi (2008) A synthesis of aircraft approach, landing and overrun. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Mansor, Shuhaimi and Perumal, Kannan (2008) A synthesis of an aircraft approach, landing & overrun. Jurnal Mekanikal (26). pp. 141-150. ISSN 0127-3396

Wong, Kuan Yew (2008) An exploratory study on knowledge management adoption in the Malaysian industry. International Journal of Business Information Systems , 3 (3). pp. 272-283. ISSN 1746-0972

Wong, Kuan Yew and Komarudin, - (2008) Ant Colony Optimization in Solving Facility Layout Problems. In: International Conference on Mechanical & Manufacturing Engineering (ICME 2008), 21– 23 May 2008, Johor Bahru.

Phen, Chiak See and Wong, Kuan Yew (2008) Application of ant colony optimisation algorithms in solving facility layout problems formulated as quadratic assignment problems: a review. International Journal of Industrial and Systems Engineering , 3 (6). pp. 644-672. ISSN 1748-5037

Olugu, Ezutah Udoncy and Wong, Kuan Yew (2008) Application of Discrete Event Simulation of Process Flow in Small and Medium Scale Manufacturing Industries. In: International Conference on Mechanical & Manufacturing Engineering (ICME 2008), 21– 23 May 2008, Johor Bahru.

Nusyirwan, Istas Fahrurrazi (2008) Applying evolutionary programming to evade a missile. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15-16 July 2008, Hotel Istana, Kuala Lumpur.

Abdul Kadir, Mohammed Rafiq and Taib, I. and Osman , K. and Abdul Hamid, M. H. (2008) Blood Flow Simulation of Stented Aneurysm Model. In: IFMBE Proceedings. Springer Berlin Heidelberg, pp. 398-402. ISBN 1680-0737

Wan Ali, Wan Khairuddin and Mohd. Jaafar, Mohammad Nazri and Abdul-Latif, Ainullotfi and Dahalan, Md. Nizam and Abd Rahman, Abd Basid and Mat Yajid, Zuriana Mariati and Kimsin, Intan Noryanah (2008) Developing indigenous rocket motor: A UTM experience. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Kimsin, Intan Noryanah and Mohd. Jaafar, Mohammad Nazri and Wan Ali, Wan Khairuddin (2008) Development of a burning rate test rig for solid propellant performance investigation. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Ahmad, Nurulnatisya (2008) Development of fast craft seakeeping design methodology. Masters thesis, Universiti Teknologi Malaysia.

As'arry, A and Zain, M.Z Md and Hussien, M and Mailah, Musa and Abdullah, M.Y and Ahmad, R.R and Kazi, S (2008) Development of hand-arm model rig for tremor excitation. In: Proceedings - International Symposium on Information Technology 2008, ITSim .

Abu Bakar, A. R. (2008) Disc Brake Squeal: A Prediction Methodology. Technical Report. Vdm Verlag Dr. Muller.

Ab Kader, Ab. Saman and Oladokun, Sulaiman Olanrewaju and Ahmad, Mohd Zamani (2008) Environmental risk and compliance for nature gas ship design and operation within inland waterways. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Israr Ahmad, Haris Ahmad and Dahalan, Md. Nizam (2008) Estimation of lift and drag characteristics of UTM elang-1 UAV. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Abu Bakar, A. R. and Ouyang, H. and James, S and Li, L (2008) Finite Element Analysis of Wear and its Effect on Squeal Generation. Proc. IMechE Part D: J. Automobile Engineering, 222 (7). pp. 1153-1165. ISSN 0954-4070

Abdul-Kadir, Mohammed Rafiq and Ulrich, Hansen and Ralf, Klabunde and Duncan, Lucas and Andrew, Amis (2008) Finite element modelling of primary hip stem stability: The effect of interference fit. Journal of Biomechanics, 41 (Issue 3). 587-594 . ISSN 0021-9290

Abdul Kadir, Mohammed Rafiq and Kamsah, N. and Aminullah, M. A. (2008) Finite Element Study of Metacarpophalangeal Joint Silicone Implants. In: IFMBE Proceedings. Springer Berlin Heidelberg, pp. 420-423. ISBN 1680-0737

Ali, Mubarak and Hamzah, Esah and Toff, Mohammad Radzi (2008) Friction coefficient and surface roughness of TiN-coated HSS deposited using cathodic arc evaporation PVD technique. Industrial Lubrication and Tribology, 60 . pp. 121-130. ISSN 0036-8792

Hussain, A. and Ani, F. N. and Darus, A. N. (2008) Gas-solid flow modelling in a circulating fluidized bed. International Journal of Modelling and Simulation .

Abdul Wahid, Mazlan and Ujir, Mohd Hafis and M.S, Mohsin (2008) Impulse Measurement of Pulse Combustion Tube using Accelerometer. In: 9th Asia-Pacific International Symposium on Combustion and Energy Utilization, November 2008, Beijing, China.

Jamaludina, K. R. and Muhamad, N. and Ab. Rahman, M. N. and Amin, S. Y. M. and Murtadhahadi, I and Ismail, M. H. (2008) Injection molding parameter optimization using the Taguchi method for highest green strength for bimodal powder mixture with SS316L in PEG and PMMA. Advances in Powder Metallurgy & Particulate Materials 2008, 1 . pp. 186-194.

Abdul Kadir, Mohammed Rafiq and Syahrom, A. and Yusof, M. A. R. and Kamsah, N. (2008) Micro-modelling and Analysis of Actual and Idealised Cancellous Structure. In: IFMBE Proceedings. Springer Berlin Heidelberg, pp. 433-437. ISBN 1680-0737

Abdul Kadir, Mohammed Rafiq and Haron, H. and Kamsah, N. and Nordin, N. (2008) Miniplates Orientation for Fracture Fixation of the Mandibular Condyle. In: IFMBE Proceedings. Springer Berlin Heidelberg, pp. 438-441. ISBN 1680-0737

Hudha, K. and Jamaluddin, H. and Samin, P. M. and Rahman, R. A. (2008) Non-parametric linearised data driven modelling and force tracking control of a magnetorheological damper. International Journal of Vehicle Design 2008, 46 (2). pp. 250-269.

Wong, Kuan Yew and Komarudin, - (2008) Parameter tuning for ant colony optimization: A review. Proceedings of the International Conference on Computer and Communication Engineering 2008 . pp. 542-545.

Abd. Rahim, Erween and Kamdani, Kamaruddin and Sharif, Safian (2008) Performance evaluation of uncoated carbide tool in high speed drilling of Ti6Al4V. Journal of Advanced Mechanical Design, Systems and Manufacturing, 2 (4). pp. 522-531. ISSN 1881-3054

Nasution, Henry and Musa, Md Nor and Abdullah, Hayati and Wan Hassan, Mat Nawi and Baharain, Mohammad Akmal and Sulaiman, Sapiah and Mansour, Mohamed Khamis (2008) Potential energy saving by variable speed control of compressor for roof-top bus air conditioning system. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Mohd Samin, Pakharuddin and Jamaluddin, Hishamuddin and Abd Rahman, Roslan and Abu Bakar, Saiful Anuar and Hudha, Khisbullah (2008) Semi-active suspension for ride improvement using stability augmentation system control algorithm. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Shidong, Li and Abdul Hamid, Mohd. F. and Basaran, Cemal (2008) Simulating damage mechanics of electromigration and thermomigration. Simulation: Transactions of The Society for Modelling and Simulation Int., 84 (8-9). pp. 391-401. ISSN 0037-5497

Saqr, Khalid M. and Musa, Md. Nor (2008) Simulation of a novel hot-side heat exchanger for automobile exhaust-based thermoelectric generators using EFD. Journal Teknos-2K, 8 (1). pp. 17-26. ISSN 1411-4151

Olugu, Ezutah Udoncy and Wong, Kuan Yew (2008) Simulation Study on Lens Manufacturing Process Flow. Second Asia International Conference on Modelling & Simulation . pp. 806-811. ISSN 978-0-7695-3136-6/08

Tang, Howe Hing and Mailah, Musa (2008) Simulator for control of autonomous nonholonomic wheeled mobile robot. Journal of Applied Sciences, 8 (14). pp. 2534-2543. ISSN 1812-5654

Abdul Kadir, Mohammed Rafiq and Kamsah, N. and Sabudin, H. (2008) Stability of Talus Component in Total Ankle Arthroplasty. In: IFMBE Proceedings. Springer Berlin Heidelberg, pp. 453-456. ISBN 1680-0737

Purniawan, A. and Hamzah, Esah and Mohd Toff, Mohd Radzi (2008) Surface roughness and morphology analysis using an atomic force microscopy of polycrystalline diamond coated Si3N4 deposited by microwave plasma assisted chemical vapor deposition. Diffusion and Defect Data Pt.B: Solid State Phenomena, 136 . pp. 153-160. ISSN 1012-0394

Alan Chan, Kah Poh and Cheng , See Yuan and Mat Yamin, Ahmad Kamal and Jalaluddin, Ainil Jesita and Ishak, Iskandar Shah and Mansor, Shuhaimi (2008) The assessment of the effect of surface roughness on drag coefficient and aerodynamics features of loggerhead sea turtle carapace. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Ahmad Kamely, Mohamad and Mohd Yusof, Noordin and Ourdjini, Ali and Vellore Chelvaraj, Venkatesh (2008) The effectiveness of coatings when turning hardened cold work tool steel AISI D2 (60 HRC). International Journal of Machining and Machinability of Materials 2008, 4 (1). pp. 63-75. ISSN 1748-5711

Ishak, Mohamad Shaiful Ashrul and Mohd. Jaafar, Mohammad Nazri (2008) The influence of orifice insertion in radial swirling flow for low emissions combustion. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Abdul Ghani, Mohamad Pauzi and Abdul Rahim, M. N. (2008) The prediction of wake wash in the towing tank. Jurnal Mekanikal (26). pp. 129-140. ISSN 0127-3396

Abdul Kadir, Mohammed Rafiq and Osman, K. and Zainuddin, A. I. (2008) The Use of Mechanical Interlock in Dental Prosthesis. In: IFMBE Proceedings. Springer Berlin Heidelberg, pp. 457-460. ISBN 1680-0737

Mansour, M. Khamis and Musa, Md Nor and Mat Nawi, Wan Hassan (2008) Thermoeconomic optimization for a finned-tube evaporator configuration of a roof-top bus air-conditioning system. International Journal of Energy Research , 32 (4). 290-305 . ISSN 0363-907X

Abdul Hamid, M. F and S., Li and Basaran, C. (2008) Thermomigration in lead-free solder joints. International Journal of Materials and Structural Integrity, 2 (1-2). pp. 11-34. ISSN 1745-0055

Ahmad, Shaharudin and Abd Malik, Adi Maimun and Yupiter HP, Manurung and Rahmad, Junaidah and Mohd Nasir, Rizal Effendy and A. Bakar, Hamzah and Omar, Rohani (2008) Transverse strength of a semi-small waterplane area twin hull (swath). In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Phen, Chiak See and Wong, Kuan Yew (2008) Using statistical Design of Experiment to decide the effective parameter values for a new hybrid ant colony algorithm. International Journal of Applied Decision Sciences, 1 (3). pp. 282-304. ISSN 1755-8077

Abu Bakar, Saiful Anuar and Jamaluddin, H. and Rahman, R. A. and Hudha, K. (2008) Vehicle ride performance with semi-active suspension system using modified skyhook algorithm and current generator model. International Journal of Vehicle Autonomous Systems, 6 (3/4). pp. 197-221. ISSN 1471-0226

Lai, J.C. and Ani, F.N. and Hassan, A. (2008) Water absorption of lignocellulosic phenolic composites. Polymers and Polymer Composites , 16 (6). pp. 379-388. ISSN 09673911

Wiwiek Fatmawati, Wiwiek Fatmawati (2007) Analysis of product disassemblability using the disassembly evaluation chart methodology. Masters thesis, Universiti Teknologi Malaysia.

Ahmad, Md. Fauzi and Mohd Yusof, Sha’ri and Mohd Yusof, Noordin (2007) Comparative study of quality practices between Japanese and non-Japanese based electrical and electronics companies in Malaysia: a survey. Jurnal Teknologi (47 (A)). pp. 75-89. ISSN 0127-9696

Isa, Mohd. Akmal (2007) Development of ceramic cutting insert of aluminium oxide (Al2O3) and titanium carbide (TiC) for machining steel. Masters thesis, Universiti Teknologi Malaysia.

Lukman, Hafizi (2007) Estimation in spot welding parameters using genetic algorithm. Masters thesis, Universiti Teknologi Malaysia.

Abdul-Kadir, Mohammed Rafiq and Hansen, Ulrich N. (2007) Incorporation of interference fit and cyclic loading in simulation algorithm for better prediction of micromotion of femoral stems. Jurnal Teknologi (47 (A)). pp. 19-34. ISSN 0127-9696

Ishak, Mohamad Shaiful Ashrul and Mohd. Jaafar, Mohammad Nazri (2007) Noxious emission reduction from liquid fuel burner via air staging method. Jurnal Mekanikal, 24 . pp. 40-46. ISSN 0127-3396

Abdul Malick, Sharqiyah (2007) Organic and inorganic passivation performance on electroless nickel (LP). Masters thesis, Universiti Teknologi Malaysia.

Tamin, M. N. and Liew, Y. B. and Wagiman, A. N. R. and Loh, W. K. (2007) Solder joint fatigue in a surface mount assembly subjected to mechanical loading. IEEE Transactions on Components and Packaging Technologies, 30 . pp. 824-829. ISSN 1521-3331

Alias, Amran and Ahmad Nor, Nor Azlan and Said, Mohd Radzai (2007) The behaviour of square sandwich panel Part I: under static loading. Jurnal Teknologi (47 (A)). pp. 1-18. ISSN 0127-9696

Che Sidik, Nor Azwadi and Takahiko, Tanahashi (2007) Two-Phase Flow Simulation with Lattice Boltzmann Method. Two-Phase Flow Simulation with Lattice Boltzmann Method (24). pp. 68-79. ISSN 0127-3396

Saqr, Khalid M. and Musa, Md. Nor (2007) Conceptual design of a 160 W exhaust based thermoelectric generator for automotive waste heat recovery. In: International Conference of Engineering and ICT, 27-28 Nov., 2007, Melaka, Malaysia.

Tawi, Kamarul Baharin and Ariyono, Sugeng and Jamaluddin, Hishamuddin and Hussein, Mohamed and Supriyo, Bambang (2007) Adaptive neural network optimisation control of ICE for vehicle with continuously variable transmission. In: International Conference on Intelligent and Advanced Systems 2007. Institute of Electrical and Electronics Engineering (IEEE), pp. 257-262. ISBN 978-1-4244-1355-3

Zubir @ Zubair, Baizura (2007) Assemblability design efficiency (ADE) analyses for design for automatic assemblies. Masters thesis, Universiti Teknologi Malaysia.

Tamin, M. N. and Liew, Y. B. and Wagiman, A. N. R. and Loh, W. K. (2007) Assessment of solder joint fatigue performance using cyclic flexural loading. In: Proceedings of the IEEE/CPMT International Electronics Manufacturing Technology (IEMT) Symposium.

Hamzah, E. and Kanniah, M. and Harun, M. (2007) Effect of chromium addition on microstructure, tensile properties and creep resistance of as-cast Ti-48Al alloy. Journal of Materials Science, 42 (21). pp. 9063-9069. ISSN 0022-2461 (Print) 1573-4803 (Online)

Moftah Saeid, Fareg Saeid (2007) Effect of material structure machining characteristics of hypereutectic al-si alloy. Masters thesis, Universiti Teknologi Malaysia.

Mohammad Sofi @ Aziz, Azfi Zaihan (2007) Parametric system identification and active vibration control of vibrational structures using genetic algorithm. Masters thesis, Universiti Teknologi Malaysia.

Hussein, Mohamed and Moore, Philip and Jun-Sheng, Pu and Chi-Biu, Wong (2007) Quadrature encoder signal emulation for integrated real-virtual environments and systems. In: International Conference on Intelligent and Advanced Systems 2007. Institute of Electrical and Electronics Engineering (IEEE), pp. 1135-1140. ISBN 978-1-4244-1355-3

Mostofa Kamal, Md. Abu Hena (2007) Seakeeping analysis of a Malaysian fishing vessel. Masters thesis, Universiti Teknologi Malaysia.

Ahmad @ Manap, Mohd. Rizal (2007) Simulation and experimental analysis of an active vehicle suspension system. Masters thesis, Universiti Teknologi Malaysia.

M Yusuf, Md Afendi (2007) The Effect of Micro-Bubbles Elimination Prior Resin Infusion Process. Jurnal Mekanikal (24). 32-39. ISSN 0127-3396

Mansour, M. K. and Musa, M. N. and Wan Hassan , M. N. (2007) Thermal and economical optimization for a finned-tube, air-cooled condenser design of a roof-top bus air-conditioning system. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 221 . pp. 1363-1375. ISSN 0954-4062

Elghariani, Badreddin Giuma S. K. (2007) Transsient analysis of fluid structure interaction in straight pipe. Masters thesis, Universiti Teknologi Malaysia.

Nagarajan, R. and Yaacob, Sazali and Pandian, P. and Karthigayan, M. and Amin, Shamsudin and Khalid, Marzuki (2007) A real time marking inspection scheme for semiconductor industries. The international journal of advanced manufacturing technology, 34 (9-10). pp. 926-932. ISSN 0268-3768 (Print) 1433-3015 (Online)

Maslan, Mohamad Haidir (2007) Effects of absorbed hydrogen on fracture toughness of welded SA516 grade 70 steel. Masters thesis, Universiti Teknologi Malaysia.

Basaruddin, Khairul Salleh (2007) Ratchetting of composite pipes. Masters thesis, Universiti Teknologi Malaysia.

Su, Massharudin (2007) Study on thermal characteristic of oscilloscope with new from factor design. Masters thesis, Universiti Teknologi Malaysia.

M. A., Kamely and M. Y., Noordin and V. C., Venkatesh (2007) The Effect of Multiple Pass Cutting on Surface Integrity when Hard Turning of AISI D2 Cold Work Tool Steel. International Journal of Precision Technology, 1 (1). pp. 97-105. ISSN 1755-2060

Noordin, M. Y. and Tang, Y. C. and Kurniawan, D. (2007) The use of TiAlN coated carbide tool when finish machining hardened stainless steel. International Journal of Precision Technology, 1 (1). pp. 21-29. ISSN 1755-2079

Hamzah, Esah and Kanniah, M. and Harun, M. (2007) Creep Behavior of As-Cast Ti-48Al-2Cr Intermetallic Alloy for Aerospace and Automotive Applications. Materials and Manufacturing Processes, 22 (7). pp. 793-797. ISSN 1532-2475

Pitowarno, E. and Mailah, Musa (2007) Control of mobile manipulator using resolved acceleration with iterative-learning-proportional-integral active force control. International Review of Mechanical Engineering, 1 (5). pp. 549-558.

Ochsner, Andreas and Belova, I. V. and Muthubandara, N. and Murch, G. E. (2007) Modelling of oxygen diffusion and segregation at interfaces in Ag-MgO composites. Defect and Diffusion Forum, 266 . pp. 29-38. ISSN 1012-0386

Che Sidik, Nor Azwadi (2007) The development of thermal lattice Boltzmann models in incompressible limit. The development of thermal lattice Boltzmann models in incompressible limit, 3 (2). pp. 193-202.

Jamaludin, Khairur Rijal and Muhamad, Norhamidi and Ab. Rahman, Mohd Nizam and M. Amin, Sri Yulis (2007) Temperature influence to the injection molding of fine and coarse SS316l powder with PEG, PMMA and stearic acid binder system. In: Proceeding of Malaysian Symposium on Advances in Powder Metallurgy & Particulate Materials 2007, 21-22 August 2007, Faculty of Mechanical Engineering, University Technology MARA.

Mansour, M. Khamis and Musa, Md. Nor and Wan Hassan, Mat Nawi (2007) Thermoeconomic optimization for a finned-tube evaporator configuration of a roof-top bus air-conditioning system. International journal of energy research . pp. 1-16. ISSN 1099-114X

M. Amin, Sri Yulis and Muhamad, Norhamidi and Jamaludin, Khairur Rijal and Abdullah, Shahrir and Ab. Rahman, Mohd Nizam (2007) Rheological investigation of mim feedstocks prepared with different particle sizes. In: World Engineering Congress 2007, 5-9 August 2007, Pulau Pinang, Malaysia.

Shamsudin, Syariful Syafiq (2007) The development of autopilot system for an unmanned aerial vehicle (UAV) helicopter model. Masters thesis, Universiti Teknologi Malaysia.

K. Seveen, K. Muniswaran (2007) Experimental study on hard turning of hardened tool steel with coated carbide cutting tools. Masters thesis, Universiti Teknologi Malaysia.

Mat Saad, Khairul Anuar (2007) Manoeuvring control for pusher barge in inland waterway. Masters thesis, Universiti Teknologi Malaysia.

M. Saqr, Khalid and Musa, Md. Nor (2007) State of the art of thermoelectric generators for waste heat recovery applications. Jurnal Teknos-2k, 7 (2). pp. 1-10. ISSN 1411 - 4151

Elshwain, Amad Alddein (2007) A study of lapping parameters to reduce polishing time of optical glass. Masters thesis, Universiti Teknologi Malaysia.

Jamaludin, Khairur Rijal and Abdul Talib, Hayati @ Habibah and Tan, Chiaw Hooi (2007) An improvement to the performance measurement system of the logistics operation. Journal The Institution of Engineers Malaysia, 68 (2). pp. 41-46. ISSN 0126-513X

Abu, Risal and Md. Tap, Masine (2007) Attribute based feature recognition for machining features. Jurnal Teknologi A, 46 (A). pp. 87-103. ISSN 0126-9797

Thangavelu, T. R. Anbarasan (2007) Evaluation of coolant concentration on the machiniability of carbon steel during end milling. Masters thesis, Universiti Teknologi Malaysia.

Sia, Toh Ching and Velautham, Sanjayan and Darus, Amer Nordin (2007) Exergetic optimization of a flat plate solar collector design. International Energy Journal, 8 (2). pp. 125-130. ISSN 1513-718X

Ramli, Nabila and Mansor, Shuhaimi and Jamaluddin, Hishamuddin and Faris, Waleed Fekry (2007) Identification of aerodynamic coefficients of ground vehicles using neural network. In: Intelligent Vehicles Symposium, 2007 IEEE, 13-15 June 2007, Istanbul.

Che Zainal Abidin, Nik Mohd Farid (2007) Incorporating design for manufacture and assembly methodologies into the design of a modified spark plug. Masters thesis, Universiti Teknologi Malaysia.

Ibrahim, Kamarulzaman (2007) Numerical analysis on thermal performanace of staggered pin-fin assembly. Masters thesis, Universiti Teknologi Malaysia.

Wong, Wai Hing and Mohd. Ghazali, Normah (2007) Numerical Simulation Of A Microchannel For Microelectronic Cooling. Jurnal Teknologi A, 46 (A). pp. 1-16. ISSN 0127-9696

Wong, Hai Hing and Mohd Ghazali, Normah (2007) Numerical simulation of a microchannel for microelectronic cooling. Jurnal Teknologi . pp. 1-16.

Aspar, Mohd. Hanip (2007) Tahap pengamalan pengurusan keselamatan dalam industri kecil dan sederhana. Masters thesis, Universiti Teknologi Malaysia.

Chuan, Chin Wong and Ani, Farid Nasir (2007) The Economic Evaluation Of The Production Of Oil-Palm-Shell-Based Phenol. Jurnal Teknologi D, 46 (A). pp. 43-52. ISSN 0127-9696

Ani, Farid Nasir and Chuan, Chin Wong (2007) The economic evaluation of the production of oil–palm–shell–based phenol. Jurnal Teknologi . pp. 43-52.

Misha, Suhaimi and Darus, Amer Nordin (2007) Variational method in the design of an optimum solar water heater storage tank. Jurnal Mekanikal (23). pp. 62-73.

Venkatesh, V. C. and S. , Izman (2007) Development of a Novel Binderless Diamond Grinding Wheel for Machining IC Chips for Failure Analysis. Journal of Materials Processing Technology, 185 (1-3). pp. 31-37. ISSN 0924-0136

V. C., Venkatesh and S., Izman (2007) Development of a novel binderless diamond grinding wheel for machining IC chips for failure analysis. Journal of Materials Processing Technology, 185 . pp. 131-137. ISSN 0924-0136

M. Y., Noordin and V. C., Venkatesh and Sharif, S. (2007) Dry Turning of Tempered Martensitic Stainless Tool Steel using Coated Cermet and Coated Carbide Tools. Journal of Materials Processing Technology, 185 (1-3). pp. 89-90. ISSN 09240136

Suardi, Khairmen and Hamzah, E. and Ourdjini, A. and Venkatesh, V. C. (2007) Effect of heat treatment on the diffusion coefficient of hydrogen absorption in gamma-titanium aluminide. Journal of Materials Processing Technology, 185 (1-3). pp. 106-112. ISSN 0924-0136

S., Izman and V. C., Venkatesh (2007) Gelling of Chips During Vertical Surface Diamond Grinding of BK7 Glass. Journal of Materials Processing Technology, 185 . pp. 178-183. ISSN 0924-0136

A. K., Mohammed Rafiq and K., Nazri (2007) Primary Hip Stem Stability: The Effect of Bone Pathology on Micromotion. In: 2nd International conference on the Mathematical Science 2007.

Nusyirwan, Istas Fahrurrazi and Bil, Cees (2007) Methods of aircraft trajectory optimisation in air combat. Australian and New Zealand Industrial and Applied Mathematics Journal, 47 . C649-C664. ISSN 1446-8735

Tan, Chek Zin (2007) An experimental and field study of cavitation detection in pump. Masters thesis, Universiti Teknologi Malaysia.

Pang, Hooi San (2007) Development of low coefficient of thermal expansion composite substrate for electronic packaging using finite element method. Masters thesis, Universiti Teknologi Malaysia.

Sharif, S. and Rahim, E. A. (2007) Performance of Coated- and Uncoated-Carbide Tools When Drilling Titanium Alloy-Ti–6Al4V. Journal of Materials Processing Technology, 185 (1-3). pp. 72-76. ISSN 09240136

Musa, Md. Nor and Idris, Mohd. Hasbullah (2007) Development of Fuel Cell Powered Automotive Thermal Comfort and Refrigeration System. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Idris, Ani and Mat Zain, Norashikin and M. Y., Noordin (2007) Synthesis, Characterization and Performance of Asymmetric Polyethersulfone (PES) Ultrafiltration Membranes with Polyethylene Glycol of Different Molecular Weights as Additives. Desalination, 207 . pp. 324-339. ISSN 0011-9164

Idris, Ani and Mat Zain, Norashikin and M.Y. , Noordin (2007) Synthesis, characterization and performance of asymmetric polyethersulfone (PES) ultrafiltration membranes with polyethylene glycol of different molecular weights as additives. Desalination, 207 . pp. 324-339. ISSN 0011-9164

Idris, A. and Mat Zain, N. and Nordin, M. Y. (2007) Synthesis, characterization and performance of asymmetric polyethersulfone (PES) ultrafiltration membranes with polyethylene glycol of different molecular weights as additives. Desalination, 207 . pp. 324-339. ISSN 0011-9164

Mailah, M. and As'arry, A and Hussein, M and Zain, M. Z Md and Abdullah, M. Y H and Ahmad, R (2007) Development of hand-arm model rig for tremor excitation. International Journal of Simulation Modelling, 6 . pp. 25-36. ISSN 1726-4529

Ali, Mubarak and Hamzah, Esah and Mohd Toff, Mohd Radzi (2007) Deposition and characterization of TiN-coated steels at various N 2 gas flow rates with constant etching by using capvd technique. Surface Review and Letters, 14 (1). pp. 93-100. ISSN 0218-625X

Che Sidik, Nor Azwadi and Takahiko, Tanahashi (2007) Three-Dimensional Thermal Lattice Boltzman Simulation of Natural Convection in a Cubic Cavity. International Journal of Modern Physics B, 21 . pp. 87-96. ISSN 0217-9792

Ahmad Fitriadhy, Ahmad Fitriadhy (2007) Seakeeping evaluation of semi-swath vessel in head-seas using time domain simulation. Masters thesis, Universiti Teknologi Malaysia.

Che Sidek, Nor Azwadi and Takahiko, Tanahashi (2007) Three-dimensional thermal lattice boltzmann simulation of natural convection in a cubic cavity. International Journal of Modern Physics B, 21 (1). pp. 87-96. ISSN 0217-9792

Ali, Mubarak (2007) Influence Of Processing Parameters On The Properties Of Tin Coatings Deposited On Tool Steels Using Cathodic Arc Physical Vapour Deposition Technique. PhD thesis, Universiti Teknologi Malaysia .

Mishuris, Gennady and Ochsner, Andreas (2007) 2D modelling of a thin elasto-plastic interphase between two different materials: Plane strain case. Composite Structures, 80 (3). pp. 361-372. ISSN 0263-8223

Ochsner, Andreas and Stasiek, Michal and Mishuris, Gennady and Gracio, Jose (2007) A new evaluation procedure for the butt-joint test of adhesive technology: determination of the complete set of linear elastic constants. International Journal of Adhesion and Adhesives, 27 (8). pp. 703-711. ISSN 0143-7496

Wong, Wai Peng and Jaruphongsa, Wikrom and Lee, Loo Hay and Wong, Kuan Yew (2007) A preliminary study on using Data Envelopment Analysis (DEA) in measuring supply chain efficiency. International Journal of Applied Systemic Studies , 1 (2). pp. 188-207.

See, Phen Chiak and Wong, Kuan Yew (2007) A review on ant colony optimization algorithm for solving facility layout problems formulated as quadratic assignment problems. 2nd International Conference on Mathematical Sciences .

Wong, Kuan Yew and Tham, Chien Yeh (2007) A simulation study on the manufacturing of electronic chassis. Rio's International Journal on Sciences of Industrial and Systems Engineering and Management, 1 (1). pp. 29-54. ISSN 1982-6443

Raja Hamzah, R. I. and Mba, D. (2007) Acoustic Emission and Specific Film Thickness for Operating Spur Gears. Journal of Tribology , 129 (4). pp. 860-867. ISSN 0742-4787

Wong, Kuan Yew and Ahmad, Robiah and Komarudin, - (2007) An Evaluation of Parameters Tuning Methods in Metaheuristic Algorithms. In: Regional Conference on Advanced Processes and Systems in Manufacturing (APSIM) 2007, 2007, Putrajaya.

Ochsner, Andreas and Gracio, Jose (2007) An evaluation of the elastic properties of an adhesive layer using the tensile-butt joint test: Procedures and error estimates. International Journal of Adhesion and Adhesives, 27 (2). pp. 129-135. ISSN 0143-7496

Ali, Mubarak and Hamzah, Esah and Hj Mohd Toff, Mohd Radzi (2007) Deposition and characterization of TiN-coated steels at various N 2 gas flow rates with constant etching by using capvd technique. Surface Review and Letters , 14 (1). pp. 93-100. ISSN 0218-625X

Khamis Mansour, M. and Musa, Md. N. and Hassan, M. N. W. and Abdullah, H. and Saqr, K. M. (2007) Development of a novel control strategy for a multiple-circuit roof-top bus air-conditioning system in hot humid countries. International Journal of Mechanical and Materials Engineering, 2 . pp. 200-211. ISSN 1823-0334

Noordin, M. Y. and Venkatesh, V. C. and Sharif, Safian (2007) Dry turning of tempered martensitic stainless tool steel using coated cermet and coated carbide tools. Journal of Materials Processing Technology, 185 (1-3). pp. 83-90. ISSN 0924-0136

Ahmad, S. N. A. S. and Hashim, J. and Ghazali, M. I. (2007) Effect of porosity on tensile properties of cast particle reinforced MMC. Journal of Composite Materials, 41 (5). pp. 575-589. ISSN 0021-9983

B. W., Wan Nik and M. A., Maleque and Ani, Farid Nasir and Hassan, Masjuki (2007) Experimental Investigation on System Performance Using Palm Oil as Hydraulic Fluid. Industrial Lubrication and Tribology, 59 (5). pp. 200-208. ISSN 0036-8792

Fiedler, T. and Ochsner, Andreas (2007) Finite element analysis of the temperature dependent conductivity of metallic hollow sphere structures. The International Journal of Multiphysics, 1 (3). pp. 283-289. ISSN 1750-9548

Niw , Chang Chee and Abu Bakar, Abd Rahim (2007) Finite Element Modeling of Arc Welded Joints. Jurnal Mekanikal (23). pp. 15-30. ISSN 0127-3396

Oliveira, Branca F. de and Cunda, Luiz A. B. da and Oschner, Andreas and Creus, G. J. (2007) Finite element simulation of compression tests on cellular metals. APMTAC, Portugal . ISSN 1230-3534

M.Y. , Noordin and Kurniawan, D. and Sharif, S. (2007) Hard Turning of Stainless Steel using Wiper Coated Carbide Tool. International Journal of Precision Technology, 1 (1). pp. 75-84. ISSN 1755-2060

Ramli, N. and Mansor, S. and Jamaluddin, H. and Faris, W. F. (2007) Identification of aerodynamic coefficients of ground vehicles using neural network. IEEE Intelligent Vehicles Symposium, Proceedings . pp. 50-55.

Chong, C.W. and Chong, S.C. and Wong, Kuan Yew (2007) Implementation of KM strategies in the Malaysian telecommunication industry: an empirical analysis. VINE: The Journal of Information and Knowledge Management Systems, 37 (4). pp. 452-470. ISSN 0305-5728

Hamzah, Esah and Qourdjini, Ali and Ali, Mubarak and Parvez, Akhter and Mohd Toff, Mohd Radzi and Abdul Hamid, Mansor (2007) Influence of nitrogen flow rate on friction coefficient and surface roughness of tin coatings deposited on tool steel using arc method. Surface Review and Letters , 14 (5). pp. 1007-1013. ISSN 0218-625X

Abdul Kadir, Mohammed Rafiq and Kamsah, Nazri and Tamin, Mohd. Nasir and Lee, Faisal Abidin (2007) Interface Micromotion Failure Simulation of Cementless Hip Prosthesis. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Nordin, N.N. and Zainuddin, Z.M. and Wong, Kuan Yew (2007) Metaheuristics for solving facility layout problems: concepts and trends. 2nd International Conference on Mathematical Sciences .

Gromada, M. and Mishuris, Gennady and Ochsner, A. (2007) Necking in the tensile test. Correction formulae and related error estimation. Archives of Metallurgy and Materials , 52 (2). pp. 231-238. ISSN 1733-3490

Fiedler, T. and Ochsner, A. (2007) On the Thermal Conductivity of Adhesively Bonded and Sintered Hollow Sphere Structures (HSS). Materials Science Forum, 553 . pp. 39-44. ISSN 978-0-87849-438-5

Ayob, Amran and Elbasheer, M. Kabashi (2007) Optimum autofrettage pressure in thick cylinders. Jurnal Mekanikal (24). pp. 1-14. ISSN 0127-3396

Jamaluddin, Hishamuddin and Abd. Samad, M. F. and Ahmad, Robiah and Yaacob, M. S. (2007) Optimum grouping in a modified genetic algorithm for discrete-time, non-linear system identification. Journal of Systems and Control Engineering, 221 (7). pp. 975-989. ISSN 0959-6518

Jamaluddin, H. and Samad, M. F. A. and Ahmad, R. and Yaacob, M. S. (2007) Optimum grouping in a modified genetic algorithm for discrete-time, non-linear system identification. Proceedings of the Institution of Mechanical Engineers. Part I: Journal of Systems and Control Engineering, 221 . pp. 975-989. ISSN 0959-6518

Oliveira, B. F. and Cunda, L. A. B. and Oschner, Andreas and Creus, G. J. (2007) Parameter identification to simulate a tensile test applying gurson damage model. APMTAC, Portugal . ISSN 1230-3534

Sharif, Safian and Abd. Rahim, Erween (2007) Performance of coated- and uncoated-carbide tools when drilling titanium alloy-Ti-6Al4V. Journal of Materials Processing Technology , 185 (1-3). pp. 72-76. ISSN 0924-0136

Syed Hassan, S.A.H. and Md Sirat, R. and Wong, Kuan Yew and Abdul Rani, M.R. (2007) Potential Critical Success Factors (CSFs) for Total Safety Management (TSM) in Malaysian Small and Medium Industries (SMIs). Proceedings of the International Conference on Ergonomics . pp. 61-65.

Lee, Ing Yi and Mohd. Yusof, Sha'ri (2007) Product quality improvement through poka yoke technique. Jurnal Mekanikal (23). pp. 74-82. ISSN 0127-3396

Y. M. , Sam and K. , Hudha and J. S. H. , Osman (2007) Proportional-integral sliding mode control of a hydraulically actuated active suspension system: force tracking and disturbance rejection control on non-linear quarter car model. International Journal of Vehicle Systems Modelling and Testing, 2 (4). pp. 391-410.

Mailah, M. and Priyandoko, G. (2007) Simulation of a suspension system with adaptive fuzzy active force control. International Journal of Simulation Modelling , 6 (1). pp. 25-36. ISSN 1726-4529

Teo, Han Fui and Abd. Rahman, Roslan (2007) Statics and dynamics structural analysis of a 4.5 ton truck chassis. Jurnal Mekanikal (24). pp. 56-67. ISSN 0127-3396

Abd. Rahman, Roslan and Teo, Han Fui (2007) Statistic and Dynamics Structural Analysis of a 4.5 Ton Truck Chassis. Jurnal Mekanikal (24). pp. 56-67. ISSN 0127-3396

Wong, Wai Peng and Wong, Kuan Yew (2007) Supply chain performance measurement system using DEA modeling. Industrial Management & Data Systems, 107 (3). pp. 361-381. ISSN 0263-5577

Abdul Kadir, Mohammed Rafiq and Hansen, Ulrich N. (2007) The effect of physiological load configuration on interface micromotion in cementless femoral stems. Jurnal Mekanikal, 23 . pp. 50-61. ISSN 0127-3396

Belova, Irini V. and Murch, Graeme E. and Fiedler, Thomas and Ochsner, Andreas (2007) The lattice Monte Carlo method for solving phenomenological mass and heat transport problem. Diffusion Fundamentals, 4 . pp. 1-23. ISSN 1862-4138

Noordin , M. Y. and Y., C. Tang and Kurniawan, D. (2007) The use of TiAIN coated carbide tool when finish machining hardened stainless steel. International Journal Precision Technology, 1 (1). pp. 21-29. ISSN 1755-2060

Mansour, M. Khamis and Musa, Md. Nor and Hassan, M. N. W. and Abdullah, H. (2007) Theoretical and experimental simulation of roof-top bus multiple-circuit air-conditioning system performance. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science , 221 (12). pp. 1665-1677. ISSN 0954-4062

Khamis Mansour, M. and Musa, M. N. and Wan Hassan, M. N. (2007) Thermal and economical optimization for a finned-tube, air-cooled condenser design of a roof-top bus air-conditioning system. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 221 (11). pp. 1363-1375. ISSN 0954-4062

Rahim, E. A. and Shariff, Safian (2007) Tool failure modes and wear mechanism of coated carbide tools when drilling Ti-6AI-4V. International Journal Precision Technology, 1 (1). pp. 30-39. ISSN 1755-2079

Rahim, E.A. and Sharif , S. (2007) Tool failure Modes and Wear Mechanism of Coated Carbide Tools when Drilling Ti-6Al-4V. International Journal of Precision Technology , 1 (1). pp. 30-39. ISSN 1755-2060

Misha, Suhaimi and Darus, Amer Nordin (2007) Variational Method In The Design of an Optimum Solar Water Heater Storage Tank. Jurnal Mekanikal, 23 . pp. 62-73. ISSN 0127-3396

Mailah, Musa and Jamaluddin, Hishamuddin and Mohd Zain, Mohd Zarhamdy and Priyandoko, Gigih and Abdul Rahim, Mohammad Akmal Baharain (2006) Development of An Extremely Robust Automotive Suspension System Using Intelligent Active Force Control. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Ahmad, Mohd Zamani and Abdul Kader, Abdul Saman and Ahmat, Ahmat Narawi and Idris, Jamaliah (2006) A fuzzy application on a development planning model for a container terminal. Jurnal Teknologi Siri A, 45 (A). pp. 13-29. ISSN 0127-9696

Abu Bakar, Abd Rahim and Abdul Hamid, Mohd Kameil and Ouyang, Huajiang (2006) A new prediction methodology for dynamic contact pressure distributions in a disc brake. Jurnal Teknologi Siri A, 45 (A). pp. 1-11. ISSN 0127-9696

Ali, Mubarak and Hamzah, Esah and Mohd Toff, Mohd Radzi (2006) Effect of Substrate Bias on Friction Coefficient, Adhesion Strength and Hardness of Tin-Coated Tool Steel. Surface Review and Letters, 13 (6). pp. 763-771. ISSN 0218-625X

Saharin, Sanisah (2006) Emissions reduction from an oil burner by air staging. Masters thesis, Universiti Teknologi Malaysia.

Ariyono, Sugeng and Tawi, Kamarul Baharin and Jamaluddin, Hishamuddin and Supriyo, Bambang (2006) Engine Speed Control using Online ANN for Vehicle with EMDAP-CVT. Jurnal Mekanikal, 22 . pp. 39-52. ISSN 0127-3396

Ishak, Iskandar Shah and Mat, Shabudin and Mat Lazim, Tholudin and Muhammad, Mohd. Khir and Mansor, Shuhaimi and Awang, Mohd Zailani (2006) Estimation of Aerodynamic Characteristics of a Light Aircraft. Jurnal Mekanikal (22). pp. 64-74. ISSN 0127-3396

Zakaria, Kamarul Ariffin (2006) Impact analysis of fibreglass reinforced composites. Masters thesis, Universiti Teknologi Malaysia.

Mohammad, Roslina (2006) Impact properties of cirular beam under lateral loading. Masters thesis, Universiti Teknologi Malaysia.

Wan Abdul Rahaman, Wan Emri (2006) Performance evaluation of coated ceramic cutting tools with T-land edge preparation when turning hardened tool steel. Masters thesis, Universiti Teknologi Malaysia.

Supriyo, Bambang and Tawi, Kamarul Baharin and Jamaluddin, Hishamuddin and Ariyono, Sugeng (2006) Position Control for Pulley Axial Movement of Electro-Mechanical Dual Acting Pulley Continuously Variable Transmission System. Jurnal Mekanikal (22). pp. 89-102. ISSN 0127-3396

Maimun, Adi and Yaakob, Omar and Md. Ahm, Kamal and Ng, Chee Wei (2006) Seakeeping Analysis of a Fishing Vessel Operating in Malaysian Water. Jurnal Mekanikal (22). pp. 103-114. ISSN 0127-3396

Abu Bakar, Abd Rahim and Abdul Hamid, Mohd Kameil and Dzakaria, Afandi and Abdul Ghani, Badri and Mohamad, Maziah (2006) Stability Analysis of Disc Brake Squeal Considering Temperature Effect. Jurnal Mekanikal, 22 . pp. 26-38. ISSN 0127-3396

Maharsi, Indra Wening (2006) Structural design and analysis of a microturbine compressor. Masters thesis, Universiti Teknologi Malaysia.

Hussain, Ahmad and Ani, Farid Nasir and Darus, Amer Nordin and Ahmed, Zainal (2006) Thermogravimetric and thermochemical studies of Malaysian oil palm shell waste. Jurnal Teknologi Siri A, 45 (A). pp. 43-53. ISSN 0127-9696

Kamsir, Abdul Sukur (2006) Wire electrical discharge machining of Ti-48Al intermetalic alloys using taguchi approach. Masters thesis, Universiti Teknologi Malaysia.

Mohamed, Zulkifli (2006) Mechatronic design and development of a robotic arm. Masters thesis, Universiti Teknologi Malaysia.

Hassan, Mas Ayu (2006) Performance evaluation of wire electro-discharge machining on tungsten carbide. Masters thesis, Universiti Teknologi Malaysia.

Md. Ani, Sarizal (2006) Physical behaviour of powder ceramic part using cold isostatic pressing (CIP) processes. Masters thesis, Universiti Teknologi Malaysia.

Olanrewaju, Oladokun Sulaiman (2006) Sustainable maintenance of navigation channel. Masters thesis, Universiti Teknologi Malaysia.

Maarof, Mohd. Rashidi (2006) The effect of nodularisation parameters on the quality of ductile iron. Masters thesis, Universiti Teknologi Malaysia.

Misha, Suhaimi (2006) Variational method in the design of an optimum solar water heater storage tank. Masters thesis, Universiti Teknologi Malaysia.

Ali, Mubarak and Hamzah, Esah and Mohd Toff, Mohd Radzi (2006) Effect of substrate bias voltage on the microstructural and mechanical properties of tin-coated HSS synthesized by capvd technique. Surface Review and Letters, 13 (5). pp. 621-633. ISSN 0218-625X

Zadry , Hilma Raimona and Mohd Yusof, Sha'ri (2006) Total Quality Management and Theory of Constraints Implementation in Malaysian Automotive Suppliers: A Survey Result. Total Quality Management, 17 (8). pp. 999-1020. ISSN 0954-4127, 1360-0613

Zadry , Hilma Raimona and Mohd Yusof, Sha'ri (2006) Total Quality Management and Theory of Constraints Implementation in Malaysian Automotive Suppliers: A Survey Result. Total Quality Management & Business Excellence, 17 (8). pp. 999-1020. ISSN 1478-3363

Zadry , Hilma Raimona and Mohd Yusof, Sha'ri (2006) Total Quality Management and Theory of Constraints Implementation in Malaysian Automotive Suppliers: A Survey Result. Total Quality Management, 17 (8). pp. 999-1020. ISSN 0954-4127

Tam, Wee Kong (2006) Comfort analysis in commercial vehicle’s passenger seat. Masters thesis, Universiti Teknologi Malaysia.

Ali, Mubarak and Hamzah, Esah and Mohd Toff, Mohd Radzi (2006) Effect of metal ion etching on the tribological, mechanical and microstructural properties of TiN-coated D2 tool steel using cae PVD technique. Surface Review and Letters, 13 (4). pp. 413-421. ISSN 0218-625X

Yaakob, Omar and Tengku Ab Rashid,, Tengku Mohd Ariff and Abdul Mukti, Mohamad Afifi (2006) Prospects for Ocean Energy in Malaysia. International Conference on Energy and Environment 2006 (ICEE 2006) .

Che Sidik, Nor Azwadi and Takahiko, Tanahashi (2006) Simplified Thermal Lattice Boltzman Incompressible Limit. International Journal of Modern Physics B, 20 (17). pp. 2437-2449. ISSN 1793-6578

Che Sidik, Nor Azwadi and Takahiko, Tanahashi (2006) Simplified thermal lattice boltzmann in incompressible limit. International Journal of Modern Physics B, 20 (17). pp. 2437-2449. ISSN 0217-9792

Zaman @ Bujang, Izzuddin and Abd. Rahman, Roslan (2006) Application Of Dynamic Correlation Technique And Model Updating On Truck Chassis. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Sahari, Barkawi and Ali, Yusoff and Ahmadun, Fakhru’l-Razi and Abdullah, Shahrir and Hassan, Masjuki and Aris, Ishak and Abdullah, Muhamad Adlan and Ahmad, Mohd. Fauzy and Chelliah, V. and Taha, Zahari and Aziz, Abd. Rashid and Musa, Md. Nor and Chuah, T. G. and Mariun, Norman and Ku Hamid, Ku Halim and Radhakrishnan, V. R. (2006) Compressed Natural Gas Passenger Vehicle Development – Issues and Challenges. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Ishak, Iskandar Shah (2006) Computational Fluid Dynamics Simulation and Wind Tunnel Testing on Microlight Model. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Abdul Aziz, Azhar and Ali, Mas Fawzi (2006) Conceptual Development of a Pressure-swirl Injector For a Two-stroke GDI Engine. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Ab. Wahab, Abas and Mamat, Rosbi and Shamsudin, Syariful Syafiq (2006) Control System Design for An Autonomous Helicopter Model in Hovering Using Pole Placement Method. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Supriyo, Bambang and Tawi, Kamarul Baharin and Jamaluddin, Hishamuddin and Ariyono, Sugeng (2006) DC Motor Position Control for Pulley Axial Movement of an Electromechanical Dual Acting Pulley (EMDAP) CVT System. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Mat Saman, Muhamad Zameri and Zakuan, Norhayati (2006) End-of-Life Vehicle Directive: A Key Element to the Vehicle Design Process. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Ariyono, Sugeng and Tawi, Kamarul Baharin and Jamaluddin, Hishamuddin and Supriyo, Bambang (2006) Engine Speed Control Using Artificial Neutral Network for Vehicle Equipped with Electromechanical CVT. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Abdul Aziz, A. and Abdul Latiff, Z. and Mohd Ali, M. Fawzi and Mohammad Said, M.Farid and Said, M. (2006) Enhancing the Performance of a 125 cc Single-cylinder, Aircooled, Gasoline Two-stroke Engine. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Wahab, A. A. and Ismail, M. Hafiz (2006) Estimating Vertical Drag on Helicopter Fuselage during Hovering. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Ishak, Iskandar Shah and Mat, Shabudin and Mat Lazim, Tholudin and Muhammad, Mohd. Khir and Mansor, Shuhaimi and Awang, Mohd Zailani (2006) Experimental and simulation Studies of a Two Seater Light Aircraft. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Nik Mohd., Nik Ahmad Ridhwan (2006) Feasibility study on improving of 5-seater helicopter forward flight speed. Masters thesis, Universiti Teknologi Malaysia.

N. A. R., Nik Mohd and A. A., Wahab (2006) Feasibility Study on Improving of Helicopter Forward Flight Speed via Modification of the Blade Dimension and Engine Performance. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Othman, Muhammad Firdaus (2006) Flow and heat transfer analysis on spiral counter flow heat recirculating burner. Masters thesis, Universiti Teknologi Malaysia.

Ammoo, Mohd. Shariff and Dahalan, Md. Nizam (2006) Micro Air Vehicle: Technology Review and Design Study. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Ishak, Mohamad Shaiful Ashrul and Mohd. Jaafar, Mohammad Nazri (2006) Noxious Emission Reduction from Liquid Fuel Burner via Air Staging Method. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Nik Mohdi , Nik Ahmad Ridhwan and Ab. Wahabii, Abas (2006) Numerical Analysis of an Isolated Main Helicopter Rotor in Hovering and Forward Flight. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Wahab, A. A. and M. Ali, M. S. (2006) Numerical Study on the Transition Performance of a Scale Model Helicopter from Hovering to Vertical Autorotation. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Shamsuddin, S. M. and Ahmed , M. A. and Smian, Y. (2006) NURBS skinning surface for ship hull design based on new parameterization method. International Journal of Advanced Manufacturing Technology, 28 (9 - 10). pp. 936-941. ISSN 0268-3768

Wahab, A. A. and M. Ali, M. S. (2006) Preliminary Experimental Investigation on Autorotation Performance of Scale Model Helicopter in Vertical Manoeuvre. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Muhamad, Sallehuddin (2006) Simulation of the Tanjung Kupang Air Crash. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Wahab, A. A. and Mamat, Rosbi and Shamsudin, Syariful Syafiq (2006) The Development of Autopilot System for an Autonomous UAV Helicopter Model. In: 1st Regional Conference on Vehicle Engineering & Technology, 3-5 July 2006, Kuala Lumpur, Malaysia.

Mohd Ghazali, Normah and Abdul Aziz, Azhar and Abu Bakar, Rosli and Che Sidek, Azwadi (2006) Thermoacoustic Regfrigeration From Waste Heat. Project Report. Universiti Teknologi Malaysia. (Unpublished)

IMPERIAL INNOVATIONS LTD. [GB/GB]; Electrical and Electronic Engineering Building, Imperial College, London SW7 2BT (GB) (All Except US). (2006) Flow control device for a turbocharger. WO/2006/061588 .

Yaakob, Omar and Zainudin, Norazimar and Abdul Malik, Adi Maimun and Samian, Yahya and Palaraman, Robiahtul Adawiah (2006) Development Of A Malaysian Ocean Wave Database And Models For Engineering Purposes. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Abd. Rahim, Shayfull Zamree (2006) Analyses of material flow in two and three-plate molds for mold design selection. Masters thesis, Universiti Teknologi Malaysia.

Hussain, Ahmad and Ani, Farid Nasir and Sulaiman, Norzalia and Adnan, Mohammed Fadzil (2006) Combustion modelling of an industrial municipal waste combustor in Malaysia. International journal of environmental studies, 63 (3). pp. 313-329. ISSN 0020-7233

Hussain, Ahmad and Ani, Farid Nasir and Sulaiman, Norzalia and Fadzil Adnan, Mohammed (2006) Combustion modelling of an industrial municipal waste combustor in Malaysia. International Journal of Environmental Studies, 63 (3). pp. 313-329.

Hussain, A. and Ani, Farid Nasir and Sulaiman, N. and Fadzil Adnan, M. (2006) Combustion modelling of an industrial municipal waste combustor in Malaysia. International Journal of Environmental Studies, 63 . pp. 313-329. ISSN 0020-7233

Dolah, Rozzeta (2006) Etching performance of silicon wafers with redesigned etching drum. Masters thesis, Universiti Teknologi Malaysia.

Tang, H. H. and Mailah, Musa and A. Jalil, M. Kasim (2006) Robust Intelligent Active Force Control Of Nonholonomic Wheeled Mobile Robot. Jurnal Teknologi D, 44 (D). pp. 49-64. ISSN 0127-9696

Zakaria, Hafizawati (2006) Crushworthiness of polymeric foam used as core composite sandwich structure. Masters thesis, Universiti Teknologi Malaysia.

Wan Ibrahim, Wan Abd. Rahman Assyahid (2006) Design and development of thermodynamics apparatus using design for manufacture and assembly (DFMA) methodology. Masters thesis, Universiti Teknologi Malaysia.

Wong, Kuan Yew and Aspinwall, Elaine (2006) Development of a knowledge management initiative and system: A case study. Expert System with Applications, 30 (4). pp. 633-641.

Mohd., Sofian (2006) Dynamic analysis of a 10m diameter wind turbine rotor under maximum wind load of Malaysia. Masters thesis, Universiti Teknologi Malaysia.

Mohamed Rehan, Muhammad Saifuddin (2006) Dynamic analysis of tramcar suspension system. Masters thesis, Universiti Teknologi Malaysia.

Lau, Chin Wei (2006) Modeling of dynamic behavior of printed circuit board (PCB) subjected to mechanical shock loading. Masters thesis, Universiti Teknologi Malaysia.

Abd. Aziz, Mohamad Redhwan (2006) Natural convection in semi trapezoidal enclosure. Masters thesis, Universiti Teknologi Malaysia.

Mohamed Ishak, Saiddi Ali Firdaus (2006) Natural convection in semi-cylindrical cavity with heat flux boundary conditions into the system. Masters thesis, Universiti Teknologi Malaysia.

Tang, Yu Cai (2006) Performance evaluation of coated carbide cutting tools when turning hardened tool steel. Masters thesis, Universiti Teknologi Malaysia.

Nasutian, Henry and Wan Hassan, Mat Nawi (2006) Potential electricity savings by variable speed control of compressor for air conditioning systems. Clean Technologies and Environmental Policy, 8 (2). pp. 105-111. ISSN 1618-954X

Nasution, Henry and Wan Hassan, Mat Nawi (2006) Potential electricity savings by variable speed control of compressor for air conditioning systems. Clean Technologies and Environmental Policy, 8 (2). pp. 105-111. ISSN 1618-954X (Print) 1618-9558 (Online)

Jamaludin, Khairur Rijal and Muhamad, Norhamidi and M. Amin, Sri Yulis and Ab. Rahman, Mohd Nizam and Ibrahim, Murtadhahadi (2006) Rheological Investigation Of Stainless Steel Powder In Bimodal Particle Size Distribution. Journal of Applied Technology, 4 (1). pp. 51-59. ISSN 1693-2536

Ab Ghani, Mohd. Satar (2006) Simulation and experimental analysis of a suspension system. Masters thesis, Universiti Teknologi Malaysia.

Osman Ali, Hassan (2006) Stress analysis and fatigue life prediction of a wobble-plate. Masters thesis, Universiti Teknologi Malaysia.

Wong, King Jye (2006) Stress analysis of femur and femoral stems for hip arthroplasty. Masters thesis, Universiti Teknologi Malaysia.

Ngadimon, Khairulnizam (2006) Design and simulation of hydraulic shaking table. Masters thesis, Universiti Teknologi Malaysia.

Lim, Chun Khai (2006) A design of precision linear z-transverse antenna positioner. Masters thesis, Universiti Teknologi Malaysia.

Ng, Tee Neng (2006) Design and optimization of the scavenging system of a multi-cylinder two-stroke scotch-yoke engine. Masters thesis, Universiti Teknologi Malaysia.

Vichare, Parag Shashikant (2006) Performance evaluation of grinding and lapping operations for generating aspheric surfaces on glass moulds using vertical machining centre. Masters thesis, Universiti Teknologi Malaysia.

Wong, Kwon Cheong (2006) Preparation and characterization of carbon molecular sieve produced from palm shell. Masters thesis, Universiti Teknologi Malaysia.

Mohd Ghazali, Normah and Abd Aziz, Azhar and Rajoo, Srithar and Che Sidek, Aswadi (2006) Environmentally Friendly Refrigeration With Thermoacoustic. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Setyawan, Dony (2006) Damage stability of small vessel. Masters thesis, Universiti Teknologi Malaysia.

Yaakob, Omar and Abdul Malik, Adi Maimun and Samian, Yahya and Fitriadhy, Ahmad (2006) Development Of A Semi-Swath Craft For Malaysian Waters. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Pitowarno, Endra (2006) Intelligent active force control for mobile manipulator. PhD thesis, Universiti Teknologi Malaysia.

Fong, Yeow Huang (2006) Load dispatch optimization of open cycle industrial gas turbine plant incorporating operational, maintenance and environmental parameters. Masters thesis, Universiti Teknologi Malaysia.

Tan, Meng Loon (2006) Pembangunan sistem nyah cemar kimia anggota untuk tentera darat Malaysia. Masters thesis, Universiti Teknologi Malaysia.

Ling, Tuong Thai (2006) The effects of bismuth, strontium and antimony additions on the microstructure and mechanical properties of A356 aluminium casting alloy. Masters thesis, Universiti Teknologi Malaysia.

Mahmoud, Abdelgadir Mohamed (2006) Experimental Study On The Response Of Mistuned Bladed Disk. PhD thesis, Universiti Teknologi Malaysia .

Hussain, Ahmad (2006) Hydrodynamic And Thermochemical Studies Of Palm Shell Waste And Coal Blends In A Circulating Fluidised Bed Riser. PhD thesis, Universiti Teknologi Malaysia .

Hamzah, Esah and Purniawan, Agung and Mohd. Toff, Mohd. Radzi (2006) A review on the morphology of daimond thin film coating on various types of substrate materials. Jurnal Mekanikal (21). pp. 16-26. ISSN 0127-3396

Abd. Mukti, Mohd. Afifi and Tawi, Kamarul Baharin and Yaakob, Omar and Nasirudin, Ahmad and Abd. Ghani, Mohd. Pauzi and Mat Lazim, Tholudin (2006) An environmental friendly leisure boat. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Abu Bakar, Abd. Rahim and Ouyang, Huajiang (2006) Complex eugenvalue analysis and dynamic transient analysis in predicting disc brake squeal. International Journal Vehicle Noise & Vibration, 2 (2). p. 143. ISSN 1479-1471

Wan Ali, Wan Khairuddin and Lim, Chun Kai (2006) Development of antenna positioner. Jurnal Mekanikal (21). pp. 53-64. ISSN 0127-3396

Mohd. Noor, Hamzah and Maimun, Adi and Abd. Wahab, Ahmad Khairi and Ismail, Hadibah and Priyanto, Agoes and Muhammad, A. Haris (2006) Effects of coastal development on ship manoeuvring and navigation. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Mat Saman, Muhamad Zameri and Blount, Gordon N. (2006) End of life vehicles recovery : process descriptio, its impact and direction of research. Jurnal Mekanikal (21). pp. 40-52. ISSN 0127-3396

Maimun, Adi and Yaakob, Omar and Kamal, Md. Ahm and Ng, Chee Wei (2006) Evaluation of seakeeping analysis of a fishing vessel using a wave buoy and onboard motions monitoring device. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Ani, Farid Nasir and Hussain, Ahmad and Darus, Amer Nordin (2006) Gas-solid flow modelling in the riser of a circulating fluidised bed. International Journal of Modelling and Simulation . ISSN 0228-6203

Ani, Farid Nasir and Hussain, Ahmad and Darus, Amer Nordin and Jack, Ray Morhhy (2006) Hydrodynamic and fluidization behaviour in a circulating fluidized bed. International Journal of Mechanical & Materials Engineering (IJMME), 1 (1). pp. 17-22. ISSN 1544-4740

Ismail, R. and Ismail, A. Y. and Mat Darus , I. Z. (2006) Identification algorithms of flexible structure using neural networks. In: Scored 2006 - Proceedings of 2006 4th Student Conference on Research and Development "Towards Enhancing Research Excellence in the Region", Malaysia.

Mubarak, A. and Hamzah, E. and M. Toff, M. R. (2006) Influence of Nitrogen Gas Flow Rate on the Microstructural and Mechanical Properties of Tin Deposited Carbon Steel Synthesized by CAE PVD Technique. ASEAN Journal on Science and Technology for Development, 23 (4). pp. 239-251. ISSN 0217-5460

Abd. Rahim, Erween and Sharif, Safian (2006) Investigation of tool life and surface integrity when drilling Ti-6A1-4V and Ti-5A1-4V-Mo/Fe. JSME International Journal, Series C: Mechanical Systems, Machine Elements and Manufacturing , 49 (2). pp. 340-345. ISSN 1347-538X

Abd. Rahim, Erween and Sharif, Safian (2006) Investigation on Tool Life and Surface Integrity when Drilling Ti-6Al-4V and Ti-5Al-4V-Mo/Fe. JSME International Journal Series C, 49 (2). pp. 340-345. ISSN 1344-7653

Mohd. Jaafar, Mohammad Nazri (2006) Jadual Dinamik Gas. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0395-4

Mohd. Yusof, Sha'ri and Chin, Wen Kheong (2006) Line balancing improvement in the welding section of a car assembling plant. Jurnal Teknologi A (44(A)). pp. 81-96. ISSN 0127-9696

Hanafiah, Khairul Anwar (2006) Lukisan Kejuruteraan Berbantu Komputer Edisi Kedua. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0403-9

Tang, Howe Hing and Mailah, Musa (2006) Motion Control of Nonholonomic Wheeled Mobile Robot in a Structured Layout. Jurnal Mekanikal (21). pp. 27-39. ISSN 0127-3396

Abdul Rahim, Abd. Rahman (2006) New Product Development Framework For Engineer-Toorder Production. PhD thesis, Universiti Teknologi Malaysia.

AbuBakar, A. R. and AbdulHamid, M. K. and Mohamad, M. and Dzakaria, A. and AbdGhani, B. (2006) Numerical analysis of disc brake squeal considering temperature dependent friction coefficient. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Mohamed Rehan, Muhammad Saifuddin and Yusof, Mustafa and Abd. Rahman, Roslan (2006) Parametric studies on tramcar suspension system. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Mohd. Samin, Pakharuddin and Tang, Siew Eng and Hudha, Khisbullah (2006) Passenger car handling model validation using LMS-DADS. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Arafat, Andril and Ahmad, Zair Asrar and Syahrom, Ardiyansyah and Mohd Ainon, Nor Ilham and Musa, Md. Nor and Abdul-Latif, Ainullotfi and Wan Mat, Wan Ali (2006) Piston ring assembly for a new natural gas vehicle symmetrical multistage wobble-plate compressor. In: Proceedings of the 1st Regional Conference On Vehicle Engineering and Technology 2006 (RIVET 2006), 3-5 July 2006, Kuala Lumpur, Malaysia. (Unpublished)

Mohd Taib, Jamalludin and Hanafiah , Khairul Anwar and Daud, Mohd Fadzil (2006) Reka Bentuk Berbantu Komputer: Asas Pemodelan. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0408-X

Abdul Aziz, Azhar and A. Latiff, Z. and M. Ali, M. F. and M. Said , M. F. (2006) Retrofitting of auxiliary components to enhance the performance of a single-cylinder, air-cooled gasoline two-stroke engine. Jurnal Mekanikal (22). pp. 53-63. ISSN 0127-3396

Latiff, Z. A. and Prabakaran, V. and Aziz, A. A. (2006) Sampling of unregulated components of a two-stroke, stepped-piston engine emission. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Ayob, Amran (2006) Stress analysis of torispherical shell with radial nozzle. IEM Journal The Journal of the Institution of Engineers, Malaysia , 67 (3). p. 59. ISSN 0126-513X

Abd. Kader, Ab. Saman and Suleiman, Oladokun (2006) Sustainable periodic navigation channel assessment initiative for restricted inland waterway. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Abdul Aziz, Azhar and Said, Mohd Farid and Awang, Mohamad Afiq and Said, Mazlan (2006) The effects of neutralized palm oil methyl esters (NPOME) on performance and emission of a direct injection diesel engine. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Yaakob, Omar and Abd. Ghani, Pauzi and Abd. Mukti, Mohd. Afifi and Nasirudin, Ahmad and Tawi, Kamarul Baharin and Mat Lazim, Tholudin (2006) The wake wash prediction on an asymmetric catamaran hull form. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Ani, Farid Nasir and Darus, Amer Nordin and Mustafa, Azeman and Hussain, Ahmad and Mokhtar, Hamdan and Azam, Saiful (2006) Themochemical behaviour of empty fruit bunches and oil palm shell waste in a circulating fluidized-bed combustor (CFBC). Journal of Oil Palm Research, 18 . pp. 210-218. ISSN 1511-2780

Ani, Farid Nasir and Darus, Amer Nordin and Hussain, Ahmad and Mokhtar, Hamdan and Azam, Saiful (2006) Thermogravimetric and kinetic studies on palm shells. Journal of Industrial Technology, 15 (1). pp. 87-99. ISSN 0128-4940

Hussain, Ahmad and Ani, Farid Nasir and Darus, Amer Nordin and Ahmed, Zainal (2006) Thermogravimetric and thermochemical studies of malaysian oil palm shell waste. Jurnal Teknologi . pp. 43-53.

Abd. Kader, Ab. Saman and Ahmad, Mohd. Zamani (2006) Utilisation of inland water transport system in South East Asian region - an overview of the prospect. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Abd. Kader, Ab. Saman and Idris, Jamaliah and Abdul Mukti, Mohd. Afifi and Ahmad, Mohd. Zamani (2006) Vehicle equipment selection model for preliminary design using fuzzy multi-criteria decision making method. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Mohamad, Maziah and Mailah, Musa and Muhaimin, Abdul Halim (2006) Vibration control of mechanical suspension system using active force control. In: Proceedings the 1st International Conference on Natural Resources Engineering and Technology INRET2006, 24-25 July 2006, Marriot, Putrajaya, Malaysia. (Unpublished)

Abu Bakar, A R. and Li, L and James, S and Ouyang, H and Siegel, J E (2006) Wear simulation and its effect on contact pressure distribution and squeal of a disc brake. Proceedings of the International Conference on Vehicle Braking Technology . pp. 233-242. ISSN 0 85316 245X

Abdul Ghani, Mohamad Pauzi and Ahmad Sabki, Ahmad Fuaad (2005) Investigation Of Wake Wash In The Towing Tank. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Wan Hamid, Wan Harun and Mohd Rohani, Jafri (2005) The Study On The Integration Of Activity Based Costing (ABC) System And Six-Sigma Principle. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Ani, Farid Nasir and Badawi, E.M and Kannan, K.S (2005) The Effect of Absorber Packing Height on the Performance of a Hybrid Liquid Desiccant System. Renewable Energy, 30 (15). pp. 2247-2256. ISSN 09601481

Tan, Chun Chai (2005) A numerical analysis of fixed offshore structure subjected to environmental loading in Malaysian water. Masters thesis, Universiti Teknologi Malaysia.

Chin, Doris Chong Leng (2005) A reliability analysis of a Malaysia jacket platform. Masters thesis, Universiti Teknologi Malaysia.

A. Khan, Zahid and Kamaruddin, S. and Quadir, G. A. and Suhail, A. and Seetharamu, K. N. (2005) Application of artificial neural network (AAN) for prediction of sensible and latent heat losses from a cow. Jurnal Mekanikal (20). ISSN 0127-3396

Yaacob, Mohd Shafiek and Jamaluddin, Hishamuddin and Harun, Sobri (2005) Daily streamflow forecasting using simplified rule-based fuzzy logic system. Journal The Institution of Engineers Malaysia, 66 (4). pp. 23-28. ISSN 0126-513X

Tan, C. F. and Ismail, N. and Wong, S. V. and Sulaiman, S. and Osman, M. R. (2005) Development Of Step Hole Recognition System For Computer Aided Process Planning. Jurnal Teknologi (A), 43 (A). pp. 73-86. ISSN 0127-9696

Abdelraheem Elhaj, Hazir Farouk (2005) Effect of adopting different dispatching rules on the mean flow time in a two machine batch-shop problem. Masters thesis, Universiti Teknologi Malaysia.

Surjosatyo, Adi and Ani, Farid Nasir (2005) Experimental and prediction of the development of low-calorific swirl burner. International Energy Journal, 6 (2 ). ISSN 1513-718X

Surjosatyo, A. and Ani, F. N. (2005) Experimental and prediction of the development of low-calorific swirl burner. Experimental and prediction of the development of low-calorific swirl burner, 6 (2).

Salehun, Md Amirul Khair and Md. Tap, Masine and Mohamed Shaharoun, Awaluddin (2005) Guideline for improving capacity of a job shop based on selected performance measures. Jurnal Teknologi A, 43 . pp. 87-104. ISSN 0127-9696

Salehun, Md Amirul Khair and Md Tap , Masine and Mohamed Shahroun, Awaluddin (2005) Guideline For Improving Capacity Of A Job Shop Based On Selected Performance Measures. Jurnal Teknologi (A), 43 (A). pp. 87-104. ISSN 0127-9696

Mohd. Jaafar, Mohammad Nazri and Samat, Ismail and Abdul Mookmin, Muhamed Shukri (2005) Kajian perbandingan ram lengkung dan ram rata bagi pemusar udara aliran jejarian dalam mengurangkan emisi. Journal - The Institution of Engineers, Malaysia, 66 (4). pp. 57-63. ISSN 0126-513X

Hamzah, Esah and Kanniah, Maiiyeaalagan and Harun, Mohd (2005) Microstructural Characterisation Of As-Cast Binary Near Gamma Titanium Aluminides. Jurnal Teknologi (A) , 43 (A). pp. 113-124. ISSN 0127-9696

Hamzah, Esah and Kanniah, Maiiyeaalagan and Harun, Mohd (2005) Microstructural Characterisation of As–Cast Binary Near Gamma Titanium Aluminides. Jurnal Teknologi A, 43 . pp. 113-124. ISSN 0127-9696

Wijaya, Moh. Lutfi (2005) Modelling and control of an intelligent antilock braking system. Masters thesis, Universiti Teknologi Malaysia.

Gopal , Sekharan and Mohd Rohani, Jafri and Mohd Yusof, Sha’ri and Abu Bakar, Zailis (2005) Optimization Of Solder Paste Printing Parameters Using Design Of Experiments (Doe). Jurnal Teknologi (A) , 43 (A). pp. 11-20. ISSN 0127-9696

Sekharan, Gopal and Mohd Rohani, Jafri and Mohd Yusof, Sha’ri (2005) Optimization Of Solder Paste Printing Parameters Using Design Of Experiments (DOE). Jurnal Teknologi A, 43 (A). pp. 11-20. ISSN 0127-9696

Abu Bakar, Abd Rahim and Huajiang, Ouyang (2005) Prediction Of Disc Brake Contact Pressure Distributions By Finite Element Analysis. Jurnal Teknologi (A), 35 (A). pp. 21-36. ISSN 0127-9696

Abu Bakar, Abd Rahim and Ouyang, Huajiang (2005) Prediction of disc brake contact pressure distributions by finite element analysis. Jurnal Teknologi A, 43 . pp. 21-36. ISSN 0127-9696

Mubarak, A. and Hamzah, Esah and Toff, M. R. M. (2005) Review of physical vapour deposition (PVD) techniques for hard coating. Jurnal Mekanikal (20). pp. 42-51. ISSN 0127-3396

Cheng, Eng Cong and Velautham, Sanjayan and Darus, Amer Nordin (2005) Solar thermal organic Rankine cycle as a renewable energy option. Jurnal Mekanikal (20). pp. 68-77. ISSN 0127-3396

Zaman@Bujang, Izzuddin (2005) Study of dynamic behaviour of truck chassis. Masters thesis, Universiti Teknologi Malaysia.

Ani, Farid Nasir and Badawi, E. M. and Kannan, K. S. (2005) The effect of absorber packing height on the performance of a hybrid liquid desiccant system. An International Journal Renewable Energy, 30 (15). pp. 2247-2256. ISSN 0960-1481

Ani, F. N. and Badawi, E. M. and Kannan, K. S. (2005) The effect of absorber packing height on the performance of a hybrid liquid desiccant system. The effect of absorber packing height on the performance of a hybrid liquid desiccant system, 30 . pp. 2274-2256.

F. A. , Ani and E. M. , Badawi and K. S. , Kanan (2005) The effect of absorber packing height on the performance of a hybrid liquid desiccant system. Renewable Energy, 30 . pp. 2247-2256.

F. A. , Ani and E. M. , Badawi and K. S. , Kanan (2005) The effect of absorber packing height on the performance of a hybrid liquid desiccant system. Renewable Energy, 30 . pp. 2247-2256.

Wan Nik, W. B. and Ani, Farid Nasir and Masjuki, H. H. and Eng Giap, S. G. (2005) Rheology of bio-edible oils according to several rheological models and its potential as hydraulic fluid. Industrial Crops and Products, 22 (3). pp. 249-255. ISSN 0926-6690

Wan Nik, W. B. and Ani, F. N. and Masjuki, H. H. and Eng Giap, S. G. (2005) Rheology of bio-edible oils according to several rheological models and its potential as hydraulic fluid. Industrial Crops and Products, 22 . pp. 249-255. ISSN 0926-6690

Wong, Kuan Yew (2005) The Potential Roles of Engineers in Knowledge Management: An Overview. Jurutera, November . pp. 26-29. ISSN 0126-9909

Ramasamy, Devarajan (2005) Development of a compressed natural gas (CNG) mixer for a two stroke internal combustion engine. Masters thesis, Universiti Teknologi Malaysia.

Mohd. Jaafar, Mohammad Nazri and Abdul Wahid, Mazlan and Mustafa, Azeman and Ishak, Mohamad Shaiful Ashrul (2005) Combustion Characteristic Of Air Staging In Gas Burner System. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Mohd. Jaafar, Mohammad Nazri and Sulian, Mohd Sharul (2005) Keberkesanan pembakaran udara berperingkat dalam mengurangkan emisi dari pembakar berbahanapi gas. The Journal Of The Institution Of Engineers, Malaysia, 66 (3). pp. 33-37. ISSN 0126-513X

Rashid, Roslina and Jamaluddin, Hishamuddin and Saidina Amin, Nor Aishah (2005) Parameter estimation of tapioca starch hydrolysis process: application of least squares and genetic algorithm. Journal The Institution of Engineers Malaysia, 66 (3). pp. 51-60. ISSN 0126-513X

Abd. Rahim, Erween (2005) Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy. Masters thesis, Universiti Teknologi Malaysia.

Venkatesh, V. C. and Izman, S. and Vichare, P. S. and Mon, T. T. and Murugan, S. (2005) The novel bondless wheel, spherical glass chips and a new method of aspheric generation. Journal of Materials Processing Technology, 167 (2-3). pp. 184-190. ISSN 09240136

V. C., Venkatesh and S., Izman and Vichare, P. S. and Mon, T. T. and S., Murugan (2005) The novel bondless wheel, spherical glass chips and a new method of aspheric generation. Journal of Materials Processing Technology, 167 . pp. 184-190. ISSN 0924-0136

Rival, Rival (2005) Electrical discharge machining of titanium alloy using copper tungsten electrode with SiC powder suspension dielectric fluid. Masters thesis, Universiti Teknologi Malaysia.

Ishak, Mohamad Shaiful Ashrul (2005) Pembangunan pembakar berbahan api cecair dengan ciri-ciri rendah NOx. Masters thesis, Universiti Teknologi Malaysia.

Mubarak, Ali and Hamzah, Esah and Mohd Toff, Mohd Radzi and Hashim, Abdul Hakim (2005) The Effect Of Nitrogen Gas Flow Rate On The Properties Of Tin-Coated High-Speed Steel (Hss) Using Cathodic Arc Evaporation Physical Vapor Deposition (Pvd) Technique. Surface Review and Letters, 12 (4). pp. 631-643. ISSN 0218-625X

Nik, W.B.W and Ani, F. N. and Masjuki, H.H (2005) Thermal stability evaluation of palm oil as energy transport media. Energy conversion and management, 46 (13-14). pp. 2198-2215. ISSN 0196-8904

Ani, Farid Nasir (2005) Performance Investigation Of Energy Transport Media As Influenced By Crop Based Properties. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Abdul Aziz, Azhar and Suhadi, Mohd. Sairaji and Mohd Noor, Alias and Abdullah, Abu Hassan and Tawi, Kamarul Baharin and Abu Bakar, Rosli (2005) The Design And Development Of A New Twostroke (125 Cc) Stratified-Charge, Lean-Burn Air-Cooled Engine. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Abd. Rahman, Roslan and Kamsah, Nazri and Abd. Latif, Zulkarnain (2005) Utilisation Of Noise Suppression Techniques In The Development Of Two-Stroke, Stratified-Charge, Lean-Burn Gasoline Engines. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Hussain, Ahmed and Ani, Farid Nasir and Darus, Amer Nordin (2005) CFD Flow Modeling of Riser Exit Geometries of a Circulating Fluidized Bed. Mehran University Research Journal of Engineering & Technology, 24 (3). ISSN 0254-7821

Ng, Chee Weng (2005) Mechanism-based reliability model for electronic packages. Masters thesis, Universiti Teknologi Malaysia.

Abdullah, Haryati and Ani, Farid Nasir and Mohd. Jaafar, Mohammad Nazri (2005) Combustion characteristics study of biomass in a fluidized bed combustor. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Abul Hossain, Khandoker and Mohd Jaafar, Mohammad Nazri and Mustafa, Azeman and Ani, Farid Nasir (2005) Application Of Commercial Grade Ammonia Liquor In The Selective Non-Catalytic Reduction Of NOx In Combusted Gas From A Diesel Burner. Jurnal Teknologi A, 42 (A). pp. 107-118. ISSN 0127-9696

Abul Hossain, Khandoker and Mohd. Jaafar, Mohammad Nazri and Mustafa, Azeman and Ani, Farid Nasir (2005) Application of commercial grade ammonia liquor in the selective non–catalytic reduction of nox in combusted gas from a diesel burner. Jurnal Teknologi A, 42 . pp. 107-118. ISSN 0127-9696

Sulaiman, Suditama and Megat Ahmad, Megat Mohamad Hamdan and Sulaiman, Shamsuddin and Adam, Normariah (2005) Heat transfer study in the low temperature thermal energy storage material (multi-component material) between tubes array during melting. Jurnal Mekanikal (19). pp. 71-83. ISSN 0127-3396

Suroso, Arief (2005) Hydraulic model test of wave energy conversion. Jurnal Mekanikal (19). pp. 84-94. ISSN 0127-3396

Mat Sarip, Abdul Rahim (2005) Kajian secara teori dan ujikaji terhadap pemampat ram gelangsar berputar. Masters thesis, Universiti Teknologi Malaysia.

Samat, Ismail and Mohd Jaafar, Mohammad Nazri (2005) Kelebihan Pemusar Udara Ram Lengkung Berbanding Ram Rata Dalam Mengurangkan Emisi. Jurnal Teknologi F, 42 (F). pp. 89-106. ISSN 0127-9696

Samat, Ismail and Mohd. Jaafar, Mohammad Nazri (2005) Kelebihan pemusar udara ram lengkung berbanding ram rata dalam mengurangkan emisi. Jurnal Teknologi F, 42 . pp. 89-106. ISSN 0127-9696

Yusof, Ahmad Anas and Wan Ali, Wan Khairuddin and Abd Rahman, Tharek and Ani, Farid Nasir (2005) Microwave and reflection properties of palm shell carbon–polyester conductive composite absorber. Jurnal Teknologi A, 42 . pp. 59-74. ISSN 0127-9696

Mailah, M. and Pitowarno, E. and Jamaluddin, H. (2005) Robust motion control for mobile manipulator using resolved acceleration and proportional-integral active force control. International Journal of Advanced Robotic Systems , 2 . pp. 125-134. ISSN 1729 - 8806

Choo, Shinn Chei (2005) Technoeconomical analysis of a residential photovoltaic vapour compression air conditioning system. Masters thesis, Universiti Teknologi Malaysia.

Murtedjo, Mas and B. Djatmiko, Eko and Sudjianto, Hendri (2005) The influence of buoyancy parameters on the dynamic behavior of articulated tower. Jurnal Mekanikal (19). pp. 32-47.

Yaakob, Omar and Quah, Peng Chau (2005) Weather Downtime And Its Effect On Fishing Operation In Peninsular Malaysia. Jurnal Teknologi A (42 A). pp. 13-26. ISSN 0127-9696

Yaakob, Omar and Quah, Peng Chau (2005) Weather downtime and its effect on fishing operation in peninsular malaysia. Jurnal Teknologi A, 42 . pp. 13-26. ISSN 0127-9696

Velautham, Sanjayan and Abdul Aziz, Azhar and Mohd Ghazali, Normah (2005) Renewable Energy Powered Organic Ranking Cycle. Project Report. Universiti Teknologi Malaysia, Universiti Teknologi Malaysia. (Unpublished)

Mohd. Jaafar, Mohammad Nazri and Mustafa, Azeman and Musa, Hamidon and Senawi, Yusof and Wan Omar, Wan Zaidi and Abdul Majid, Kamsani and Mohamad Shaiful Ashrul, Ishak (2005) Development of Pollution Control Technique Using Liquid Fuel Burner With Swirling Flow. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Mohd. Jaafar, Mohammad Nazri and Azeman, Mustafa and Hamidon, Musa and Wan Zaidi, Wan Omar and Mohd. Zamri, Yusoff and Kamsani, Abdul Majid and Mohamad Shaiful Ashrul, Ishak (2005) Development of Low Liquid Fuel Burner. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Abu Bakar, A. R. and Ouyang, H. and Titeica, D. and Hamid, M. K. A. (2005) Modelling and Simulation of Disc Brake Contact Analysis and Squeal. Seminar on Advances in Malaysian Noise Vibration and Comfort (NVC 2005) .

Tamin, M N and Liew, Y B (2005) Numerical modeling of cyclic stress-strain behavior Of sn-pb solder joint during thermal fatigue. National Seminar on Computational & Experimental Mechanics (CEM) 2005 . pp. 351-360.

Abu Bakar, A R. and Hamid, M K A and Zakaria, K (2005) Simulasi tekanan sentuhan dinamik bagi brek cakera menggunakan kaedah unsur terhingga.". Proceedings of Computational & Experimental Mechanics . pp. 287-296.

Suardi, Khairmen (2005) The effect of heat treatment and chromium addition on γ-titanium aluminide resistance to hydrogen attack. Masters thesis, Universiti Teknologi Malaysia.

Mohd Noor, Alias and Abu Bakar, Rosli and Abdul Aziz, Azhar and Abdul Latif, Zulkarnain and Mohd Rohani, Jafri and Saat, Aminuddin (2005) Design And Development Of Auxiliary Components For A New Two-Stroke, Stratified-Charge, Lean-Burn Gasoline Engine. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Hamzah, E. and Suardi, K. and Qourdjini, Ali (2005) Effect of Microstructures on the Hydrogen attack to Gamma Titanium Aluminide at Low Temperature. Materials science & engineering. A, Structural materials : properties, microstructure and processing , 397 . pp. 41-49. ISSN 0921-5093

Andalas, Ronny (2005) Application of accuracy control system in Batam shipyard. Masters thesis, Universiti Teknologi Malaysia.

Taib, Mohd. Yusof (2005) Design and development of rotating-sleeve refrigerant compressor. Masters thesis, Universiti Teknologi Malaysia.

Zadry, Hilma Raimona (2005) The integration of Total Quality Management (TQM) and Theory Of Constraints (TOC) implementation in Malaysian automotive suppliers. Masters thesis, Universiti Teknologi Malaysia.

Hassan, Adnan and Mohd Shaharoun, Awaluddin and Oktaviandri, Muchamad (2005) Dynamic Scheduling In A Multi-Product Manufacturing System. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Hossain, K.A and Mohd Jaafar, M. N. and Appalanide, K.B and Mustafa, A. and Ani, F.N. (2005) Application of Urea Based SNCR System in The Combustion Effluent Containing Low Level Of Baseline Nitric Oxide. Enviromental Technology Selper Ltd, 26 (3). pp. 251-260. ISSN 0959-3330

Abdul Aziz, Azhar and Lim, Chon Wei (2005) Development And Performance Evaluation Of A Prototype Electric Hybrid Powertrain System For Automotive Applications. Journal The Institution of Engineers Malaysia, 66 (1). pp. 73-80. ISSN 0126-513X

Appalanidu, Kiran Babu (2005) Development of low emission oil burner. Masters thesis, Universiti Teknologi Malaysia.

Mat Darus, I.Z and Tokhi, M O (2005) Soft computing-based active vibration control of a flexible structure. Engineering Applications of Artificial Intelligence, 18 (1). pp. 93-114. ISSN 0952-1976

Mailah, Musa and Jamaluddin, Hishamuddin and Pitowarno, Endra and Purnomo, Didik Setyo (2005) Intelligent Material Handling Mobile Robot for Industrial Purpose with Active Force Control Capability. Project Report. Universiti Teknologi Malaysia, Universiti Teknologi Malaysia. (Unpublished)

Wan Ali, Wan Khairuddin and Abd Rahman, Tharek (2005) Wideband Microstrip Antenna For Land Based Vehicles. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Hamdy Abd El Rahman, Gouda Mahfouz (2005) Analytical And Experimental Analysis On Scroll Compressor For Automobile Air Conditioning System. PhD thesis, Universiti Teknologi Malaysia .

Amrin, Astuty (2005) High-Temperature Oxidation Of Titanium Aluminides. PhD thesis, Universiti Teknologi Malaysia .

Bambang , Pramudono (2005) Study On Emulsion Stability And Chemical Demulsification Characteristics Of Crude Oil Emulsion. PhD thesis, Universiti Teknologi Malaysia .

Wan Nik, Wan Mohd Norsani (2005) Thermal And Rheological Properties Of Palm Based Oil As Hydraulic Fluid. PhD thesis, Universiti Teknologi Malaysia .

Wong, Kuan Yew (2005) A critical review of knowledge management frameworks. International Journal of Information Technology and Management , 4 (3). pp. 269-289. ISSN 1461-4111

Wong, Kuan Yew and Aspinwall, Elaine (2005) An empirical study of the important factors for knowledge-management adoption in the SME sector. Journal of Knowledge Management, 9 (3). pp. 64-82. ISSN 1367-3270

Alias, Amran and Mat Rejab, Mohd. Ruzaimi and Mohamad, Mohd. Radzai and Md. Akil, Hazizan and Ahmad Nor, Nor Azlan (2005) Behaviour of circular sandwich panel under dynamic loading. Jurnal Mekanikal (20). pp. 96-111. ISSN 0127-3396

Hamzah, Esah and Kanniah, Maiiyeaalagan (2005) Corrosion Behavior of low carbon steel sheets for car bodies. Jurnal Mekanikal, June (19). pp. 57-70.

Wong, Kuan Yew (2005) Critical success factors for implementing knowledge management in small and medium enterprises. Industrial Management & Data Systems, 105 (3). pp. 261-279. ISSN 0263-5577

Meng, Hee Lim and Leong, Salman (2005) Diagnosis for loose blades in gas turbines using wavelet analysis. Journal of Engineering for Gas Turbine and Power, 127 (2). pp. 314-322. ISSN 0742-4795

Hudha, K and Jamaluddin, Hishamuddin and Samin, P. M. and Rahman, R.A (2005) Effects of control techniques and damper constraint on the performance of a semi-active magnetorheological damper. International Journal Vechicle Aotunomous Systems, 3 (2-4). pp. 230-252. ISSN 1471-0226

K. , Hudha and Jamaluddin, H. and Samin, P. M. and Rahman, R. A. (2005) Effects of control techniques and damper constraint on the performance of a semi-active magnetorheological damper. International Journal of Vehicle Autonomous Systems, 3 (2 - 4). pp. 230-252. ISSN 1471-0226

Toh, C. L. and Idris, Nik Rumzi and Yatim, Abdul Halim and Muhammad, N. D. and Elbuluk, M. E. (2005) Implementation of a New Torque and Flux Controllers for Direct Torque Control (DTC) of Induction Machine Utilizing Digital Signal Processor (DSP) and Field Programmable Gate Arrays (FPGA). The 36th IEEE Conference on Power Electronics Specialists . pp. 1594-1599.

Lim, Boon Han and Mailah, Musa (2005) Intelligent biometric signature verification system incorporating neural network. Jurnal Mekanikal (20). pp. 22-41. ISSN 0127-3396

Mohd. Jaafar, Mohammad Nazri (2005) Jenis Enjin Pesawat Udara dan Analisis Kitar. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0376-8

Wong, Kuan Yew and Aspinwall, Elaine (2005) Knowledge Management : Case Studies in SMEs and Evaluation of an Integrated Approach. Journal of Information and Knowledge Management, 4 (2). pp. 95-111.

Wong, K. Y. and Aspinwall, E. (2005) Knowledge Management: Case Studies in SMEs and Evaluation of an Integrated Approach. Journal of Information and Knowledge Management, 4 (2). pp. 95-111.

K. , Hudha and H. , Jamaluddin and P. M. , Samin and R. A. , Rahman (2005) Non-parametric linearised data driven modelling and force tracking control of a magnetorheological damper. International Journal of Vehicle Autonomous Systems , 3 (2, 3, 4). pp. 230-252.

Daud, Mohd Fadzil and Hanafiah, Khairul Anwar (2005) Panduan Asas Lukisan Kejuruteraan Edisi Kedua. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0381-4

Mailah, Musa and Pitowarno, Endra and Jamaluddin, Hishamuddin (2005) Robust Motion Control for Mobile Manipulator Using Resolved Acceleration and Proportional-Integral Active Force Control. International Journal of Advanced Robotic System, 2 (2). pp. 125-134. ISSN 1729-8806

Hussain, A. and Ani, F. N. and Darus, A. N. and Mustafa, A. and Salema, A. A. (2005) Simulation studies of gas-solid in the riser of a Circulating Fluidized Bed. In: Proceedings of the 18th International Conference on Fluidized Bed Combustion.

Tamin, M. N. and Liew, Y. B. and Wagiman, A. N. R. and Loh, Y. K. (2005) Solder joint fatigue in a surface-mount assembly subjected to mechanical loading. In: Proceedings of 7th Electronics Packaging Technology Conference, EPTC 2005 .

Ariffin, Mohd Kamal (2005) Termodinamik Asas. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0392-X

Wan Nik, W. B. and Ani, F. N. and Masjuki, H. H. (2005) Thermal stability evaluation of palm oil. Energy Conversion and Management, 46 . pp. 21198-2215.

Mohd. Jaafar, Mohammad Nazri and Mustafa, Azeman and Musa, Hamidon and Senawi, Yusof and Wan Omar, Zaidi and Abdul Majid, Kamsani (2004) Development Of Pollution Control Technique Using Liquid Fuel Burner With Swirling Flow. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Ab. Wahab, Abas (2004) Establishing The Wind Map For Sabah and Sarawak, Malaysia. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Kamsah, Nazri and Idris, Mohd. Hasbullah and Phuan , Yoong Jiann (2004) Fe Evaluation Of Thermal Property Of Mould Wall Material For Investment Casting And The Effect Of Layers On The Hardness Of The Casting Product. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Abul Hossain, Khandoker and Mohd. Jaafar, Mohammad Nazri and Mustafa, Azeman and Appalanidu, Kiran Babu and Ani, Farid Nasir (2004) Application of selective non-catalytic reduction of NOx in small-scale combustion systems. Armospheric Environment, 38 (39). pp. 6823-6828. ISSN 1352-2310

Abul Hossain, Khandoker and Mohd Jaafar, Mohammad Nazri and Mustafa, Azeman and Appalanidu, Kiran Babu and Ani, Farid Nasir (2004) Application of selective non-catalytic reduction of NOx in small-scale combustion systems. Atmospheric Environment, 38 . pp. 6823-6828.

Mohd. Jaafar, Mohammad Nazri and Wan Ali, Wan Khairuddin and Dahalan, Md. Nizam (2004) Development of solid rocket propulsion system at UTM. Jurnal Mekanikal, 18 . pp. 111-121. ISSN 0127-3396

Md. Zain, Mohd. Zarhamdy and Tokhi, M. O. and Mailah, Musa and Mohamed, Z. (2004) Improving perfomance in single-link flexible manipulator using hybrid learning control. Jurnal Mekanikal (18). pp. 13-28. ISSN 0127-3396

Md Zain, Mohd Zarhamdy and Tokhi, M. O. and Musa, Mailah and Mohamed, Zaharuddin (2004) Improving performance in single-link flexible manipulator using hybrid learning control. Jurnal Mekanikal (18). pp. 13-28. ISSN 0127-3396

Awang, Dzulkifli (2004) Rekabentuk Industri Dalam Kejuruteraan Mekanikal. In: Conference On Engineering Education (CEE 2004), 14-15 December 2004, Kuala Lumpur.

Yaakob, Omar and Shamsuddin, Suhaili and Koh, Kho King (2004) Stern Flap For Resistance Reduction Of Planing Hull Craft: A Case Study With A Fast Crew Boat Model. Jurnal Teknologi A, 41 (A). pp. 43-52. ISSN 0127-9696

Yaakob, Omar and Shamsuddin, Suhaili and King, Koh Kho (2004) Stern Flap for resistance reduction of planing hull craft: a case study with a fast crew boat model. Jurnal Teknologi A, 41 . pp. 43-52. ISSN 0127-9696

Ayob, Amran (2004) The effect of D/T on the load interaction behavior of a plain pipe. Journal of Pressure Vessel Technology , 126 . pp. 518-523.

Md. Naiem, Mohd. Azzeri (2004) Viability study on the application of advance blasting method in Malaysian shipbuilding industry. Masters thesis, Universiti Teknologi Malaysia.

Ali Sera, Mardani (2004) Development of intake system for improvement of performance of compressed natural gas spark ignition engine. PhD thesis, Universiti Teknologi Malaysia.

Ahmad, Rozie Nani (2004) Development of spreadsheet analysis (SAS) for DFA house methodology. Masters thesis, Universiti Teknologi Malaysia.

Yusof, Ahmad Anas (2004) The development of microwave absorber from oil palm shell carbon. Masters thesis, Universiti Teknologi Malaysia.

Abdul Aziz, Azhar (2004) Cadangan Bagi Membangunkan Sistem Pengangkutan Ringan Halaju Rendah Jenis "ARTICULATING" Bagi Kegunaan Membawa Pelawat di UTM. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Zain, M Z M and Tokhi, M O and Mohamed, Z (2004) Hybrid learning control with input shaping for input tracking and vibration suppression of a flexible manipulator. 7th Biennial ASME Conference Engineering Systems Design and Analysis .

Tang, Howe Hing (2004) Implementation of motion planning and active force control to a virtual wheeled mobile robot. Masters thesis, Universiti Teknologi Malaysia.

Mohd. Jaafar, Mohammad Nazri and Mustafa, Azeman and Musa, Hamidon and Wan Omar, Wan Zaidi and Yusoff, Mohd. Zamri and Abdul Majid, Kamsani (2004) Development Of Low Nox Liquid Fuel Burner. Project Report. Universiti Teknologi Malaysia. (Unpublished)

V. C., Venkatesh and S., Izman and S.C, Mahadevan (2004) Electro-chemical mechanical polishing of copper and chemical mechanical polishing of glass. Journal of Materials Processing Technology, 149 (1-3). pp. 493-498. ISSN 09240136

Aqida, S. N. and Ghazali, M. I. and Hashim, J. (2004) Effects Of Porosity On Mechanical Properties Of Metal Matrix Composite: An Overview. Jurnal Teknologi A, 40 (A). pp. 17-32. ISSN 0127-9696

Abdullah, Ahmad Baharuddin and Razali, Norhamimi and Mohd. Ripin, Zaidi (2004) Kajian kepuasan pelanggan terhadap produk pengguna untuk menyokong seni bina produk modular. Jurnal Mekanikal (17). pp. 1-14. ISSN 0127-3396

Ahmad, Norhayati and Hussin, Munirah (2004) Kesan bahan mangkin ke atas proses pengawetan resin isopoliester dalam penghasilan komposit matrik polimer. Jurnal Mekanikal (17). 15 -35. ISSN 0127-3396

J. R., Ayu Bidiawati and Mohd.Yusof, Sha’ri and Nabi Baksh, Mohamed Shariff (2004) Penjadualan preemption menggunakan aturan pelepasan berprioriti dalam sistem bergangguan. Jurnal Mekanikal (17). pp. 48-55. ISSN 0127-3396

Ismail, Yob Saed and Abu Hassan, Shukur and Abd. Kader, Abd. Saman and Chong, Chin Lee (2004) The mode II interlaminar fracture testing of glass fibre reinforces thermoset composites. Jurnal Mekanikal (17). pp. 87-98. ISSN 0127-3396

Mohd. Ghazali, N. (2004) Thermoacoustic Heat Engine. Jurnal Teknologi A, 40 (A). pp. 67-78. ISSN 0127-9696

Loh, Sheau Ping (2004) Hydrodynamic coefficients of manoeuvring for small vessels. Masters thesis, Universiti Teknologi Malaysia.

Yusof, Mustafa and Abdul Rahman, Roslan (2004) Development Of An Automotive Seat For Ride Comfort. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Kong, Kim Fong (2004) Pengurusan sistem sungai bagi tujuan pengangkutan. Masters thesis, Universiti Teknologi Malaysia.

Yaakob, Mohd. Shafiek (2004) Identification of non-linear dynamic systems using fuzzy system with constrained membership functions. PhD thesis, Universiti Teknologi Malaysia.

Koh, Yee Kan (2004) A unified constitutive model for solder materials. Masters thesis, Universiti Teknologi Malaysia.

R, Ahmad and H. , Jamaluddin and M.A, Hussain (2004) Model structure selection for a discrete-time non-linear system using a genetic algorithm. Journal of Systems and Control Engineering, 218 (12). pp. 85-98. ISSN 0959-6518

Ahmad, R. and Jamaluddin, H. and Hussain, M. A. (2004) Model structure selection for a discrete-time non-linear system using a genetic algorithm. Proceedings of the Institution of Mechanical Engineers. Part I: Journal of Systems and Control Engineering, 218 . pp. 85-98. ISSN 0959-6518

Zain, M Z M and Tokhi, M O and Mohamed, Z and Mailah, M (2004) Hybrid iterative learning control of a flexible manipulator. Proceedings of the 23rd IASTED International Conference Modelling, Identification and Control . pp. 313-318.

Jaan, Soon Tan and Ani, Farid Nasir (2004) Carbon molecular sieves produced from oil palm shell for air separation. Separation Purification Technology, 35 (1). pp. 47-54. ISSN 1383-5866

Tan, J. S. and Ani, F. N. (2004) Carbon molecular sieves produced from oil palm shell for air separation. Separation and Purification Technology, 35 . pp. 47-54. ISSN 1383-5866

Joesni Ralin, Ayu Bidiawati (2004) Penjadualan pengeluaran menggunakan aturan pelepasan berprioriti dalam sistem bergangguan. Masters thesis, Universiti Teknologi Malaysia.

Abul Hossain, Khandoker (2004) Study of urea based selective non-catalytic reduction of NOx in small scale combustion applications. Masters thesis, Universiti Teknologi Malaysia.

Noordin , M. Y. and Venkatesh, V. C. and Sharif, S. and Elting, S. and Abdullah, A. (2004) Application of Response Surface Methodology in Describing the Performance of Coated Carbide Tools when Turning AISI 1045 Steel. Journal of Materials Processing Technology, 145 (1). pp. 46-58. ISSN 09240136

M.Y, Nordin and V. C., Venkatesh and S, Sharif and S, Elting and A, Abdullah (2004) Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel. Journal of Materials Processing Technology, 145 (1). pp. 46-58. ISSN 09240136

Alasso, Ahmed Omar (2004) A Model For Implementation of Preventive Maintenance Management Programs in Construction Project Equipment. Masters thesis, UTM Skudai.

Kang, H. S. and Jalil, M. K. A. and Musa, M. (2004) A PC-based driving simulator using virtual reality technology. Proceedings VRCAI 2004 - ACM SIGGRAPH International Conference on Virtual Reality Continuum and its Applications in Industry . pp. 273-277.

Kang, H.S and Jalil, M.K.A and Mailah, Musa (2004) A PC-based driving simulator using virtual reality technology. In: ProceedingsVRCAI 2004-ACM SIGGRAPH International Conference on Virtual Reality Continuum and its Applications in Industry.

Koh, Yee Kan (2004) A Unified Constitutive Model For Solder Materials. Masters thesis, Universiti Teknologi Malaysia .

Mailah, Musa and Kwek, L. C. and Loo, Chu Kiong (2004) Active Force Control of a 5-link biped robot. In: Proceedings VRCAI 2004-ACM SIGGRAPH International Conference on Virtual Reality Continuum and its Application in Industry, 28-31 Oct. 2002.

Noordin, M.Y. and Venkatesh, V.C. and Sharif, S. and Elting, S. and Abdullah, A. (2004) Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel. Journal of Materials Processing Technology, 145 (1). pp. 46-58.

Ani, Farid Nasir and Abul Hossain, Khandoker and Mohd Jaafar, Mohammad Nazri and Mustafa, Azeman and Appalanidu, Kiran Babu (2004) Application of selective non-catalytic reduction of NOx in small-scale combustion systems. Atmospheric Environment, 38 (39). pp. 6823-6828. ISSN 1352-2310

Wong, Kuan Yew (2004) Characterizing knowledge management in the small business environment. Journal of Knowledge Management, 8 (3). pp. 44-61. ISSN 1367-3270

Salehun, Md Amirul Khair (2004) Comparison of Five Alternative Manufacturing Strategies For increasing Job Shop Capacity and Their Impact on Manufacturing Performance. Masters thesis, Universiti Teknologi Malaysia.

Mat Lazim, Tholudin and Mat, Shabudin and Huong , Yu Saint (2004) Computational Fluid Dynamic Simulation (CFD) and Experimental Study on Wing-external Store Aerodynamic Interference of subsonic Fighter Aircraf. Journal of Advanced Engineering, 44 (2). pp. 9-14. ISSN 1210-2709

Mardani, . (2004) Development Of Intake System For Improvement Of Performance Of Compressed Natural Gas Spark Ignition Engine. PhD thesis, Universiti Teknologi Malaysia.

Kumar Mandal, Nirmala and Abd. Rahman, Roslan and Leong, Mohd Salman (2004) Experimental study on loss factor for corrugated plates by bandwidth method. Ocean Engineering, 31 (10). pp. 1313-1323. ISSN 0029-8018

Ahmad, Robiah (2004) Identification Of Discrete-Time Dynamic Systems Using Modified Genetic Algorithm. PhD thesis, Universiti Teknologi Malaysia.

Yaacob, Mohd Shafiek (2004) Identification Of Non-Linear Dynamic Systems Using Fuzzy System With Constrained Membership Functions. PhD thesis, Universiti Teknologi Malaysia.

Sudin, I. (2004) Investigation into Some Aspects of Partial Ductile Mode in Wet and Dry Grinding of optical Glass. PhD thesis, Universiti Teknologi Malaysia .

Sudin, I. (2004) Investigation into some aspects of partial ductile mode in wet andd dry grinding of optical glass. PhD thesis, Universiti Teknologi Malaysia.

Jusoh, Iberahin and Alias, Amran and Abd Kader, Ab Saman (2004) Maintaining The Standard: Full Time And Part Time Programs At Mechanical Engineering Faculty, UTM. In: Conference On Engineering Education (CEE 2004), 14-15 December 2004, Kuala Lumpur.

Normah , M. G. and A. Hasan, A. and Mazlan, A. W. and M. Kassim, A. J. and Mohsin, S. and Awaludin, M. S. (2004) MEng by Taught Course: The UTM Scenario. In: Conference On Engineering Education (CEE 2004), 14-15 December 2004, Kuala Lumpur.

Mohd. Hashim, Siti Zaiton and Mat Darus, Intan Zaurah and Tokhi, M. 0. (2004) Nonlinear dynamic modelling of flexible beam structures using neural networks. In: Proceedings of the IEEE International Conference on Mechatronic, ICM 2004, 3 - 5th June 2004, Istanbul, Turkey.

Abd Kader, Ab Saman (2004) Professional Engineer’s Roles and Responsibility. In: Conference On Engineering Education (CEE 2004), 14-15 December 2004, Kuala Lumpur.

Jamaludin, Khairur Rijal (2004) Reka Bentuk Sistem: Kuasa Bendalir. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0337-2

Hussain, Mohd Nasir (2004) Rekabentuk Industri Dalam Menjana Kretiviti Jurutera. In: Conference On Engineering Education (CEE 2004), 14-15 December 2004, Kuala Lumpur.

Khandoker, Abul Hossain (2004) Study of Urea Based Selective Non-Catalytic Reduction of NOx in Small Scale Comburtion. Masters thesis, Universiti Teknologi Malaysia.

Beh, Keh Shin (2004) Substrate Warpage analysis During Solger Reflow Process. Masters thesis, UTM Skudai.

Yusof, Ahmad Anas (2004) The Develpment of Microwave Absorber From Oil Palm Shell Carbon. Masters thesis, UTM Skudai.

Yusoff, Lukeman (2004) The Effect of Pressurized Induced Flow on Downdraft gasifire Performance with Low Emission burner. Masters thesis, Universiti Teknologi Malaysia.

Ashrul Ishak, Mohamad Shaiful and Mohd. Jaafar, Mohammad Nazri (2004) The effect of swirl number on discharge coefficient for various orifice sizes in a burner system. Jurnal Mekanikal (17). pp. 99-108. ISSN 0127-3396

Wan Hussin, Wan Nazdah and Daud, Mohd Fadzil and Abdul Majid, Fadzilah Adibah (2003) Design, Fabricate And Testing Of Stationary Magnetic Stirrer Bar For Uniform Mixing Of Cell Culture. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Md. Tap, Masine and Mohamed Shaharoun, Awaluddin and Wan Hussin, Wan Nazdah (2003) Determination Of Felxible Measures In Advanced Manufacturing System And Their Effect In Productivity And Responsiveness. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Dahalan, Md. Nizam and Mohd Jaafar, Mohd Nazri and Wan Ali, Wan Khairuddin and Mamat, Rizalman and Abd. Ghani, Mohd Shaiful Azman (2003) Determining Potassium Nitrate performance as solid rocket propellant for rocket engine. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Daud, Mohd Fadzil and Hanafiah, Khairul Anwar and Wan Hussin, Wan Nazdah (2003) Mechanical Design And Fabrication Of A Prototype Motorized Tricycle For The Disable. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Ismail, Yob Saed and Mohd. Sam, Abdul Rahman and Abu Hassan, Shukur (2003) The Study Of Bonding Behavior Between Fiber Reinforced Polymer Composite Plate And Concrete Prism Under Tropical Climate. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Nusyirwan, Istas Fahrurrazi and Dahalan, Md Nizam (2003) Using Composite Materials To fabrication UAV Wing. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Azmi, Azwan Iskandar and Mohd. Taib, Jamaludin and Muhammad, Zulkepli (2003) Feature extraction from step AP224 file sets. Jurnal Mekanikal (16). pp. 31-46. ISSN 0127-3396

Abd. Rahman, Roslan and Zubair, Mazlan and Amin, Norsham (2003) Finite element modeling, correlation and model updating of stiffened plate. Jurnal Mekanikal (16). pp. 91-106. ISSN 0127-3396

Mailah, Musa and Low, Hook Jong (2003) Intelligent active force control of a three-link manipulator using fuzzy logic. Jurnal Mekanikal (16). pp. 57-78. ISSN 0127-3396

Mohd Jaafar, Mohammad Nazri and Samat, Ismail and Abdul Mookmin, Muhamed Shukri (2003) Mengkaji Keberkesanan Aplikasi Pemusar Udara Ram Bilah Rata Dalam Mengurangkan Emisi Dari Pembakar Berbahan Api Cecair. Jurnal Teknologi F, 39 (F). pp. 11-22. ISSN 0127-9696

Ahmad, Mohd. Haris and Mohd. Jaafar, Mohammad Nazri and Ashrul Ishak, Mohamad Shaiful (2003) Pengaruh nombor pusar ke atas pengurangan emisi NOx dari pembakar berbahan api cecair menggunakan pemusar udara aliran paksi. Jurnal Mekanikal (16). pp. 79-90. ISSN 0127-3396

Wan Nik, Wan Sani and Ani, Farid Nasir and Hassan, Masjuki (2003) Rheological properties of palm oil and palm-mineral oil blend. Jurnal Mekanikal (16). pp. 107-116. ISSN 0127-3396

Aqida, S. N. and Ghazali, M. I. and Hashim, J. (2003) The effects of stirring speed and reinforcement particles on porosity formation in cast MMC. Jurnal Mekanikal (16). pp. 22-30. ISSN 0127-3396

Aqida, S. N. and Ghazali, M. I. and Hashim, J. (2003) The effects of stirring speed and reinforcement particles on porosity formation in cast MMC. Jurnal Mekanikal (16). ISSN 0127-3396

Venkatesh, V. C. and Izman, S. and Sharif, S. and Mon, T. T. and Konneh, K. (2003) Ductile Streaks in Precision Grinding of Hard and Brittle Materials. Academy Proceedings in Engineering Sciences, 28 (5). pp. 915-924. ISSN none

Mohd. Saad, Rozaimi (2003) Kajian pembentukan tegasan dan anjakan pada matalat pemotong disebabkan oleh parameter pemotong menggunakan kaedah unsur tak terhingga (FEA). Masters thesis, Universiti Teknologi Malaysia.

Mat Darus, Intan Zaurah and Tokhi, M. O. (2003) Direct Neuro-AVC modelling and control strategy for vibration suppression of a flexible plate structure. In: The 9th IEEE International Conference on Emerging Technologies and Factory Automation, ETFA2003, 16 - 19 September, Lisbon, Portugal.

Husain, Abdul Rashid (2003) Development of dental material testing equipment. Masters thesis, University of Newcastle Upon Tyne, United Kingdom.

Mohd. Jaafar, Mohamad Nazri and Sulian, Mohd. Sharul (2003) Kajian keberkesanan kaedah pembakaran udara berperingkat ke atas pembakar berbahan api gas. Jurnal Mekanikal (15). pp. 86-96. ISSN 0127-3396

Idris, Jamaliah and Salim, Farid and Suliman, Zahrulail and Osman, Edynoor (2003) Kajian Sifat Kehausan Dan Kekerasan Komposit Matriks Aluminium. Jurnal Teknologi A, 38 (A). pp. 11-24. ISSN 0127-9696

Venkatesh, Vasisht, C. (2003) Precision manufacture of spherical and aspheric surfaces on plastics, glass, silicon and germanium. Current Sciences, 84 (9). pp. 1211-1219.

Hassan, Azman and Wahit, Mat Uzir and Chee, Ching Yern (2003) Mechanical and morphological properties of PP/NR/LLDPE ternary blend - Effect of HVA-2. Polymer Testing, 22 (3). 281 -290. ISSN 0959–8103/2006

Mohd Yusof, Sha'ri and Aspinwall , Elaine (2003) Total quality management implementation frameworks: comparison and review. Total Quality Management, 11 (34). pp. 281-294. ISSN 0954-4127, 1360-0613

Hassan, A. and Nabi Bakhs, M.Sharisff and Shaharoun, A.M and Jamaluddin, H. (2003) Improved SPC chart pattern recognition using statistical features. International Journal of Production Research, 41 (7). pp. 1587-1603. ISSN 1366-588X

Tai, Siew Fong (2003) Materials interaction during soldering and isothermal ageing of Sn-Pb and Sn-Ag-Cu solders on electroless Ni/Au surface finish. Masters thesis, Universiti Teknologi Malaysia.

Ng, Chuan Huat (2003) Sistem rekabentuk corak dan acuan pinggan. Masters thesis, Universiti Teknologi Malaysia.

Yusof, Yusri (2003) Disassemblability evaluation method (DEM) for green product. Masters thesis, Universiti Teknologi Malaysia.

Lee, Lai Kin (2003) Thermal analysis of a vertically based fin array in a bounded region : a numerical experiment. Masters thesis, Universiti Teknologi Malaysia.

Eng Eng , Quek and Yusof , Sha'ri (2003) A survey of TQM practices in the Malaysian electrical and electronic industry. Quality Assurance & Total Quality Management, 14 (1). pp. 63-77. ISSN 0954-4127

Muhamad, Sallehuddin and Hamid, Khairul Azura (2003) A four-seat light airplane design. In: 10th Australian International Aerospace Congress incorporating the 14th National Space Engineering Symposium 2003, 29 July – 1 August 2003, Brisbane, Queensland, Australia.

Tan, Jaan Soon and Ani, Farid Nasir (2003) Diffusional behavior and absorption capacity of palm shell chars for oxygen and nitrogen—the effect of carbonization temperature. Carbon, 41 . pp. 840-842.

Jasmi Hashim, Jasmi Hashim (2003) Glosari Kejuruteraan Bahan. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0304-0

Abu Bakar, A R. and OUYANG, H and Cao, Q (2003) Interface pressure distributions through structural modifications. SAE 2003 Transactions, Journal of Passenger Cars: Mechanical Systems , Vol. 112 (No. 6). pp. 2387-2392.

Jasmi Hashim, Jasmi Hashim (2003) Pemprosesan Bahan. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0306-7

Jasmi Hashim, Jasmi Hashim (2003) Pengenalan Komposit Matriks Logam. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0318-0

Mohd Yusof, Noordin (2003) Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel. PhD thesis, Universiti Teknologi Malaysia.

Wong, Kim Seng (2003) Time domain simulation approach for the safe design of small vessels. Masters thesis, Universiti Teknologi Malaysia.

Mailah, Musa and Jonathan Chong, Wun Shiung (2002) Control Of A Robot Arm Using Iterative Learning Algorithm With A Stopping Criterion. Jurnal Teknologi A, 37 (A). pp. 55-72. ISSN 0127-9696

Syaimak Abu Syukur, Syaimak Abu Syukur and Masine Md Tap, Masine Md Tap (2002) Data Transfer Between Cad System And Rp System: A Report. Jurnal Teknologi A, 37 (A). pp. 37-46. ISSN 0127-9696

Chuan Pei, Lim and Md. Tap, Masine (2002) Improving productivity through line balancing : a case study. Jurnal Mekanikal (14). pp. 48-62. ISSN 0127-3396

Harun, Muhammad Adli and Mohd Rohani, Jafri and Wan Hamid, Wan Harun (2002) Ketepatan Kaedah Pengekosan Berasaskan Aktiviti (Abc) Berbanding Kaedah Pengekosan Tradisional Dalam Pengekosan Produk: Pemangkin Kepada Program 6-Sigma. Jurnal Teknologi A, 36 (A). pp. 23-36. ISSN 0127-9696

N. Mohd. Ghazali, N. Mohd. Ghazali (2002) Numerical Study Of Viscous Effects On Acoustic Waves. Jurnal Teknologi C, 37 (A). pp. 47-54. ISSN 0127-9696

Mohd Jaafar, Mohammad Nazri and Abdul Rahman, Mohd. Rosdzimin and Ishak, Mohamad Shaiful Ashrul and Appalanidu, Kiran Babu (2002) Pengaruh Penyelitan Plat Orifis Dalam Mengurangkan Emisi Dari Pembakar. Jurnal Teknologi F, 37 (F). pp. 45-54. ISSN 0127-9696

V. C. , Venkatesh and S., Izman and Sharif, S. and T. T., Mon and M., Konneh (2002) Precision Micro-Machining of Silicon and Glass. International Conference on Industrial Technology 2002, 2 . pp. 1146-1151.

Mohd. Jaafar, Mohammad Nazri and Samat, Ismail and Abdul Mookmin, Muhamad Shukri (2002) The influence of variable vane angle air swirler on reducing emissions from combustion process. Jurnal Mekanikal (14). pp. 1-9. ISSN 0127-3396

Mat Saman, Muhamad Zameri and Law, Cheak Ying (2002) Work Improvement At A Car Manufacturing Company. Jurnal Teknologi C, 37 (A). pp. 73-87. ISSN 0127-9696

Yaacob, M. S. and Jamaluddin, H. and Wong, K. C. (2002) Fuzzy logic approach for estimation of longitudinal aircraft parameters. Aeronautical Journal, 106 . pp. 585-594. ISSN 0001-9240

Mohd Yusof, Sha’ri (2002) Total Quality Management (TQM) Advancement And Critical Success Factors For Implementation In Manufacturing Small And Medium Sized Enterprise (SMEs). Project Report. Universiti Teknologi Malaysia. (Unpublished)

Musa, Md Nor (2002) Design And Development Of Rotating-Sleeve Refrigerant Compressor. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Mansor, Shuhaimi (2002) Analisis kestabilan statik membujur pesawat terbang ringan. Jurnal Mekanikal (13). pp. 26-45. ISSN 0127-3396

Surjosatyo, Adi and Ani, Farid Nasir (2002) Development Of A Two-Stage Biomass Combustion System For Reducing The Emission Pollutant. Jurnal Teknologi C, 36 (A). pp. 55-68. ISSN 0127-9696

Mohd. Taib, Jamaludin (2002) Feature research : review and future direction. Jurnal Mekanikal (13). pp. 1-10. ISSN 0127-3396

Mailah, Musa and Min Yee, Wong and Jamaluddin, Hishamuddin (2002) Intelligent active force control of a robotic arm using genetic algorithm. Jurnal Mekanikal (13). ISSN 0127-3396

Mohd. Jaafar, Mohammad Nazri and Ani, Farid Nasir and Mustapa, Azizi (2002) Kaedah pengurangan emisi dari pembakar lapisan tetap menggunakan udara tambahan/berperingkat. Jurnal Mekanikal (13). pp. 89-94. ISSN 0127-3396

Musa, Hamidon and Mat Saman, Muhamad Zameri and Hau, Lian Chuan (2002) Management and control of non-direct materials in an electronic company. Jurnal Mekanikal (13). pp. 95-116. ISSN 0127-3396

Ahmad, Robiah and Jamaluddin, Hishamuddin (2002) Radial Basis Function (Rbf) For Non-Linear Dynamic System Identification. Jurnal Teknologi A, 36 (A). pp. 39-54. ISSN 0127-9696

Mat Saman, Muhamad Zameri and Law, Cheak Ying (2002) Work Improvement At A Car Manufacturing Company. Jurnal Teknologi A (36 A). pp. 55-69. ISSN 0127-9696

Wan Ali, Wan Khairuddin (2002) Wideband Microstrip Antennas For Cars And Commercial Vehicle Modern Communication System. Project Report. Faculty of Mechanical Engieering, Skudai, Johor. (Unpublished)

Hamada, S. and Hamada, H. and Suzuki, H. and Tamin, M. N. and Nozue, A. (2002) Microstructure and environment-dependent fatigue crack propagation properties of Ti-48Al intermetallics. Journal of Materials Science, 37 . pp. 1107-1113. ISSN 0022-2461

Kwek, L. C. and Loo, C. K. and Wong, E. K. and Rao, M. V. C. and Mailah, M. (2002) Active Force Control of a 5-link biped robot. IEEE Region 10 Annual International Conference, Proceedings/TENCON, 3 . pp. 1562-1565.

Konneh, M (2002) An Experimental Investigation on Partial-Ductile Mode Grinding of Silicon. PhD thesis, Universiti Teknologi Malaysia.

Ghazali, Mohd Imran (2002) Mekanik Kejuruteraan : Statik Teori, Contoh Penyelesaian dan Masalah Jilid 1. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0254-0

Ghazali, Mohd Imran and Abu Hassan, Shukur (2002) Mekanik Kejuruteraan Statik Teori, Contoh Penyelesaian dan Masalah Jilid 2. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0255-9

Ahmad, R. and Jamaluddin, H. and Hussain, M. A. (2002) Multivariable system identification for dynamic discrete-time nonlinear system using genetic algorithm. In: UNSPECIFIED.

Hayash, Jun’ichi and Horikawa, Toshihide and Takeda, Isao and Muroyama, Katsuhiko and Ani, Farid Nasir (2002) Preparing activated carbon from various nutshells by chemical activation with K2CO3. Carbon, 40 . pp. 2381-2386.

Ani, Farid Nasir and Latiff, zukarnain and ariffin, Mohd Kamal (2002) Termodinamik Gunaan. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0246-X

Jafri, Mohd. Rohani and Chan, Kok Teng (2001) Improving Quality With Basic Statistical Process Control (SPC) Tools: A Case Study. Jurnal Teknologi A, 35 (A). pp. 21-34. ISSN 0127-9696

Mat Alit, Mohamad Isnizam and Mohd. Jaafar, Mohammad Nazri (2001) Pembangunan Pembakar Bahan Api Cecair Beremisi Rendah Di UTM. Jurnal Teknologi A, 35 (A). pp. 71-84. ISSN 0127-9696

Hassan, Azmi and Saleh, Chairul and Baba, Md Deros and Muniyandi, Saravanan (2001) Penggunaan Kaedah Ukur Rujuk Dalam Pemprosesan Seramik Bagi Meningkatkan Kualiti Dan Produktiviti. Jurnal Teknologi A, 35 (A). pp. 57-70. ISSN 0127-9696

Mohd. Rohani, Jafri and Tamat, Suhaimi (2001) Peningkatan Kualiti Reka Bentuk Kerusi Sekolah Rendah Dengan Mengintegrasikan Kaedah Qfd Dan Kejuruteraan Nilai. Jurnal Teknologi A, 35 (A). pp. 35-46. ISSN 0127-9696

Dahalan, Md. Nizam and Lee, Boon Peng (2001) Software development for aerodynamic characteristics estimation of wing-body combination of aircraft at cubsonic speeds. Jurnal Mekanikal (12). pp. 23-33. ISSN 0127-3396

Hashim, Jasmi (2001) The Production Of Cast Metal Matrix Composite By A Modified Stir Casting Method. Jurnal Teknologi A (35 A). pp. 9-20. ISSN 0127-9696

Idris, Mohd. Hasbullah (2001) Processing and evaluation of an investment cast magnesium-base alloys. PhD thesis, Universiti Teknologi Malaysia.

Jawaid, A. and Koksal, S. and Sharif, Safian (2001) Cutting performance and wear characteristics of PVD coated and uncoated carbide tools in face milling Inconel 718 aerospace alloy. Journal of materials processing technology, 116 (1). pp. 2-9.

Ourdjini, A. and Chew, K. C. and Khoo, B. T. (2001) Settling of silicon carbide particles in cast metal matrix composites. Journal of Materials Processing Technology, 116 . pp. 72-76. ISSN 0924-0136

Yaacob, Mohd Shafiek and Jamaluddin, Hishamuddin (2001) Effects Of User Selected Conditions On Modeling Of Dynamic Systems Using Adaptive Fuzzy Model. Jurnal Teknologi A, 34 (A). pp. 45-60.

Muhammad Shuhaimi, Shamsuddin and Jafri, Mohd. Rohani (2001) Kajian Kemungkinan Aplikasi Konsep Mesin Fmea (Failure Mode And Effect Analysis): Kajian Kes Di Seksyen Mills Di Kilang Keluli. Jurnal Teknologi A, 34 . pp. 17-28.

Ahmad, Robiah and Jamaluddin, Hishamuddin (2001) Orthogonal Least Square Algorithm And Its Application For Modelling Suspension System. Jurnal Teknologi A, 34 (A). pp. 71-84. ISSN 0127-9696

Che Mat Isa, Mohamd Azman and Mohd Rohani, Jafri (2001) Peningkatan Kualiti Produk (Billet) Melalui Teknik Asas Kawalan Kualiti. Jurnal Teknologi A, 34 . pp. 29-43.

Yahya, Nizamil Fairuz (2001) Optimisation of plating parameters and performance analysis of black chromium coating for solar thermal energy applications. Masters thesis, Universiti Teknologi Malaysia.

M. Yusof, Sha'ri and Aspinwall, Elaine (2001) Case Studies on The Implementation of TQM in The UK Automotive SMEs. International Journal of Quality & Reliability Management, 18 (7). pp. 722-744. ISSN 0265-671X

Senawi, M Y (2001) Development Of A Building Energy Analysis Package (Beap) And Its Application To The Analysis Of Cool Thermal Energy Storage Systems. PhD thesis, Universiti Teknologi Malaysia.

Hamzah, Esah and Prayitno, Dody and Mohd. Ghazali, Mohd. Zulkifli (2001) Effect of mould tilt angles on the mechanical properties of as-cast al-si alloy. In: International Conference and Exhibition on Advances in Production and Processing of Aluminium, 2001, Bahrain.

Mustapa, Mohammad Sukri (2001) Kesan Parameter Bebanan Ke Atas Kadar Perambatan Retak-Lesu Di Dalam Kelakuan Keluli Tahan Karat 316. Masters thesis, UTM Skudai.

Abdul Rahman, Roslan and Che Ismail, Che Abas and Abdullah, Mohd Yunus (2001) Mekanik Mesin : Teori, Contoh Penyelesaian dan Masalah Edisi Ketiga. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0225-7

Mohd. Jaafar, Mohammad Nazri (2001) Penyelesaian Masalah Dalam Dinamik Gas. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0221-4

Ding, Chin Kwong (2001) Processing And Mechanical Characterization Of H2sm-5 Zeolite Loaded With Transition Metals Catalysis For Single Step Conversion Of Mehthane To Gascoline. Masters thesis, UTM Skudai.

Mansor, Shuhaimi and Ishak, Iskandar Shah and Ong, Meng Wei and Fahrurazi, Istas (2000) Development of a dynamic wind tunnel rig for aircraft pure pitching motion. Jurnal Mekanikal, 2 (10). pp. 46-57. ISSN 0127-3396

Mailah, Musa (2000) Intelligent active force control of a rigid robot arm using embedded iterative learning algorithm. Jurnal Mekanikal, 2 (10). pp. 16-45. ISSN 0127-3396

Mohd. Jaafar, Mohammad Nazri and Andrews, G. E. and MkPadi, M. C. (2000) NOx emission reduction from gas burner system applying water cooling technique. Jurnal Mekanikal, 2 (10). pp. 58-72. ISSN 0127-3396

Darus, Amer Nordin (2000) Streamlike function formulation of entry flow. Jurnal Mekanikal, 2 (10). pp. 73-92. ISSN 0127-3396

Tamin, M. N. and Ghonem, H. (2000) Fatigue damage mechanisms of bridging fibers in titanium metal matrix composites. Journal of Engineering Materials and Technology, Transactions of the ASME . pp. 370-375. ISSN 0094-4289

Md.Sirat, Rozlina and Md.Tap, Masine and Mohd. Shaharoun, Awaluddin (2000) A survey report on implementation of design for assembly (DFA) in Malaysian manufacturing industries. Jurnal Mekanikal (9). ISSN 0127-3396

Md. Sirat, Rozlina and Md. Tap, Masine and Mohd. Shaharoun, Awaluddin (2000) A survey report on implementation of design for assembly(DFA) in malaysian manufacturing industries. Jurnal Mekanikal, 1 (9). pp. 60-75. ISSN 0127-3396

Abd. Rahman, Roslan (2000) Control of vibration power input to semi-infinite anisotropic beam. Jurnal Mekanikal (9). ISSN 0127-3396

Abd. Rahman, Roslan (2000) Control of vibrational power input to semi-infinite anisotropic beam. Jurnal Mekanikal, 1 (9). pp. 43-59. ISSN 0127-3396

Ahmad, Roazam and Mohd. Ja'afar, Mohammad Nazri (2000) Membangunkan pemusar udara untuk kegunaan ke atas pembakar berbahan api cecair. Jurnal Mekanikal, 1 (9). pp. 23-42. ISSN 0127-3396

Abu Bakar, Rosli and Wong, Chee Yeen (2000) Membina perisian untuk aliran yang melalui jasad. Jurnal Mekanikal, 1 (9). pp. 1-22. ISSN 0127-3396

Yusof , S. M. and Aspinwall , E. (2000) A conceptual framework for TQM implementation for SMEs. TQM Magazine, 12 (1). pp. 31-37. ISSN 0954-478X

Suberamaniam, K. (2000) A Study in Cellular Manufacturing Using Production Flow Anylysis (Pfa) Simulation Technique. Masters thesis, Universiti Teknologi Malaysia.

Yaw, Yean Chon (2000) A Study Of Corrosion Properties Of A291/Silp Mmc Produce By Pm Technique. Masters thesis, Universiti Teknologi Malaysia .

Kumrason , Thay Alan (2000) Cogeneration Potential In Selected Malaysian Industries. Masters thesis, Universiti Teknologi Malaysia .

Jambak, Muhammad Ikhwan (2000) Design Of Information Architecture For Flexible Manufacturing Systems. Masters thesis, Universiti Teknologi Malaysia .

Hamad, S. and Nozue, A. and Tamin, M. N. (2000) Fatigue crack growth mechanisms of cast Ti-48Al (at. %) alloy. In: Structures and Materials.

Thirunavakarasu, Prakash (2000) Further Evaluation Of Aerodynamic Characteristics Of The Aero 3 Trainer Aircraft Wing. Masters thesis, Universiti Teknologi Malaysia.

Hussein, S. B. and Jamaluddin, H. and Mailah, M. and Zalzala, A. M. S. (2000) Hybrid intelligent active force controller for robot arms using evolutionary neural networks. Proceedings of the IEEE Conference on Evolutionary Computation, ICEC, 1 . pp. 117-124.

Musa, M. and Rahim, Nurul Izzah Abdul (2000) Intelligent active force control of a robot arm using fuzzy logic. IEEE Region 10 Annual International Conference, Proceedings/TENCON, 2 . pp. 291-296.

Hassan, Adnan and Nabi Baksh, Mohd Shariff and M. Shaharoun, Awaluddin (2000) Issues in quality engineering research. International Journal of Quality & Reliability Management, 17 (8). pp. 858-875. ISSN 0265-671X

Daud, Mohd Fadzil and Hanafiah, Khairul Anwar (2000) Lukisan Kejuruteraan : Panduan Asas. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0177-3

Ariyono, Sugeng (2000) Optimisation Of Gravure Cylinder Plating By Designing And Fabricating The Cylinder Copper Plating Machine. Masters thesis, Universiti Teknologi Malaysia.

M.Yusuf, Md Afendi (2000) Paraffin Wax Application In Automative Modelling. Masters thesis, Universiti Teknologi Malaysia.

Abd Jalil, Mohamad Kasim (2000) Proses Dan Kaedah Reka Bentuk Edisi Pertama. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0200-1 (Unpublished)

Idris, Mohd Hasbullah and Ourdjini, Ali and Hamzah, Esah and Clegg, Allen (2000) Suppression of Mold-Metal Reactions during Investment Casting. In: Magnesium Alloys and their Applications. Wiley InterScience Publisher, pp. 628-634. ISBN 9783527302826

Suprapto, Agus (2000) The Characterisrics And Failure Mechanisms Of Creep And Creep-Thermal Cycling Of Superheater Tube. PhD thesis, Universiti Teknologi Malaysia.

Md. , Kawser and N. A. , Farid (2000) Thermochemical processing of rubber waste to liquid fuel. Plastics, Rubber and Composites Processing and Applications, 29 . pp. 100-104. ISSN 0959-8111

Hussein, Shamsul Bahri and Jamaluddin, Hishamuddin and Mailah, Musa (1999) An intelligent method to estimate the inertia matrix of a robot arm for active force control using on-line neural network training scheme. Jurnal Mekanikal (8). ISSN 0127-3396

Mohd. Rohani, Jafri and Syed Hassan, Syed Ahmad Helmi and Chan, Eu Lene (1999) Characterization of a wave soldering process using Taguchi method. Jurnal Mekanikal (8). ISSN 0127-3396

Mohd. Yusof, Sha'ri (1999) Critical review of total quality management. Jurnal Mekanikal (8). ISSN 0127-3396

Jailani, Mohd. Anuar and Mohd. Jaafar, Mohammad Nazri (1999) Emisi ekzos dari kenderaan bermotor, kesannya ke atas atmosfera dan kaedah pengurangannya : satu kajian. Jurnal Mekanikal (8). ISSN 0127-3396

Mailah, Musa (1999) Design and development of a multi-gripper for use in an automated robotic assembly system. Jurnal Mekanikal (7). ISSN 0127-3396

Mat Saman, Muhamad Zameri and Cheong, Wee Tat (1999) Development and implementation of computer integrated production planning system for job shop company. Jurnal Mekanikal, 1 (7). pp. 1-16. ISSN 0127-3396

Jusoh, Iberahin (1999) Offshore pipeline risk and consequence assessment. Jurnal Mekanikal, 1 (7). pp. 56-71. ISSN 0127-3396

Shamsudin, Zainul Rashid and Mohd. Jaafar, Mohammad Nazri (1999) Pembangunan perisian (VORLATTE) menggunakan kaedah kekisi vorteks bagi menentukan ciri aerodinamik sayap sembarangan. Jurnal Mekanikal, 1 (7). pp. 36-55. ISSN 0127-3396

Hamid, N. H. B. and Hamzah, Esah (1999) Formability of Chromate Conversion Coating on Zinc Electroplated Steel Sheet. In: International conference on computer methods and experimental measurments for surface treatment , September 1999, Itali.

Mohd. Jaafar, Mohammad Nazri (1999) Jadual Aliran Boleh Mampat Satu Dimensi. Penerbit UTM, Johor, Malaysia. ISBN 983-52-0169-2

Prayitno, Dody and Hamzah, Esah and Mohd. Ghazali, Mohd. Zulkifli (1999) Microstructure study on Al-Si bar produced by the new near shape casting technique. In: Scientific Conference of Electron Microscopy Society Malaysia, 1999, Pahang.

Ahmad, Zainal Abidin (1999) Proses Pembuatan Jilid 1. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0145-5

ISLAM, MOHAMMAD NURUL and R. , ZAILANI and ANI, FARID NASIR (1999) Pyrolytic oil from fluidised bed pyrolysis of oil palm shell and its characterisation. Renewable Energy, 17 (1). pp. 73-84. ISSN 0960 - 1481

Ahmad Sabki, Ahmad Fuaad and Ismail, Nasrudin and Abdul Malik, Adi Maimun (1998) Offshore Fishing Vessel Research Vessel’s Repair And Operation Project. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Musa, Hamidon and Thean, C. T. (1998) Process performance monitoring in pewter manufacturing. Jurnal Mekanikal, 2 (6). pp. 12-19. ISSN 0127-3396

Musa, Hamidon and Thean, Chan Tan (1998) Proses performance monitoring in pewter manufacturing. Jurnal Mekanikal (6). ISSN 0127-3396

Abu Hassan, Shukur (1998) Kaedah-kaedah proses pembuatan menghasilkan produk berasaskan bahan rencam (komposit) plastik bertetulangkan gentian kaca (GFRP). Jurnal Mekanikal, 1 (5). pp. 31-47. ISSN 0127-3396

Ahmad, Mohd. Zamani and Abdul Mukti, Mohd. Afifi (1998) Marine technology education for the changing Malaysia : the role of marine technology laboratory at Universiti Teknologi Malaysia. Jurnal Mekanikal (5). ISSN 0127-3396

Jusoh, Iberahin (1998) Onshore pipeline risk and consequence assessment. Jurnal Mekanikal, 1 (5). pp. 1-17. ISSN 0127-3396

Jayaprakash, V. and Ng, Gheok Kuan (1998) Optimisation studies on inclined web wheel using finite elements. Jurnal Mekanikal, 1 (5). pp. 61-77. ISSN 0127-3396

Idris, Jamaliah and Teoh, T. L. (1998) The use of scanning acoustic microscope for flaw detection in metallic materials. Jurnal Mekanikal, 1 (5). pp. 48-60. ISSN 0127-3396

Kannan, K S and Ab. Wahab, Abas and Abdullah, Haryati and Abdul Latif, Zulkarnain and Hassan, Mohamad Yusri (1998) Cogeneration Potential Study In Food Industry. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Hanafiah, Khairul Anwar (1998) Lukisan Kejuruteraan Berbantu Komputer. Penerbit UTM, Johor,Malaysia. ISBN 983-52-0118-8

Mohd. Jaafar, Mohammad Nazri (1997) Development of radial aerodynamic swirlers. Jurnal Mekanikal, 2 (4). pp. 13-28. ISSN 0127-3396

M. Yusuf, Md. Afendi (1997) Experimental study of paraffin wax potential as a physical modelling material for local environment. Jurnal Mekanikal, 2 (4). pp. 64-83. ISSN 0127-3396

Mainal, Mohd. Ramzan and Jaafar, Ghazali (1997) On the strength and vibration analysis of a 8000 dwt container ship propeller. Jurnal Mekanikal, 2 (4). pp. 29-51. ISSN 0127-3396

Ishak, Idris and Abu Hassan, Shukur (1997) Pembuatan panel badan kereta lumba Formula-M daripada bahan polimer komposit (GFRP). Jurnal Mekanikal, 2 (4). pp. 52-63. ISSN 0127-3396

Ishak, Idris and Abu Hassan, Shukur (1997) Pembangunan konsep reka bentuk prototaip kereta Formula-M. Jurnal Mekanikal, 1 (3). pp. 17-35. ISSN 0127-3396

Al-Shayeb, Mohamed and Lie, T. T. and Abd. Ghani, Badri (1997) Sensitivity analysis of columns at extreme temperature. Jurnal Mekanikal, 1 (3). pp. 1-16. ISSN 0127-3396

Jusoh, Iberahin (1997) Stress utilisation of jacket structure under environmental loading. Jurnal Mekanikal, 1 (3). pp. 36-49. ISSN 0127-3396

Mohd. Jaafar, Mohammad Nazri (1997) Emissions from gas burner, their impact on the environment and abatment techniques. Jurnal Mekanikal, 1 (3). pp. 50-70. ISSN 0127-3396

Mailah, Musa and Hewit, J. R. and Meeran, Sheik (1996) Active force control applied to a rigid robot arm. Jurnal Mekanikal, 2 (2). pp. 52-68. ISSN 0127-3396

Abu Bakar, Rosli and Lee, Chang Saik and Chon, Mun Soo (1996) An experimental study on the effect of air-assist and wall-flow distribution in the spark ignition engine performance. Jurnal Mekanikal, 2 (2). pp. 69-80. ISSN 0127-3396

Abdul Ghani, Badri and El-Shayeb, Mohamed and Lie, T. T. (1996) Experimental verification of column at extreme temperature. Jurnal Mekanikal, 2 (2). pp. 35-51. ISSN 0127-3396

Abdul Ghani, Badri and El-Shayeb, Mohamed and Lie, T. T. (1996) Heat transfer and strength analysis of column at extreme temperature. Jurnal Mekanikal, 2 (2). pp. 16-34. ISSN 0127-3396

Mohd. Jaafar, Mohammad Nazri (1996) The application of fuel staging on reducing NOx emissions from gas burner. Jurnal Mekanikal (2). pp. 1-15. ISSN 0127-3396

Sapari, Nasiman and Idris, Azni and Ab. Hamid, Noor Hisham (1996) Total removal of heavy metal from mixed plating rinse wastewater. Desalination, 106 (1-3). pp. 419-422. ISSN 00119164

Amrin, Astuty and Abu Bakar, Yusri (1996) A study of hydrogen embrittlement (HE) on tempered carbon steel. Jurnal Mekanikal, 1 (1). pp. 99-106. ISSN 0127-3396

Jusoh, Iberahin and Wolfram, Julian (1996) Effects of marine growth and hydrodynamic loading on offshore structures. Jurnal Mekanikal, 1 (1). pp. 77-96. ISSN 0127-3396

Mainal, Mohd. Ramzan and Kamil, Mohd. Salim (1996) Estimation of ship manoeuvring characteristics in the conceptual design stage. Jurnal Mekanikal, 1 (1). pp. 44-60. ISSN 0127-3396

Ayob, Md. Razali (1996) Laser light diffraction technique for particle sizing. Jurnal Mekanikal, 1 (1). pp. 1-19. ISSN 0127-3396

Abu, Aminudin (1996) On the theoretical vibration analysis of the exhaust system. Jurnal Mekanikal, 1 (1). pp. 61-76. ISSN 0127-3396

Hussin, Rosli (1996) Enjin Kereta (UTM – DBP). Penerbit UTM, Johor, Malaysia. ISBN 983-62-5520-6

Mainal, Mohd Ramzan and Jusoh, Iberahin and Abd. Rahman, Roslan and Abd. Kader, Ab. Saman (1990) Glosari Teknologi Marin. Penerbit UTM, Johor,Malaysia. ISBN 983-9585-41-X

Mainal, Mohd Ramzan and Abdul Ghani, Badri (1990) Lukisan Kejuruteraan: Buku Kerja 1. Penerbit UTM, Johor,Malaysia. ISBN 983-9585-25-8

Mainal, Mohd Ramzan and Abdul Ghani, Badri (1990) Lukisan Kejuruteraan: Buku Kerja 2. Penerbit UTM, Johor,Malaysia. ISBN 983-9585-36-3

Mainal, Mohd Ramzan and Abdul Ghani, Badri (1990) Lukisan Kejuruteraan: Buku Kerja 3. Penerbit UTM, Johor,Malaysia. ISBN 983-9585-57-6

Ahmad, Mohd Zamani and Yaakob, Omar and Abd. Kader, Ab. Saman and Sinha, R.P. and Olanrewaju, Oladokun Sulaiman An analysis of technological development in propulsion and transportation. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Md. Sirat, Rozlina and Mohamed Shaharoun, Awaluddin and Md. Tap, Masine Application of design for assembly (DFA) in small and medium industries (SMI). Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Ammoo, Mohd. Shariff and Mohd Nayan, Mohd Idham and Hussain, Mohd Nasir Conceptual design of UTM 4-seater helicopter. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Syahrom, Ardiyansyah Design And Development Of Multistage Symmetrical Wobble Compressor. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Krishnan, S and Lee, Choong-Won Development of a 100-n hydrogen peroxide rocket engine. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

K, Li Wei and Mat Saman, Muhamad Zameri and L, Meng Chiao Development of green design framework for Malaysian automotive industries. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Abdul Kadir, Mohammed Rafiq and Kamsah, N. and Aziz, Z. Eccentric Loading on the Tibial Plate After Knee Replacement. In: IFMBE Proceedings. Springer Berlin Heidelberg, pp. 403-406. ISBN 1680-0737

Abdul Kadir, Mohammed Rafiq and N. , Kamsah and M. , Salim Effect of Metal Back Geometry on the Stability of Cementless Acetabular Cup. In: IFMBE Proceedings. Springer Berlin Heidelberg, pp. 410-413. ISBN 1680-0737

Tamin, Mohd Nasir and Hamzah, Esah and Ong, Wei Rex Effects of chromium content on fatigue crack growth behavior of Ti-48Al-xCR alloys. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Adnan, Faizul Amri and Hironori, Yasukawa Experimental investigation of wave-induced motions of an obliquely moving ship. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Ishak, Iskandar Shah and Mansor, Shuhaimi and Mat Lazim, Tholudin Experimental research on helicopter tail shake phenomenon. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Awang, I M and C , Y Leong and Abu Bakar, Abd Rahim and Abdul Ghani, Badri and Abd. Rahman, Roslan and Md. Zain, Mohd. Zarhamdy Modeling and simulation of automotive wiper noise and vibration using finite element method. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Syahrom, Ardiyansyah and Wan Mat, Wan Ali and Abdul-Latif, Ainullotfi and Musa, Md Nor Optimized design of home refueling appliance (HRA) with novel multi-stage symmetrical wobble-plate compressor. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Priyandoko, Gigih and Musa, Mailah and Jamaluddin, Hishamuddin Practical implementation of skyhook and adaptive active force control to an automotive suspension system. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Rahmat, Mohd Zaki Yamani and Mohd. Jaafar, Mohammad Nazri and Abdul-Latif, Ainullotfi and Wan Ali, Wan Khairuddin and Mat Yajid, Zuriana Mariati and Kimsin, Intan Noryanah Propellant development for small rockets. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Kurdi, Ojo and Abd. Rahman, Roslan and Tamin, Mohd. Nasir Stress analysis of heavy duty truck chassis using finite element method. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Priyanto, Agoes and Erwandi, Erwandi and Samudro, Samudro Surge forces of a FPSO at Lee side of submerged plate in regular waves. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Priyandoko, G. and Mailah, M. and Jamaluddin, H. Vehicle active suspension system using skyhook adaptive neuro active force control. Mechanical Systems and Signal Processing . ISSN 0888-3270

Ishak, Iskandar Shah and Mat Lazim, Tholudin and Mansor, Shuhaimi Wind tunnel tests on a generic eurocopter 350Z helicopter. In: 2nd Regional Conference on Vehicle Engineering & Technology, 15 - 16 July 2008, Hotel Istana, Kuala Lumpur.

Md Zain, M. Z. (2006) Hybrid learning control schemes with input shaping of a flexible manipulator system. Mechatronics, 16 (3-4). pp. 209-219. ISSN 0957-4158

Mailah, Musa and Ong, Miaw Yong (2001) Intelligent Adaptive Active Force Control Of A Robotic Arm With Embedded Iterative Learning Algorithms. Jurnal Teknologi A, 35 (A). pp. 85-98. ISSN 0127-9696

Adi, Surjosatyo and Ani, Farid Nasir (2001) A Numerical Study Of Air Flow In A Coaxial Pipe. Jurnal Teknologi A, 34 . pp. 1-15.

D. Prayitno, D. Prayitno and E. Hamzah, E. Hamzah and M.Z.M. Ghazali, M.Z.M. Ghazali and A.J. Clegg, A.J. Clegg (2001) Theoretical Approach On The Growth Rate Of Solidified Metal Interface. Jurnal Teknologi A, 35A . pp. 47-56. ISSN 0127-9696

Yaakob, Omar and Teoh Eng, Lee and Liew Yek, Wai and Koh Kho, King (2005) Design Of Malaysian Fishing Vessel For Minimum Resistance. Jurnal Teknologi A (42 A). pp. 1-12. ISSN 0127-9696

Abdul Wahid, Mazlan and Mohd Jaafar, Mohammad Nazri and Ani, Farid Nasir (2006) Studies On The Effect Of Swirl Intensity And Fuel Mixtures On Combustion And Flame Characteristics Of Swirl Burner. Project Report. Universiti Teknologi Malaysia. (Unpublished)

Tamin, M. N. and Sudin, I. and Mon, T. T. (2008) Thermal-mechanical responses of Ti-6Al-4V during orthogonal cutting process. Diffusion and Defect Data. Pt A Defect and Diffusion Forum, 273-276 . pp. 673-678. ISSN 1012-0386

Wong, Kuan Yew and Aspinwall, Elaine (2006) Development of a knowledge management initiative and system. Expert Systems with Applications, 30 (4). pp. 633-641.

K., Suardia and E., Hamzah and A., Ourdjinia and V. C., Venkatesh (2007) Effect of heat treatment on the diffusion coefficient of hydrogen absorption in gamma-titanium aluminide. Journal of Materials Processing Technology, 185 . pp. 106-112. ISSN 09240136

A., Jawaid and S., Koksal and Sharif, S. (2000) Wear Behavior of PVD and CVD Coated Carbide Tools when Face Milling Inconel 718. Tribology Transactions, 43 . pp. 325-331. ISSN 1547-397X (electronic) 1040-2004 (paper)

A., Jawaid and Sharif, S. and S., Koksal (2000) Evaluation of wear mechanisms of coated carbide tools when face milling titanium alloy. Journal of Materials Processing Technology, 99 . pp. 266-274. ISSN 09240136

Md Deros, Baba and Yusof, Sha'ri Mohd and Md Salleh, Azhari (2006) A benchmarking implementation framework for automotive manufacturing SMEs. Benchmarking: An International Journal, 13 (4). pp. 396-430. ISSN 1463-5771

Yiow, Chong Iyat (2001) Vibro-Acoustic Analysis Of Car Body Structure. Masters thesis, Universiti Teknologi Malaysia.

Abd Rahman, Daud (1994) Mekanik Bahan : Tegasan dan Terikan Mudah. Penerbit UTM, Skudai, Johor, Malaysia. ISBN 983-52-0000-9

Ishak, Idris and Lim, Richard Boon Keat (2007) Introduction to Basic Sketching & Rendering Techniques. Penerbit UTM, Johor, Malaysia. ISBN 978-983-52-0426-5

UNSPECIFIED and Hassan, Azman and Ghazali, Mohd. Imran and Ismail, Ahmad Fauzi (2007) Heat sealability of laminated films with LLDPE and LDPE as the sealant materials in bar sealing application. Journal of Applied Polymer Science, 104 (6). pp. 3736-3745. ISSN 0021-8995

Rashid, Roslina and Jamaluddin, Hishamuddin and Saidina Amin, Nor Aishah (2006) Empirical and feed forward neural networks models of tapioca starch hydrolysis. Applied Artificial Intelligence, 20 (1). pp. 79-97. ISSN 0883-9514

Wan Mohamed, Wan Ahmad Najmi and Ani, Farid Nasir (2002) The effect of fuel feed rate on temperature profiles of a cascading hearth with secondary swirl combustor. Jurnal Mekanikal (13). ISSN 0127-3396

Chong, S.C. and Wong, Kuan Yew and Lin, B.S. (2006) Criteria for measuring KM performance outcomes in organisations. Industrial Management & Data Systems, 106 (7). pp. 917-936. ISSN 0263-5577

UNSPECIFIED (2008) Hard turning of cold work tool steel using wipper ceramic tool. Jurnal Mekanikal (25). pp. 92-105. ISSN 0127-3396

UNSPECIFIED (2008) Interactive framework for dynamic modelling and active vibration control of flexible structures. Jurnal Mekanikal (25). pp. 24-38. ISSN 0127-3396

UNSPECIFIED (2008) Development of 2-D and 3-D double-population thermal lattice boltzmann models. Mathematics Journal of Univesiti Teknologi Malaysia, 24 (1). pp. 53-66. ISSN 0128-4428

Mat Darus, I.Z. and Tokhi, M.O. (2006) Parametric and non-parametric identification of a two dimensional flexible structure. Journal of Low Frequency Noise Vibration and Active Control, 25 (2). pp. 119-143. ISSN 1461-3484

Tawi, Kamarul Baharin (2008) Characterisation of an Electromechanical Clutch for Continuously Variable Transmission (CVT) Application. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Othman, Kahar (2008) Study On Basic Properties of Phase Change Material for Thermal Energy Storage. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Jamaluddin, Hishamuddin (2009) Design And Development Of A Magnetorheological Shock Absorber For Automotive Applications. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)

Yaakob, Omar and Ibrahim, Zaharah and Priyanto, Agoes and Omar, Mohd Shahir Shamir and Adnan, Faizul Amri and Hamdan, Salehuddin and Md Salleh, Madihah and Abdul Wahap, Mohd Arizam (2008) Biomechanics and Hydrodynamics Study od Aquatic Locomotion. Project Report. Faculty of Mechanical Engineering, Skudai, Johor. (Unpublished)